2011 INFINITI QX56 transmission

BCS-70
< DTC/CIRCUIT DIAGNOSIS >
U1000 CAN COMM
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM
DescriptionINFOID:0000000006274829
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H-line, CAN L-line) al lowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-28, "
CAN COMMUNICATION SYSTEM : CAN Communica-
tion Signal Chart".
DTC LogicINFOID:0000000006274830
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000006274831
1.PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of BCM.
Is DTC
“U1000” displayed?
YES >> Refer to LAN-18, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-40, "
Intermittent Incident".
DTCCONSULT-III display
description DTC Detection Condition Possible cause
U1000 CAN COMM When BCM cannot communicate CAN com-
munication signal continuously for 2 seconds
or more.
CAN communication system
Revision: 2010 May2011 QX56

BRC-14
< SYSTEM DESCRIPTION >[WITH VDC]
COMPONENT PARTS
ABS Actuator and Electric Unit (Control Unit)
INFOID:0000000006222561
Electric unit (control unit) is in tegrated with actuator and motor/accumulator assembly and comprehensively
controls VDC function, TCS function, AB S function, EBD function, hill start assist function or brake limited slip
differential function.
ELECTRIC UNIT (CONTROL UNIT)
 Brake fluid pressure, engine and transmission are controlled according to signals from each sensor.
 If malfunction is detected, the system enters fail-safe mode.
ACTUATOR
The following components are integrated with ABS actuator.
Motor/accumulator Assembly
Pump Operates the pump drive according to signals from ABS actuator and electric unit (control unit) by the motor.
Motor Operates the motor drive according to signals fr om ABS actuator and electric unit (control unit).
Accumulator
 The accumulator accumulates brake fluid conveyed by the motor and pump.
Motor Relay
Operates the motor ON/OFF according to signals fr om ABS actuator and electric unit (control unit).
Actuator Relay (Main Relay)
Operates each valve ON/OFF according to signals fr om ABS actuator and electric unit (control unit).
ABS IN Valve and ABS OUT Valve
Increases, holds or decreases the fluid pressure of each caliper according to signals from ABS actuator and
electric unit (control unit).
Cut Valve 1, Cut Valve 2
Shuts off the ordinary brake line from master cylinder to signals from ABS actuator and electric unit (control
unit).
Suction Valve 1
Suction Valve 1 switches the brake path to convey accu mulator pressure to the front system, according to a
signal transmitted from the ABS actuat or and electric unit (control unit).
Suction Valve 2
Suction valve 2 releases accumulator pressure, accord ing to a signal transmitted from the ABS actuator and
electric unit (control unit).
Control Pressure Sensor (models with Advanced Driver Assistance System)
Detects the brake fluid pressure of brake caliper side and transmits a signal to ABS actuator and electric unit
(control unit).
Accumulator Pressure Sensor
The accumulator pressure sensor detects brake fluid pressure accumulated in the accumulator and conveys
the detected result to the ABS act uator and electric unit (control unit).
Master cylinder Pressure Sensor
Detects the brake fluid pressure of master cylinder part and transmits a signal to ABS actuator and electric unit
(control unit).
Wheel Sensor and Sensor RotorINFOID:0000000006222562
NOTE:
 Wheel sensor and sensor rotor is integrated in wheel hub assembly.
 Never measure resistance and voltage value using a tester because sensor is active sensor.
Revision: 2010 May2011 QX56

BRC-16
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000006222569
 The system switches fluid pressure of each brake caliper to increase, to hold or to decrease according to
signals from control unit in ABS actuator and electric unit (control unit). This control system is applied to
VDC function, TCS function, ABS func tion, EBD function, hill start assist function and brake limited slip dif-
ferential (BLSD) function
 Fail-safe function is available for each function and is activated by each function when system malfunction occurs.
 The adoption of the 4WD switch assembly (4WD sh ift switch and VDC OFF switch) enables to change the
control characteristics of the VDC function, the TCS function and the brake limited slip differential (BLSD)
function into an optimal characteristics, based on a st ate of the 4WD shift switch. (Models with 4WD system)
SYSTEM DIAGRAM
NOTE:
Transfer control unit is appli ed to models with 4WD system.
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
JPFIC0182GB
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the follo
wing signals to ABS actuator and elec tric unit (control unit) via com-
munication line
*1.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
ECM Mainly transmits the follo
wing signals to ABS actuator and elec tric unit (control unit) via CAN
communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following si gnals from ABS actuator and electr ic unit (control unit) via CAN
communication.
 Target throttle position signal
Revision: 2010 May2011 QX56

BRC-30
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal G s
ensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD system
OPERATION CHARACTERISTICS
VDC Function That Prevents Oversteer Tendency
 During a cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the outer side of turn. Moment directing towards the outer side of turn is generated. Oversteer is prevented.
 Changing driving lane on a slippery road, when oversteer tendency is judged large, engine output is con- trolled as well as brake force (brake fluid pr essure) of 4 wheels. Oversteer tendency decreases.
VDC Function That Prevents Understeer Tendency
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via com-
munication line
*1.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
ECM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 Target throttle position signal
TCM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Shift position signal
Transfer control unit
*2Mainly transmits the following si gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Current 4WD mode signal
Steering angle sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Steering angle sensor signal
Combination meter Mainly receives
the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 VDC warning lamp signal
 VDC OFF indicator lamp
JPFIC0135GB
JPFIC0136GB
Revision: 2010 May2011 QX56

SYSTEMBRC-31
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
 During a cornering, brake force (brake fluid pressu re) is applied on front wheel and rear wheel on the inner
side of turn. Moment directing towards the inner side of turn is generated. Understeer is prevented.
 Applying braking during a cornering on a slippery road, when understeer tendency is judged large, engine
output is controlled as well as brake force (brake fluid pressure) of four wheels. Understeer tendency
decreases.
TCS FUNCTION
TCS FUNCTION : System DescriptionINFOID:0000000006222573
 Wheel spin status of drive wheel is detected by wheel sensor of 4
wheels. Engine output and transmission shift status is controlled
so that slip rate of drive wheels is in appropriate level. When wheel
spin occurs on drive wheel, ABS ac tuator and electric unit (control
unit) perform brake force control of LH and RH drive wheels (apply
brake force by increasing brake fluid pressure of drive wheel) and
decrease engine torque by engine torque control. Wheel spin
amount decreases. Engine torque is controlled to appropriate
level.
 TCS function can be switched to non-operational status (OFF) by
operating VDC OFF switch. In this case, VDC OFF indicator lamp
turns ON.
 TCS function is not operate when 4WD mode is “4L”. (Models with
4WD system)
 VDC warning lamp blinking while TCS function is in operation and indicates to the driver that the function is in operation.
 Slight vibrations are felt on the brake pedal and the operation noises occur, when TCS function operates. This is not a malfunc-
tion because it is caused by TCS function that is normally oper-
ated.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. W hen a malfunction occurs in TCS
function, the control is suspended for VDC function, TCS function,
hill start assist function and brake limited slip differential (BLSD)
function. The vehicle status becomes the same as models without VDC function, TCS function, hill start
assist function and brake limited slip differential (B LSD) function. However, ABS function and EBD function
are operated normally. Refer to BRC-25, "
Fail-safe".
SYSTEM DIAGRAM
NOTE:
JPFIC0137GB
JPFIC0138GB
JPFIC0139GB
Revision: 2010 May2011 QX56

BRC-32
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Transfer control unit is appli
ed to models with 4WD system.
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal G s ensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD system
ABS FUNCTION
JPFIC0183GB
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via com-
munication line
*1.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
ECM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 Target throttle position signal
TCM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Shift position signal
Transfer control unit
*2Mainly transmits the following si gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Current 4WD mode signal
Steering angle sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Steering angle sensor signal
Combination meter Mainly receives
the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 VDC warning lamp signal
 VDC OFF indicator lamp
Revision: 2010 May2011 QX56

BRC-34
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Transfer control unit is appli
ed to models with 4WD system.
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal G s ensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD system
EBD FUNCTION
EBD FUNCTION : System DescriptionINFOID:0000000006222575
 By preventing rear wheel slip increase through rear wheel brake force (brake fluid pressure) control that is
electronically controlled when slight skip on front and r ear wheels are detected during braking, stability dur-
ing braking is improved.
JPFIC0184GB
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via com-
munication line
*1.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
Transfer control unit
*2Mainly transmits the following si gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Current 4WD mode signal
Combination meter Mainly receives
the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 ABS warning lamp signal
Revision: 2010 May2011 QX56

BRC-36
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
SYSTEM DIAGRAM
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
hill start assist FUNCTION
hill start assist FUNCTION : System DescriptionINFOID:0000000006222576
 This function maintains brake fluid pressure so that
the vehicle does not move backwards even if brake
pedal is released to depress accelerator pedal to start the vehicle while it is stopped on an uphill slope by
depressing brake pedal.
 This function operates when the vehicle is in stop status on a uphill slope of slope ratio 10% or more and
selector lever is in the position other than P or N.
 hill start assist function is only for the start aid. It maintains the brake fluid pressure for approx. 2 seconds after releasing the brake pedal, and then decreases the pressure gradually. If the vehicle can start by the
accelerator operation, the brake is released automatically and a smooth start can be performed.
 Fail-safe function is adopted. When a malfunction occurs in hill start assist function, the control is suspended
for VDC function, TCS function, hill start assist func tion and brake limited slip differential (BLSD) function.
The vehicle status becomes the same as models without VDC function, TCS function, hill start assist func-
tion and brake limited slip differential (BLSD) functi on. However, ABS function and EBD function are oper-
ated normally. Refer to BRC-25, "
Fail-safe".
JPFIC0144GB
Component Signal description
Combination meter Mainly receives
the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 Brake warning lamp signal
Revision: 2010 May2011 QX56