2010 YAMAHA TZR50 Owners Manual

EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU39086
To check the coolant level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
TIP
●The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
●Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
2. Check the coolant level in the
coolant reservoir.
TIP
The coolant should be between the
minimum and maximum level marks.
1. Coolant reservoir
2. Maximum level mark
3. Minimum level mark
3. If the coolant is at or below the
minimum level mark, remove
panel A. (See page 6-8).
4. Remove the coolant reservoir
cap, add coolant to the maxi-
mum level mark, and then install
the reservoir cap. WARNING!
Remove only the coolant reser-
voir cap. Never attempt to
remove the radiator cap when
the engine is hot.
[EWA15161]. NOTI-
CE: If coolant is not available,use distilled water or soft tap
water instead. Do not use hard
water or salt water since it is
harmful to the engine. If water
has been used instead of coo-
lant, replace it with coolant as
soon as possible, otherwise
the cooling system will not be
protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant
as soon as possible, otherwise
the effectiveness of the coolant
will be reduced.
[ECA10472]
1. Coolant reservoir cap
PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
6
5WX-F8199-E3 7/11/08 16:51 Página 49

5. Install the panel.
EAUS1601
To change the coolant
1. Put the vehicle on a level surface
and let the engine cool if neces-
sary.
2. Remove cowling C and panel A.
(See page 6-8).
3. Place a container under the engi-
ne to collect the used coolant.
4. Remove the radiator cap retai-
ning bolt, radiator cap retainer
and radiator cap. WARNING!
Never attempt to remove the
radiator cap when the engine is
hot.
[EWA10381]
1. Radiator cap retaining bolt
2. Radiator cap
3. Radiator cap retainer
5. Remove the coolant drain bolt to
drain the cooling system.
1. Coolant drain bolt
6. Remove the coolant reservoir
cap.7. Disconnect the coolant reservoir
hose on the reservoir side and
drain the coolant from the reser-
voir.
1. Coolant reservoir
2. Coolant reservoir hose
8. After draining the coolant, tho-
roughly flush the cooling system
with clean tap water.
9. Replace the coolant drain bolt
washer if it is damaged, and then
tighten the coolant drain bolt to
the specified torque.
10. Connect the coolant reservoir
hose.
Tightening torque:
Coolant drain bolt:
9 Nm (0.9 m•kgf, 6.5 ft•lbf)
Coolant reservoir capacity (up to
the maximum level mark):
0.29 L (0.31 US qt, 0.26 Imp.qt)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-14
6
5WX-F8199-E3 7/11/08 16:51 Página 50

11. Pour the recommended coolant
into the radiator until it is full.
12. Install the radiator cap.
13. Run the engine several minutes.
Stop the engine and recheck the
coolant level in the radiator. If it is
low, add more coolant until it rea-
ches the top of the radiator.
14. Install the radiator cap, radiator
cap retainer and radiator cap
retaining bolt.
15. Fill the coolant reservoir with
coolant up to the maximum level.
16. Install the coolant reservoir cap
and check for coolant leakage.TIP
If any leakage is found, ask a Yamaha
dealer to inspect the cooling system.
17. Install the cowling and the panel.
EAU40371
Air filter element
The air filter element should be clea-
ned or replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart. Have a Yamaha
dealer clean or replace the air filter
element.Recommended antifreeze:
High quality ethylene glycol
antifreeze containing corrosion
inhibitors for aluminum engines
Antifreeze/water mixing ratio:
1:1
Coolant quantity:
Radiator capacity (including all
routes):
0.70 L (0.74 US qt, 0.62 Imp.qt)
Coolant reservoir capacity:
0.29 L (0.31 US qt, 0.26 Imp.qt)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-15
6
5WX-F8199-E3 7/11/08 16:51 Página 51

EAU21280
Adjusting the carburetor
The carburetor is an important part of
the engine and requires very sophisti-
cated adjustment. Therefore, most
carburetor adjustments should be left
to a Yamaha dealer, who has the
necessary professional knowledge
and experience. The adjustment des-
cribed in the following section, howe-
ver, may be serviced by the owner as
part of routine maintenance.
ECA10550
The carburetor has been set and
extensively tested at the Yamaha
factory. Changing these settings
without sufficient technical know-
ledge may result in poor perfor-
mance of or damage to the engine.
EAU33482
Adjusting the engine idling
speed
The engine idling speed must be
checked and, if necessary, adjusted
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
The engine should be warm before
making this adjustment.
1. Remove panel B. (See page 6-8).
2. Check the engine idling speed
and, if necessary, adjust it to spe-
cification by turning the idle
adjusting screw. To increase the
engine idling speed, turn the
screw in direction (a). To decrea-
se the engine idling speed, turn
the screw in direction (b).
1. Idle adjusting screw
TIP
If the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.
3. Install the panel.
Engine idling speed:
1250–1350 r/minNOTICE
PERIODIC MAINTENANCE AND ADJUSTMENT
6-16
6
5WX-F8199-E3 7/11/08 16:51 Página 52

EAU21370
Adjusting the throttle cable
free play
1. Throttle cable free play
The throttle cable free play should
measure 4.0–6.0 mm (0.16–0.24 in) at
the throttle grip. Periodically check
the throttle cable free play and, if
necessary, adjust it as follows.
TIP
The engine idling speed must be
correctly adjusted before checking
and adjusting the throttle cable free
play.
1. Loosen the locknut.2. To increase the throttle cable free
play, turn the adjusting nut in
direction (a). To decrease the
throttle cable free play, turn the
adjusting nut in direction (b).
1. Locknut
2. Adjusting nut
3. Tighten the locknut.
EAU21562
Tires
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be chec-
ked and, if necessary, adjusted befo-
re each ride.
EWA10501
Operation of this vehicle with
improper tire pressure may cause
severe injury or death from loss of
control.
●The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperatu-
re of the tires equals the
ambient temperature).
●The tire air pressure must be
adjusted in accordance with
the riding speed and with the
total weight of rider, passenger,
cargo, and accessories appro-
ved for this model.
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-17
6
5WX-F8199-E3 7/11/08 16:51 Página 53

EWA10511
Never overload your vehicle. Ope-
ration of an overloaded vehicle
could cause an accident.
Tire inspection
1. Tire tread depth
2. Tire sidewall
The tires must be checked before
each ride. If the center tread depth
reaches the specified limit, if the tire
has a nail or glass fragments in it, or if
the sidewall is cracked, have a Yama-
ha dealer replace the tire immediately.
TIP
The tire tread depth limits may differ
from country to country. Always
comply with the local regulations.
Tire information
This motorcycle is equipped with cast
wheels and tubeless tires.
EWA10461
The front and rear tires should be of
the same make and design, other-
wise the handling characteristics of
the vehicle may be different, which
could lead to an accident.
After extensive tests, only the tires lis-
ted below have been approved for
this model by Yamaha Motor España,
S.A.
Front tire:
Size:
100/80 17 (52H)
Manufacturer/model:
Pirelli / Sport Demon
Continental / Conti-Twist SM
Rear tire:
Size:
130/70 17 (62H)
Manufacturer/model:
Pirelli / Sport Demon
Continental / Conti-Twist SM
WARNING
Minimum tire tread depth (front
and rear):
1.6 mm (0.06 in)
1
2
ZAUM0054
WARNING
Tire air pressure (measured on
cold tires):
0–90 kg (0–198 lb):
Front:
180 kPa (1.80 kgf/cm
2,
26 psi, 1.80 bar)
Rear:
200 kPa (2.00 kgf/cm
2,
29 psi, 2.00 bar)
90–196 kg (198–432 lb):
Front:
190 kPa (1.90 kgf/cm
2,
28 psi, 1.90 bar)
Rear:
230 kPa (2.30 kgf/cm
2,
33 psi, 2.30 bar)
Maximum load*:
196 kg (432 lb)
* Total weight of rider, passenger,
cargo and accessories
PERIODIC MAINTENANCE AND ADJUSTMENT
6-18
6
5WX-F8199-E3 7/11/08 16:51 Página 54

EWA10470
●Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the
vehicle with excessively worn
tires decreases riding stability
and can lead to loss of control.
●The replacement of all wheel
and brake related parts, inclu-
ding the tires, should be left to
a Yamaha dealer, who has the
necessary professional know-
ledge and experience.
EAU21960
Cast wheels
To maximize the performance, durabi-
lity, and safe operation of your vehi-
cle, note the following points regar-
ding the specified wheels.
●The wheel rims should be chec-
ked for cracks, bends or warpage
before each ride. If any damage
is found, have a Yamaha dealer
replace the wheel. Do not
attempt even the smallest repair
to the wheel. A deformed or crac-
ked wheel must be replaced.
●The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced.
An unbalanced wheel can result
in poor performance, adverse
handling characteristics, and a
shortened tire life.
●Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for
it to develop its optimal characte-
ristics.
EAU22020
Adjusting the clutch lever
free play
1. Clutch lever free play
2. Locknut
3. Clutch lever free play adjusting bolt
The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch
lever free play and, if necessary,
adjust it as follows.
1. Loosen the locknut at the clutch
lever.
2. To increase the clutch lever free
play, turn the adjusting bolt in
direction (a). To decrease the
clutch lever free play, turn the
adjusting bolt in direction (b).
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-19
6
5WX-F8199-E3 7/11/08 16:51 Página 55

3. Tighten the locknut.
TIP
If the specified free play cannot be
obtained as described above or if the
clutch does not operate correctly,
have a Yamaha dealer check the
internal clutch mechanism.
EAUT1221
Checking the front brake
lever free play
1. Front brake lever free play
The brake lever free play should mea-
sure 2.0–5.0 mm (0.08–0.20 in) as
shown. Periodically check the brake
lever free play and, if necessary, have
a Yamaha dealer check the brake sys-
tem.
EWA10641
An incorrect brake lever free play
indicates a hazardous condition in
the brake system. Do not operate
the vehicle until the brake system
has been checked or repaired by a
Yamaha dealer.
EAUM1353
Adjusting the brake pedal
free play
1. Brake pedal free play
The brake pedal free play should
measure 5.0–10.0 mm (0.20–0.39 in)
as shown. Periodically check the bra-
ke pedal free play and, if necessary,
have a Yamaha dealer adjust it.
EWAM1030
An incorrect brake pedal free play
indicates a hazardous condition in
the brake system. Do not operate
the motorcycle until the brake sys-
tem has been checked or repaired
by a Yamaha dealer.
WARNING
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-20
6
5WX-F8199-E3 7/11/08 16:51 Página 56