2010 MITSUBISHI GRANDIS lock

NOTE
l Only
open the bonnet when the wipers are in
the parked position. Failure to do so may
cause bonnet damage.
Support the bonnet by inserting the support bar in
its slot. CAUTION
l
Note
that the support bar may disengage
the bonnet if the open bonnet is lifted by
a strong wind.
l Always insert the support bar into the
hole provided specifically for this pur-
pose. Supporting the bonnet at any other
location could result in the support bar
slipping out and lead to an accident.
To close
Unlatch the support bar and clip it in its holder. Slowly lower the bonnet to a position about 30 cm
above the closed position, then let it drop.
NOTE
l If

this does not close the bonnet, release it
from a slightly higher position.
l Do not press down the bonnet hard with a
hand as it may damage the bonnet. CAUTION
l
Be
careful that hands or fingers are not
trapped when closing the bonnet.
l Before driving, make sure that the bon-
net is securely locked. An incompletely
locked bonnet can suddenly open while
driving. This can be extremely dangerous. Engine oil
E01000402237
To check and refill engine oil
Petrol-powered vehicles
Diesel-powered vehicles
(except for diesel particulate
filter models) Maintenance
8-04
8
Presented by http://mmc-manuals.ru/ \251

Engine coolant
E01000501361
To check the coolant level
A
translucent coolant reserve tank is located in the
engine compartment.
Petrol-powered vehicles
Check the coolant level in the reserve tank. The re-
serve tank lid (B) is equipped with a dipstick.

Remove the dipstick and wipe it with a clean cloth.
Reinsert the dipstick as far as it goes. Remove the
dipstick and read the coolant level, which should al-
ways be within the range “F” (FULL) or “L”
(LOW) while the engine is cold.
FULL
LOW To add coolant
The

cooling system is a closed system and normal-
ly the loss of coolant should be very slight. A no-
ticeable drop in the coolant level could indicate leak-
age. If this occurs, we recommend you to have the
system checked as soon as possible.
If the level should drop below the “L” (LOW) level
on the dipstick, add coolant to the reserve tank. Also, if the reserve tank is completely empty, re-
move

the radiator cap (A) and add coolant until the
level reaches the filler neck. WARNING
l Do
not open the radiator cap while the en-
gine is hot. The coolant system is under
pressure and any hot coolant escaping
could cause severe burns.
Anti-freeze
The
engine coolant contains an ethylene glycol anti-
corrosion agent. The cylinder head and water pump
housing are cast aluminium alloy, and periodic
changing of the engine coolant is necessary to pre-
vent corrosion of these parts.

Use “DIA QUEEN SUPER LONG LIFE COOL-
ANT” or equivalent.
MITSUBISHI Genuine Coolant has excellent pro-
tection against corrosion and rust formation of all
metals including aluminium and can avoid block-
ages in the radiator, heater, cylinder head, engine
block, etc.
Because of the necessity of this anti-corrosion
agent, the coolant must not be replaced with plain
water even in summer. The required concentration
of anti-freeze differs depending on the expected am-
bient temperature. Ambient
temperature (minimum) °C -15 -20 -25 -30 -35 -50 Anti-freeze
concentra- tion % 30 35 40 45 50 60 CAUTION
l
Do
not use alcohol or methanol anti-
freeze or any engine coolants mixed with
alcohol or methanol anti-freeze. The use
of an improper anti-freeze can cause cor-
rosion of the aluminium components.
l For effective anti-corrosion and anti-
freeze performance, keep the anti-freeze
concentration within the range of 30 to
60 %.
Concentrations exceeding 60 % will re-
sult in a reduction of both the anti-freeze
and cooling performance thus adversely
affecting the engine.
l Do not top up with water only.
Water by itself reduces the rust-protec-
tive and anti-freeze qualities of the cool-
ant and has a lower boiling point. It can
also cause damage to the cooling system if
it should freeze. Do not use tapwater, as it
can cause corrosion and rust formation. Maintenance
8-06
8
Presented by http://mmc-manuals.ru/ \251

Diesel-powered vehicles
The
coolant level in this tank should be kept be-
tween the “LOW” and “FULL” marks when meas-
ured while the engine is cold.
FULL
LOW To add coolant
The

cooling system is a closed system and normal-
ly the loss of coolant should be very slight. A no-
ticeable drop in the coolant level could indicate leak-
age. If this occurs, we recommend you to have the
system checked as soon as possible.
If the level should drop below the “LOW” level on
the reserve tank, open the lid and add coolant. WARNING
l Do
not open the reserve tank cap while
the engine is hot. The coolant system is un-
der pressure and any hot coolant escap-
ing could cause severe burns. Anti-freeze
The

engine coolant contains an ethylene glycol anti-
corrosion agent. The cylinder head and water pump
housing are cast aluminium alloy, and periodic
changing of the engine coolant is necessary to pre-
vent corrosion of these parts.

Use only “BASF Glysantin Alu Protect
Premium/G30”.
It has excellent protection against corrosion and
rust formation of all metals including aluminium
and can avoid blockages in the radiator, heater, cyl-
inder head, engine block, etc.
Because of the necessity of this anti-corrosion
agent, the coolant must not be replaced with plain
water even in summer.
The anti-freeze must fill 50 % concentration cool-
ant in all temperature conditions. CAUTION
l
Do
not use alcohol or methanol anti-
freeze or any engine coolants mixed with
alcohol or methanol anti-freeze. The use
of an improper anti-freeze can cause cor-
rosion of the aluminium components.
l Do not top up with water only.
Water by itself reduces the rust-protec-
tive and anti-freeze qualities of the cool-
ant and has a lower boiling point. It can
also cause damage to the cooling system if
it should freeze. Do not use tapwater, as it
can cause corrosion and rust formation. During cold weather
If

the temperatures in your area drop below freez-
ing, there is the danger that the coolant in the en-
gine or radiator could freeze and cause severe dam-
age to the engine and/or radiator. Add a sufficient
amount of anti-freeze to the coolant to prevent it
from freezing.
The concentration should be checked before the
start of cold weather and anti-freeze added to the
system if necessary. Maintenance
8-07 8
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
If the tyres have arrows (A) indicating
the correct direction of rotation, swap the
front and rear wheels on the left hand
side of the vehicle and the front and rear
wheels on the right hand side of the vehi-
cle separately. Keep each tyre on its origi-
nal side of the vehicle. When fitting the
tyres, make sure the arrows point in the
direction in which the wheels will turn
when the vehicle moves forward. Any
tyre whose arrow points in the wrong di-
rection will not perform to its full poten-
tial.
Front CAUTION
l
Avoid
the combined use of different types
of tyres.
Using different types of tyres can affect ve-
hicle performance and safety. Snow tyres
E01002000725
The

use of snow tyres is recommended for driving
on snow and ice. To preserve driving stability,
mount snow tyres of the same size and tread pat-
tern on all 4 wheels.
Snow tyres worn more than 50% are no longer suit-
able for use as snow tyres.
Snow tyres which do not meet specifications must
not be used. CAUTION
l
Observe
permissable maximum speed for
your snow tyres and the legal speed limit.
NOTE l The

laws and regulations concerning snow
tyres (driving speed, required use, type, etc.)
vary. Find out and follow the laws and regu-
lations in the area you intend to drive.
l If flange nuts are used on your vehicle,
change to tapered nuts when steel wheels are
used.
Tyre chains E01002101130
If tyre chains have to be used, ensure that they are
fitted only on the drive wheels (front).
Use

only tyre chains which are designed for use
with the tyres mounted on the vehicle: use of the in-
correct size or type of chain could result in damage
to the vehicle body.
Before fitting tyre chains, We recommend you to
consult a MITSUBISHI MOTORS Authorized Serv-
ice Point. Tyre size Wheel size Max chain
height[mm]
215/60R16 16x6.5 JJ 9
215/55R17 17x7.0 J The speed limit for tyre chain is 50 km/h (30

mph)
and remove the tyre chains as soon as possible on
snow free roads. WARNING
l DO
NOT use a jack when fitting the
chains, as in thsee conditions, the tyres
may slip on the icy road causing the vehi-
cle to slip off the jack. CAUTION
l
Practice
fitting the chains before you
need them.
Don’t expect help from other people in
the cold.
l Choose a clear straight stretch of road
where you can pull over and still be seen
while you are fitting the chains.
l Do not fit chains before you need them.
This will wear out your tyres and the
road surface.
l After driving around 100-300 metres,
stop and retighten the chains.
l Care should be taken with extremes of
steering lock to prevent possible contact
between the chains and the vehicle body. Maintenance
8-14
8
Presented by http://mmc-manuals.ru/ \251

Fuses
E01003001989
Fuse block location
To
prevent damage to the electrical system due to
shortcircuiting or overloading, each individual cir-
cuit is provided with a fuse.
There are fuse blocks in the passenger compart-
ment and in the engine compartment.
Passenger compartment
The fuse block in the passenger compartment is lo-
cated behind the fuse box lid (LHD vehicles) or the
personal box (RHD vehicles) in front of the driv-
er’s seat at the position shown in the illustration. Engine compartment
In

the engine compartment, the fuse block is loca-
ted as shown in the illustration.
Petrol-powered vehicles
Diesel-powered vehicles 1- Push the knob.
2-

Remove the cover.
Fuse load capacity
The fuse capacity and the name of the electrical sys-
tems protected by the fuses are indicated at the fuse
box lid (LHD vehicles) or the personal box (RHD
vehicles) and on the inside of the fuse block cover
for fuses located in the engine compartment.
Passenger compartment fuse location table
NOTE l Spare fuses are contained in the fuse box lid
(LHD vehicles) or the personal box lid
(RHD vehicles). Always use a fuse of the
same capacity for replacement. Maintenance
8-20
8LHD RHD
Presented by http://mmc-manuals.ru/ \251

Passenger compartment fuse location (LHD)Passenger compartment fuse location (RHD)No. Symbol Electrical system Capaci-
ties
1 Ignition coil 10 A
2 Gauge 7.5 A
3 Reversing lamp 7.5 A
4 Cruise control 7.5 A
5 Relay 7.5 A
6 Heated door mirror 7.5 A
7 Windscreen wiper 30 A No. Symbol Electrical system Capaci-
ties
8 Engine control 7.5 A
9 Accessory socket 15 A
10 — ——
11 Outside rear-view
mirrors 7.5 A
12 Engine control 7.5 A
13 — ——
14 Rear window wiper 15 A
15 Central door locks 15 A
16 Rear fog lamp 10 A
17 — ——
18 — ——
19 Heater 30 A
20 Rear window demis-
ter 30 A
21 Sunroof 20 A
22 Heated seat 20 A
23 Rear air conditioning 20 A
24 Starter 10 A
25 — Spare fuse 30 A
26 — Spare fuse 20 A
27 — Spare fuse 30 A Maintenance
8-21 8
Presented by http://mmc-manuals.ru/ \251

l
Some fuses may not be installed on your ve-
hicle, depending on the vehicle model or spec-
ifications.
l The table above shows the main equipment
corresponding to each fuse.
The fuse box does not contain spare 7.5 A,
10 A and 15 A fuses. If a fuse of one of these
capacities blows, replace it temporarily by
borrowing the one that matches from:
7.5 A: Outside rear-view mirrors
10 A: Radio (Engine compartment)
15 A: Accessory socket
Replace the borrowed fuse as soon as possible.
Engine compartment fuse location table
Engine compartment fuse location
Front No. Symbol Electrical system Capaci-
ties
1 —
—
—*1 Battery
60 A*2
2 Radiator fan motor
50 A
*1
40 A *2
3 Anti-lock brake sys-
tem 30 A
4 Anti-lock brake sys-
tem 40 A
5 Electric window sys-
tem 40 A
6 Front fog lamps 15 A
7 AC power supply
15 A*1 Accessory socket
Accessory socket
15 A*2
8 Horn 10 A
9 Engine control
20 A
*1
10 A *2
10 Air conditioning 10 A
*1 : Petrol-powered vehicles
*2 : Diesel-powered vehicles
*3 :

Vehicles without discharge headlamps: 55 W
(H1)
*4 : Vehicles with discharge headlamps: 35 W
(D2R) No. Symbol Electrical system Capaci-
ties
11 Stop lamps 15 A
12 Horn
15 A*1 Wiper de-icer
— —
—*2
13 Alternator
7.5 A*1 Starter
25 A*2
14 Hazard warning
flasher 10 A
15 Automatic transmis-
sion 20 A
*1
— —
—*2
16 Headlamp high-beam
(right) 10 A
17 Headlamp high-beam
(left) 10 A
18 Headlamp low beam
(right) 10 A
*3
20 A *4
19 Headlamp low beam
(left) 10 A
*3
20 A *4
*1 : Petrol-powered vehicles
*2 : Diesel-powered vehicles
*3 :
Vehicles without discharge headlamps: 55 W
(H1)
*4 : Vehicles with discharge headlamps: 35 W
(D2R) Maintenance
8-22
8
Presented by http://mmc-manuals.ru/ \251

No. Symbol Electrical system Capaci-
ties
20 Tail lamp (right) 7.5 A
21 Tail lamp (left) 7.5 A
22 Back up 15 A
23 Radio 10 A
24 Fuel pump 15 A
25 Electric tailgate
—*1
— —
—*2
*1 : Petrol-powered vehicles
*2 : Diesel-powered vehicles
*3 :
Vehicles without discharge headlamps: 55 W
(H1)
*4 : Vehicles with discharge headlamps: 35 W
(D2R) Engine compartment fuse location (diesel-pow-
ered vehicles only)
Engine compartment fuse location
Front No. Symbol Electrical system Capaci-
ties
1 Condenser fan 30 A
2 Engine control 30 A
3 Control flap 10 A
4 Glow relay 10 A
5 Valve block 10 A
6 Immobilizer 7.5 A
7 Heating pipe 10 A l
Some
fuses may not be installed on your ve-
hicle, depending on the vehicle model or spec-
ifications.
l The table above shows the main equipment
corresponding to each fuse.
Identification of fuse Capacity Colour
7.5 A Brown
10 A Red
15 A Blue
20 A Yellow
25 A Transparent
30 A Green (fuse type)/
Pink (fusible link type)
40 A Green
50 A Red
60 A Yellow (fusible link type) Maintenance
8-23 8
Presented by http://mmc-manuals.ru/ \251