Page 930 of 3039
Engine - V8 S/C 5.0L Petrol - Crankshaft Rear Seal
Removal and Installation
Special Tool(s)
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 12-May-2014
1. Refer to: Flexplate (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
2. 303-1442
Rear Crankshaft Seal Installer JLR-303-1622
Alignment Tool, Engine Rear Oil Seal
Page 985 of 3039
Engine - V8 S/C 5.0L Petrol - Flexplate
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. CAUTION: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Transmission - V8 5.0L Petrol/V8 S/C 5.0L Petrol (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8
S/C 5.0L Petrol, Removal).
4. CAUTIONS:
Install all the bolts finger tight before final tightening.
The bolts can only be used 3 times, mark the bolts
with a center punch. If 2 punch marks are visible, discard
the bolts.
Make sure that no components fall off during removal.
Install the bolts in the noted position.
NOTES:
Make sure the crankshaft and flexplate mating faces
are clean before installation.
Make sure that the crankshaft is not rotated.
Tighten the retaining bolts working diagonally.
Torque:
Stage 1:45 Nm Stage 2:90°
Installation
1. To install, reverse the removal procedure.
Page 993 of 3039
303-1442
Rear Crankshaft Seal Installer
303-1443
Rear Crankshaft Cover Alignment Tool Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is always correct. Published: 03-Dec-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.
Raise and support the vehicle.
3. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
4. Refer to: Engine (303-01D Engine - V8 S/C 5.0L Petrol, Installation).
Page 994 of 3039
5. CAUTIONS:
The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.
Make sure that no components fall off during removal.
NOTES:
Make sure that the crankshaft is not rotated.
Make sure the crankshaft and flexplate mating faces are clean before
installation.
6.
7.
8.
Page 1017 of 3039
49. CAUTIONS:
Install all the bolts finger tight before final tightening.
The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.
Install the bolts in the noted position.
NOTES:
Make sure that the crankshaft is not rotated.
Make sure the crankshaft and flexplate mating faces are clean before
installation.
Tighten the retaining bolts working diagonally.
Torque:
Stage 1:45 Nm Stage 2:90°
50. Refer to: Engine (303-01D Engine - V8 S/C 5.0L Petrol, Installation).
51. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
52. Lower the vehicle.
53. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
Page 1022 of 3039
6. NOTE: Tsubaki timing drive only.
Install the lower timing chain making sure the coloured
chain links align correctly with the fuel rail high-pressure
fuel pumps camshaft and crankshaft sprocket markings.
Page 1023 of 3039
7. CAUTION: Make sure that the tensioner spring is
correctly located.
NOTE: Tsubaki timing drive only.
Torque: 21 Nm
8. NOTE: INA timing drive only.
Install the lower timing chain making sure the coloured
chain links align correctly with the fuel rail high-pressure
fuel pumps camshaft and crankshaft sprocket markings.
Page 1025 of 3039
Engine - V8 S/C 5.0L Petrol - Timing Cover
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 12-Sep-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Accessory Drive Belt (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).
4. Refer to: Accessory Drive Belt Tensioner (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).
5. Refer to: Thermostat Housing - Vehicles With: Supercharger (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and
Installation).
6. Refer to: Valve Cover LH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
7. Refer to: Valve Cover RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
8. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
9. NOTE: Engine shown removed for clarity.
