2011 INFINITI QX56 sensor

SBC-10
< SYSTEM DESCRIPTION >
SYSTEM
SEAT BELT WARNING LAMP SYSTEM
SEAT BELT WARNING LAMP SYSTEM : System DiagramINFOID:0000000006237880
SEAT BELT WARNING LAMP SYSTEM : System DescriptionINFOID:0000000006237881
 Turns ON seat belt warning lamp, when the Occupant Detection System judges adult or child in the front
passenger seat and the passenger seat belt buckle switch is OFF.
 Operation of air bag diagnosis sensor unit when air bag diagnosis sensor unit receives information from
Occupant Detection System.
 In addition, seat belt warning lamp illuminates, when t he driver side seat belt is not fasten. This does not
relate to the air bag diagnosis sensor unit.
 For driver seat belt function, refer to MWI-16, "
MASTER WARNING LAMP : System Diagram"
JMHIA0685GB
Status (front passenger seat) Seat belt warning lamp (When front passenger seat is unbuck-
led)
Empty OFF
An object OFF
Child/ child-seat ON
Adult ON
Malfunction OFF
Zero point reset
Not yet performed (service parts only) OFF
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (PRE-CRASH SEAT BELT)SBC-11
< SYSTEM DESCRIPTION >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
DIAGNOSIS SYSTEM (P RE-CRASH SEAT BELT)
CONSULT-III FunctionINFOID:0000000006237882
Diagnosis for pre-crash seat belt syst em can be performed using CONSULT-III.
APPLICATION ITEM
SELF-DIAGNOSIS RESULTS
Refer to SBC-16, "DTC Index".
CAUTION:
When malfunctions are detect ed in several systems, includin g CAN communication [U1000], trouble-
shoot CAN communication [U1000].
A malfunction of system may be disp layed when battery voltage is low (when 7 to 8 V is continued for
approximately 2 seconds) even though the system is not malfunctioning. Erase DTC memory and
never replace any parts after making sure that the syst em is normal, especially if the malfunctions are
displayed after replacing battery.
ERASING SELF-DIAGNOSIS RESULTS
 SELF-DIAGNOSIS RESULTS Current “SELF-DIAG RESULTS” are displayed. (If all suspect circuits have been repaired, “NO DTC” is dis-
played.)
DATA MONITOR
Part to be diagnosed Diagnosis Mode Function description
Pre-crash seat belt Self-diagnosis Results
 Displays data recorded when a malfunction is de-
tected.
 Erases DTC recorded in memory.
Data Monitor Displays input data for pre-crash seat belt control
unit in real time.
Work Support Changes the setting for each system function.
CAN DIAG SUPPORT MNTR Monitors communication status of CAN communi-
cation.
Ecu Identification Displays pre-crash seat belt control unit part num-
ber.
Monitor item Contents
BUCKLE SW RH Indicates [ON/OFF] condition of seat belt buckle switch (RH).
BUCKLE SW LH Indicates [ON/OFF] condition of seat belt buckle switch (LH).
VEHICLE DISTANCE Indicates [ON/OFF] condit ion of intelligent brake assist signal.
IGN SW Indicates [ON/OFF] condition of ignition switch.
FR DOOR SW RH Indicates [Close/Open] condition of front door switch (RH).
FR DOOR SW LH Indicates [Close/Open] condition of front door switch (LH).
ABS ACTIVATING Indicates [ON/OFF] co ndition of ABS operation signal.
VHCL SPEED Indicates [Km/h] vehicle speed signal.
BRK PEDAL SNSR1 Indicates [V] voltage of brake pedal stroke sensor 1 signal.
BRK PEDAL SNSR2 Indicates [V] voltage of brake pedal stroke sensor 2 signal.
STRG ANGLE Indicates [deg] steering angle signal.
STRG ANGLE SPEED Indicates [deg/s] steering angle speed signal.
INCLINATION JDMT Indicates [ON/OFF] condition of pre roll over signal.
PRE-TEN ACTIVTN Indicates [ON/OFF] condition of pre-tensioner operated signal.
HEAT PROTC RH Indicates [ON/OFF] condition of heat protection (RH).
HEAT PROTC LH Indicates [ON/OFF] condition of heat protection (LH).
Revision: 2010 May2011 QX56

SBC-14
< ECU DIAGNOSIS INFORMATION >
PRE-CRASH SEAT BELT CONTROL UNIT (DRIVER SIDE)
TERMINAL LAYOUT
PHYSICAL VALUES
Fail SafeINFOID:0000000006237884
 When a system malfunction is detected, deactivates a part of the system or all functions depending on the
malfunctioning part.
 When the malfunction condition recovers to the normal condition, the system returns to the normal opera-
tion.
JMHIA0711ZZ
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
1
(Y) Ground Power supply Input — Battery voltage
2
(G) Ground Brake pedal stroke sensor signal 1 Input Brake released
→ depressed 1 V - 4 V
4
(P) Ground CAN-L Input/
Output ——
6
(LG/R) Ground Seat belt buckle switch signal Input Seat belt is fastened 0 V
Seat belt is unfastened 5 V
8
(G) Ground Local Communication Line 2 Output IGN ON 5 V
9
(–) Ground Shield — — —
10
(R) Ground Brake pedal stroke sensor power circuit Output IGN ON 5 V
12
(B) Ground Brake pedal stroke sensor signal 2 Input Brake released
→ depressed 4 V - 1 V
14
(L) Ground CAN-H Input/
Output ——
16
(W) Ground Local Communication Line 1 Input/
Output ——
17
(W) Ground Brake pedal stroke sensor ground circuit — — 0 V
18
(B) Ground Ground — — 0 V
19
(W) Ground Motor drive circuit power supply Input — Battery voltage
20
(B) Ground Motor drive circuit ground — — 0 V
Revision: 2010 May2011 QX56

SBC-16
< ECU DIAGNOSIS INFORMATION >
PRE-CRASH SEAT BELT CONTROL UNIT (DRIVER SIDE)
DTC Index
INFOID:0000000006237885
DTC Trouble diagnosis name
(CONSULT-III display) DTC detection condition Reference
U0126 STRG ANG SEN SIG Steering angle sensor malfunction is received SBC-33
U0428 STRG ANGL CAL Steering angle sensor calibration incomplete signal is receivedSBC-34
U1000 CAN COMM CIRCUITPre-crash seat belt control unit cannot transmit and receive CAN
communication signal for 2 seconds or more SBC-35
B2451 SEAT BLT MTR DR CIRC Motor or control unit malfunction
 Seat belt motor circuit is open or shorted
SBC-36
B2452 SEAT BLT MTR AS CIRC Motor or control unit malfunction
 Seat belt motor circuit is open or shorted SBC-37
B2453 BR_STROKE_SEN_CIRC
 Brake pedal stroke sensor malfunction
 Brake pedal stroke sensor circuit is open or shorted SBC-38
B2454 SEAT BLT PWR DR CIRC Motor power su
pply circuit is open or shortedSBC-41
B2455 CONTROL UNIT DR Malfunction in pre-crash seat belt control unit SBC-42
B2456 SEAT BLT PWR AS CIRC Motor power supply circuit is open or shortedSBC-43
B2457 CONTROL UNIT AS Malfunction in pre-crash seat belt control unit SBC-44
B2458 LOCAL COMM Local communication line open or shortedSBC-45
B2461 VHCL SPEED SIGNAL Vehicle speed signal malfunction is received SBC-47
B2463 ROLLOVER SIGNAL Rollover signal malfunction is received SBC-48
B2466 DR/AS CONTROL UNIT Control unit is out of the vehicle specificationSBC-49
B2470 SYS HEAT PROTC DRDeactivation for cooling to prevent system heating due to continuous
operation SBC-50
B2471 SYS HEAT PROTC ASDeactivation for cooling to prevent system heating due to continuous
operation
SBC-51
Revision: 2010 May2011 QX56

U0126 ST ANG SEN SIGSBC-33
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
DTC/CIRCUIT DIAGNOSIS
U0126 ST ANG SEN SIG
DescriptionINFOID:0000000006237891
Inputs the steering angle signal from steering angle sensor via CAN communication.
DTC LogicINFOID:0000000006237892
DTC DETECTION LOGIC
NOTE:
If DTC U0126 is displayed with DTC U1000, first per form the trouble diagnosis for DTC U1000. Refer to SBC-
35, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-33, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237893
1.CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Check “Self-diagnostic result” for “ABS” with CONSULT-III. Refer to BRC-40, "
CONSULT-III Function".
Is DTC detected?
YES >> Repair or replace malfunctioning parts.
NO >> GO TO 2.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
U0126 ST ANG SEN SIG Receipt of a malfunction signal of Steering angle signal Steering angle sensor
Revision: 2010 May2011 QX56

SBC-34
< DTC/CIRCUIT DIAGNOSIS >
U0428 STRG ANGL CAL
U0428 STRG ANGL CAL
DescriptionINFOID:0000000006237894
Inputs the steering calibration incomplete signal from steering angle sensor via CAN communication.
DTC LogicINFOID:0000000006237895
DTC DETECTION LOGIC
NOTE:
If DTC U0428 is displayed with DTC U0126, first perform the trouble diagnosis for DTC U0126. Refer to SBC-
33, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-34, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237896
1.CHECK DTC WITH “ABS ACTUATOR A ND ELECTRIC UNIT (CONTROL UNIT)”
Check “Self-diagnostic result” for “ABS” with CONSULT-III. Refer to BRC-40, "
CONSULT-III Function".
Is DTC detected?
YES >> Repair or replace malfunctioning parts.
NO >> GO TO 2.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
U0428 STRG ANGL CAL Receipt of the calibration incomplete signal Steering angle sensor calibration incomplete
Revision: 2010 May2011 QX56

U1000 CAN COMM CIRCUITSBC-35
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G
I
J
K L
M A
B
SBC
N
O P
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000006237897
 CAN (Controller Area Network) is a serial communica tion line for real time applications. It is an on board
multiplex communication line with high data communication speed and excellent error detection ability. A
modern vehicle is equipped with many ECMs, and each cont rol unit shares information and links with other
control units during operation (not independent). In CA N communication, two control units are connected
with two communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with
less wiring. Each control unit transmits/receive s data but selectively reads required data only.
 It transmits the vehicle status to pre-crash seat belt control unit using the CAN communication system.
 It consists of CAN system (unified meter and A/ C amp., ICC sensor, BCM, steering angle sensor).
 Refer to LAN-27, "
CAN COMMUNICATION SYSTEM : CA N System Specification Chart".
DTC LogicINFOID:0000000006237898
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self-diagnostic result” with CONSULT-III.
Is any DTC detected?
YES >> Refer to LAN-27, "CAN COMMUNICATION SYSTEM : CA N System Specification Chart".
NO >> CAN communication system is normal.
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
U1000 CAN communication
circuit Pre-crash seat belt control unit cannot transmit and re-
ceive CAN communication system for 2 seconds or
more.  Harness or connectors
(CAN communication line is open
or shorted)
Revision: 2010 May2011 QX56

SBC-38
< DTC/CIRCUIT DIAGNOSIS >
B2453 BR STROKE SEN CIRC
B2453 BR STROKE SEN CIRC
DTC LogicINFOID:0000000006237903
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.SELF-DIAGNOSIS WITH PRE-CRASH SEAT BELT CONTROL UNIT
1. Turn ignition switch ON.
2. Check “Self-diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SBC-38, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006237904
1.CHECK PRE-CRASH SEAT BELT CONTROL UNIT INPUT SIGNAL
1. Turn ignition switch ON.
2. Select “BRK PEDAL SNSR1” and “BRK PEDAL SNSR2” in “DATA MONITOR” mode with CONSULT-III.
3. Check “BRK PEDAL SNSR1” and “BRK PEDAL SNSR2” indication under the following conditions.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 2.
2.CHECK BRAKE PEDAL STROKE SENSOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect brake pedal stroke sensor harness connector.
3. Check voltage between brake pedal stroke sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.CHECK BRAKE PEDAL STROKE SENSOR POWER SUPPLY CIRCUIT
1. Disconnect pre-crash seat belt contro l unit (driver side) harness connector.
2. Check continuity between pre-crash seat belt c ontrol unit (driver side) harness connector and brake pedal
stroke sensor harness connector.
DTC No. Self-diagnosis item DTC Detection Condition Possible causes
B2453 BR STROKE SEN CIRC Circuit of brake pedal stroke sensor out-
put is open or shorted  Harness or connectors
(The sensor circuit is open or shorted)
 Pre-crash seat belt co ntrol unit (driver side)
 Brake pedal stroke sensor
Monitor item Condition Voltage (V)
(Approx.)
BRK PEDAL SNSR1 Brake released → depressed 1
→ 4
BRK PEDAL SNSR2 4 → 1
Brake pedal stroke sensor
GroundVoltage (V)
(Approx.)
Connector Terminal
E 111 2 5
Pre-crash seat belt control unit (driver side) Brake pedal stroke sensor Continuity
Connector Terminal Connector Terminal
B9 10 E111 2 Existed
Revision: 2010 May2011 QX56