2011 INFINITI QX56 key

OUTSIDE KEY ANTENNADLK-257
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
DLK
N
O P
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Remova l and InstallationINFOID:0000000006226122
REMOVAL
Remove the driver side outside handle. Refer to DLK-241, "OUTSIDE HANDLE : Removal and Installation".
INSTALLATION
Install in the reverse order of removal.
PASSENGER SIDE
PASSENGER SIDE : Removal and InstallationINFOID:0000000006226123
REMOVAL
Remove the passenger side outside handle. Refer to DLK-241, "OUTSIDE HANDLE : Removal and Installa-
tion".
INSTALLATION
Install in the reverse order of removal.
BACK DOOR
BACK DOOR : Removal and InstallationINFOID:0000000006226124
REMOVAL
Remove the back door finisher inner. Refer to INT-39, "Removal and Installation".
INSTALLATION
Install in the reverse order of removal.
Revision: 2010 May2011 QX56

DLK-258
< REMOVAL AND INSTALLATION >
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Removal and InstallationINFOID:0000000006226125
REMOVAL
Remove the Intelligent Key warning buzzer mounting bolt, and then remove the Intelligent Key warning
buzzer.
INSTALLATION
Install in the reverse order of removal.
Revision: 2010 May2011 QX56

REMOTE KEYLESS ENTRY RECEIVERDLK-259
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
DLK
N
O P
REMOTE KEYLESS ENTRY RECEIVER
Removal and InstallationINFOID:0000000006226126
REMOVAL
1. Remove the luggage side finisher. Refer to INT-38, "LUGGAGE SIDE UPPER FINISHER : Removal and
Installation".
2. Remove the remote keyless entry receiver mounting bolt, and then remove remote keyless entry receiver.
INSTALLATION
Install in the reverse order of removal.
Revision: 2010 May2011 QX56

DLK-260
< REMOVAL AND INSTALLATION >
INTELLIGENT KEY BATTERY
INTELLIGENT KEY BATTERY
Removal and InstallationINFOID:0000000006226127
1. Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2. Insert a flat-blade screwdriver (A) wrapped with a cloth into the slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
 Do not touch the circuit board or battery terminal.
 The key fob is water-resistant. However, if it does get wet,immediately wipe it dry.
3. Replace the battery with new one.
4. Align the tips of the upper and lower parts, and then push them together until it is securely closed.
CAUTION:
 When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
 After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement :Coin-type lithium battery
(CR2025)
PIIB6222E
Revision: 2010 May2011 QX56

ECM
EC-103
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*1: 1st trip DTC No. is
the same as DTC No.
P1572 1572 ASCD BRAKE SW — 1 —
EC-438
(with ASCD)
EC-443
(with ICC)
P1574 1574 ASCD VHL SPD SEN — 1 — EC-447
(with ASCD)
EC-449
(with ICC)
P1606 1606 VVEL CONTROL MODULE — 1 or 2 × or — EC-451
P1607 1607 VVEL CONTROL MODULE — 1 ×EC-452
P1608 1608 VVEL SENSOR POWER/CIRC — 1 ×EC-453
P1610 1610 LOCK MODE — 2 — SEC-53
P1611 1611 ID DISCORD IMMU-ECM — 2 —SEC-54
P1612 1612 CHAIN OF ECM-IMMU — 2 — SEC-55
P1613 1613 ECM INT CIRC-IMMU — 2 —SEC-48
P1614 1614 CHAIN OF IMMU-KEY — 2 —SEC-56
P1615 1615 DIFFERENCE OF KEY — 2 —SEC-48
P1650 1650 STR MTR RELAY 2 — 2×SEC-48
P1651 1651 STR MTR RELAY — 2 ×SEC-48
P1652 1652 STR MTR SYS COMM — 1 ×SEC-48
P1730 1730 INTERLOCK — 2 ×TM-140
P1734 1734
7GR INCORRECT RATIO*7—2 ×TM-142
P1805 1805 BRAKE SW/CIRCUIT — 2 — EC-455
P2100 2100 ETC MOT PWR-B1 — 2×EC-458
P2101 2101 ETC FNCTN/CIRC-B1 — 1 ×EC-460
P2103 2103 ETC MOT PWR — 1 ×EC-458
P 2 11 8 2 11 8 E T C M O T- B 1 — 1 ×EC-464
P 2 11 9 2 11 9 E T C A C T R - B 1 — 1 ×EC-466
P2122 2122 APP SEN 1/CIRC — 1 ×EC-468
P2123 2123 APP SEN 1/CIRC — 1 ×EC-468
P2127 2127 APP SEN 2/CIRC — 1 ×EC-471
P2128 2128 APP SEN 2/CIRC — 1 ×EC-471
P2135 2135 TP SENSOR-B1 — 1 ×EC-475
P2138 2138 APP SENSOR — 1 ×EC-478
P2539 2539 LOW FUEL PRES SEN — 2 ×EC-483
P2541 2541 LOW FUEL PRES SEN — 2 ×EC-483
P2542 2542 LOW FUEL PRES SEN — 2 ×EC-483
P2713 2713 PRESS CONTROL SOL D — 2 ×TM-147
P2722 2722 PRESS CONTROL SOL E — 2 ×TM-148
P2731 2731 PRESS CONTROL SOL F — 2 ×TM-149
P2807 2807 PRESS CONTROL SOL G — 2 ×TM-150
P2A00 2A00 A/F SENSOR1 (B1) — 2 ×EC-487
P2A03 2A03 A/F SENSOR1 (B2) — 2 ×EC-487
DTC*1
Items
(CONSULT-III screen terms) SRT code Trip MIL Reference
page
CONSULT-III
GST*
2ECM*3
Revision: 2010 May2011 QX56

EC-140
< BASIC INSPECTION >[VK56VD]
BASIC INSPECTION
2. Rev engine between 2,000 and 3,000 rpm 2 or 3 times under no
load, then run engine at idle speed for approximately 1 minute.
3. Check idle speed.
For procedure, refer to EC-530, "
Inspection".
For specification, refer to EC-538, "
Idle Speed".
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 4.
4.PERFORM ACCELERATOR PEDAL RE LEASED POSITION LEARNING
1. Stop engine.
2. Perform EC-146, "
Work Procedure".
>> GO TO 5.
5.PERFORM THROTTLE VALVE CL OSED POSITION LEARNING
Perform EC-147, "
Work Procedure".
>> GO TO 6.
6.PERFORM IDLE AIR VOLUME LEARNING
Perform EC-148, "
Work Procedure".
Is Idle Air Volume Learning carried out successfully?
YES >> GO TO 7.
NO >> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
7.CHECK IDLE SPEED AGAIN
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed. For procedure, refer to EC-530, "
Inspection".
For specification, refer to EC-538, "
Idle Speed".
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 8.
8.DETECT MALFUNCTIONING PART
Check the Following.
 Check camshaft position sensor and circuit. Refer to EC-303, "
DTC Logic".
 Check crankshaft position sensor and circuit. Refer to EC-299, "
DTC Logic".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace malfunctioning part. Then GO TO 4.
9.CHECK ECM FUNCTION
1. Substitute with a non-malfunctioning ECM to check EC M function. (ECM may be the cause of the incident,
although this is rare.)
2. Perform initialization of IVIS (NATS) system and regist ration of all IVIS (NATS) ignition key IDs. Refer to
SEC-51, "
ECM : Work Procedure".
>> GO TO 4.
10.CHECK IGNITION TIMING
1. Run engine at idle.
2. Check ignition timing with a timing light. For procedure, refer to EC-531, "
Inspection".
PBIA8513J
Revision: 2010 May2011 QX56

EC-142
< BASIC INSPECTION >[VK56VD]
BASIC INSPECTION
2. Perform initialization of IVIS (NATS) system and regist
ration of all IVIS (NATS) ignition key IDs. Refer to
SEC-51, "
ECM : Work Procedure".
>> GO TO 4.
19.INSPECTION END
If ECM is replaced during this BASIC INSPECTION procedure, perform EC-143, "
Work Procedure".
>> INSPECTION END
Revision: 2010 May2011 QX56

ADDITIONAL SERVICE WHEN REPLACING ECMEC-143
< BASIC INSPECTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ADDITIONAL SERVICE WHEN REPLACING ECM
DescriptionINFOID:0000000006217740
When replacing ECM, the following procedure must be performed.
Work ProcedureINFOID:0000000006217741
1.PERFORM INITIALIZATION OF IVIS (NATS) SYSTEM AND REGISTRATION OF ALL IVIS (NATS) IGNI-
TION KEY IDS
Perform initialization of IVIS (NATS) system and registration of all IVIS (NATS) ignition key IDs. Refer to SEC-
51, "ECM : Work Procedure".
>> GO TO 2.
2.PERFORM VIN REGISTRATION
Perform VIN registration. Refer to EC-145, "
Work Procedure".
>> GO TO 3.
3.PERFORM ACCELERATOR PEDAL RE LEASED POSITION LEARNING
Perform accelerator pedal released position learning. Refer to EC-146, "
Work Procedure".
>> GO TO 4.
4.PERFORM THROTTLE VALVE CL OSED POSITION LEARNING
Perform throttle valve closed position learning. Refer to EC-147, "
Work Procedure".
>> GO TO 5.
5.PERFORM IDLE AIR VOLUME LEARNING
Perform idle air volume learning. Refer to EC-148, "
Work Procedure".
>> END
Revision: 2010 May2011 QX56