2010 JAGUAR XFR diagram

DTC Description Possible Causes Action B115B-15
Driver Seat Heater -
Circuit short to battery
or open
Driver seat heater supply
circuit - short to power, open
circuit
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams
and check driver seat heater supply circuit for
short to power, open circuit B1175-13
Driver Door Ajar
Switch - Circuit open
Driver door ajar switch
signal circuit - open circuit
Refer to the electrical circuit diagrams and check
driver door ajar switch signal circuit for open
circuit B1176-13
Passenger Door Ajar
Switch - Circuit open
Passenger door ajar switch
signal circuit - open circuit
Refer to the electrical circuit diagrams and check
passenger door ajar switch signal circuit for open
circuit B1177-12
Screenwash Level
Switch - Circuit short
to battery
Screenwash level switch
signal circuit - short to
power
Refer to the electrical circuit diagrams and check
screenwash level switch signal circuit for short to
power B11C0-13
Driver Side Rear Door
Ajar Switch - Circuit
open
Left rear door ajar switch
signal circuit - open circuit
Refer to the electrical circuit diagrams and check
left rear door ajar switch signal circuit for open
circuit B11C1-13
Passenger Side Rear
Door Ajar Switch -
Circuit open
Right rear door ajar switch
signal circuit - open circuit
Refer to the electrical circuit diagrams and check
right rear door ajar switch signal circuit for open
circuit B1222-23
Master Lock/Unlock
Switch - Signal stuck
low
Master lock or unlock switch
digital input circuit - signal
stuck low
Refer to the electrical circuit diagrams and check
master lock and unlock switch digital input
circuits for short to ground, open circuit B1237-11
Gear Shift Module
Early Wake-up -
Circuit short to ground
Transmission shift module
wake-up control circuit -
short to ground
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams
and check transmission shift module wake-up
control circuit for short to ground B1237-12
Gear Shift Module
Early Wake-up -
Circuit short to battery
Transmission shift module
wake-up control circuit -
short to power
Refer to the electrical circuit diagrams and check
transmission shift module wake-up control circuit
for short to power B1237-13
Gear Shift Module
Early Wake-up -
Circuit open
Transmission shift module
wake-up control circuit -
open circuit
Refer to the electrical circuit diagrams and check
transmission shift module wake-up control circuit
for open circuit B123E-13
Crank Enable - Circuit
open
OK to crank signal circuit -
open circuit
Refer to the electrical circuit diagrams and check
OK to crank signal circuit for open circuit B1A85-96 Ambient Light Sensor
- Component internal
failure
Light sensor internal
electronic failure
Check and install a new sensor as required B1C45-13
Front Wiper Park
Position Switch -
Circuit open
Windshield wiper motor park
switch signal circuit - open
circuit
Refer to the electrical circuit diagrams and check
windshield wiper motor park switch signal circuit
for open circuit B1C45-23
Front Wiper Park
Position Switch -
Signal stuck low
Signal stuck low
Refer to the electrical circuit diagrams and check
front wiper park position switch input circuit for
short, open circuit B1C78-12
Powerwash Relay -
Circuit short to battery
Powerwash relay control
circuit - short to power
Refer to the electrical circuit diagrams and check
powerwash relay control circuit for short to power B1C78-14
Powerwash Relay -
Circuit short to ground
or open
Powerwash relay control
circuit - short to ground,
open circuit
Refer to the electrical circuit diagrams and check
powerwash relay control circuit for short to
ground, open circuit www.JagDocs.com

Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Climate
Control Module (HVAC)
Description and Operation

Climate Control Module


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:


If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty
Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new
module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Climate Control Module. For additional
diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.
For additional information, refer to: Climate Control System (412-00 Climate Control System - General Information, Diagnosis and Testing).

DTC Description Possible Causes Action B105A-01
Cabin Temperature
Sensor Fan -
General electrical
failure
Aspirator motor
diagnostic circuit -
short to ground, open
circuit
Aspirator fan
component failure
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check aspirator motor
diagnostic circuit for short to ground, open circuit B1081-00
Left Temperature
Damper Motor -
No sub type
information
Left hand blend stepper
motor internal or
external fault
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system B1081-49
Left Temperature
Damper Motor -
Internal electronic
failure
Left hand blend stepper
motor internal
electronic failure
Suspect the left hand blend stepper motor. Check and
install a new stepper motor as required, refer to the new
module/component installation note at the top of the DTC
Index B1082-00
Right Temperature
Damper Motor -
No sub type
information
Right hand blend
stepper motor internal
or external fault
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system

DTC Description Possible Causes Action B1082-49
Right Temperature
Damper Motor -
Internal electronic
failure
Right hand blend
stepper motor internal
electronic failure
Suspect the right hand blend stepper motor. Check and
install a new stepper motor as required, refer to the new
module/component installation note at the top of the DTC
Index B1083-01
Recirculation
Damper Motor -
General electrical
failure
RECIRC servo motor
circuits - short to
ground, power, open
circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check RECIRC servo motor
circuit for short to ground, power, open circuit B1085-00
Defroster Damper
Motor - No sub
type information
Defrost stepper motor
internal or external
fault
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system B1085-49
Defroster Damper
Motor - Internal
electronic failure
Defrost stepper motor
internal electronic
failure
Suspect the defrost stepper motor. Check and install a new
stepper motor as required, refer to the new
module/component installation note at the top of the DTC
Index B1086-00
Air Distribution
Damper Motor -
No sub type
information
Panel/foot stepper
motor internal or
external fault
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system B1086-49
Air Distribution
Damper Motor -
Internal electronic
failure
Panel/foot stepper
motor internal
electronic failure
Suspect the panel/foot stepper motor. Check and install a
new stepper motor as required, refer to the new
module/component installation note at the top of the DTC
Index B1087-88
LIN Bus "A" - Bus
off
LIN Bus power #1
circuit - open circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check LIN Bus power #1
circuit for open circuit B1088-88
LIN Bus "B" - Bus
off
LIN Bus power #2
circuit - open circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check LIN Bus power #2
circuit for open circuit B11ED-68
Electric Heater
Control Module -
Event information
Event information.
Electric heater - invalid
communication
message
Clear DTC. With engine coolant temperature low, set
climate temperature to high and re-test. If DTC remains in
isolation suspect the PTC heater, check and install a new
heater as required, refer to the new module/component
installation note at the top of the DTC Index. If additional
LIN related DTCs are logged refer to the Actions for these
DTCs B11ED-87
Electric Heater
Control Module -
Missing message
Electric heater -
missing communication
message
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system B11ED-96
Electric Heater
Control Module -
Component
internal failure
Component internal
failure
Suspect the PTC heater, check and install a new heater as
required, refer to the new module/component installation
note at the top of the DTC Index B11ED-98
Electric Heater
Control Module -
Component or
system over
temperature
Component or system
over temperature
Clear DTC. With engine coolant temperature low, set
climate temperature to high and re-test. If DTC remains
suspect the PTC heater, check and install a new heater as
required, refer to the new module/component installation
note at the top of the DTC Index B11EE-01
A/C Compressor -
General electrical
failure
Air conditioning
compressor clutch
solenoid circuits - short
to ground, power, open
circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check air conditioning
compressor clutch solenoid circuits for short to ground,
power, open circuit

DTC Description Possible Causes Action B11F0-11
Air Intake Damper
Position Sensor -
Circuit short to
ground
RECIRC servo motor air
intake feedback and 5
volt supply circuits -
short to ground
Refer to the electrical circuit diagrams and check RECIRC
servo motor air intake feedback and 5 volt supply circuits
for short to ground B11F0-15
Air Intake Damper
Position Sensor -
Circuit short to
battery or open
RECIRC servo motor air
intake feedback and
ground circuits - short
to power, open circuit
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to the electrical circuit diagrams and check RECIRC servo motor air intake feedback and ground circuits for short to power, open circuit B11F8-00
Left Outer Vent -
No sub type
information
Left outer IP vent
actuator internal or
external fault
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system B11F8-49
Left Outer Vent -
Internal electronic
failure
Left outer IP vent
actuator internal
electronic failure
Suspect the left outer IP vent actuator. Check and install a
new actuator as required, refer to the new
module/component installation note at the top of the DTC
Index B11F9-00
Left Inner Vent -
No sub type
information
Left inner IP vent
actuator internal or
external fault
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system B11F9-49
Left Inner Vent -
Internal electronic
failure
Left inner IP vent
actuator internal
electronic failure
Suspect the left inner IP vent actuator. Check and install a
new actuator as required, refer to the new
module/component installation note at the top of the DTC
Index B11FA-00
Right Inner Vent -
No sub type
information
Right inner IP vent
actuator internal or
external fault
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system B11FA-49
Right Inner Vent -
Internal electronic
failure
Right inner IP vent
actuator internal
electronic failure
Suspect the right inner IP vent actuator. Check and install a
new actuator as required, refer to the new
module/component installation note at the top of the DTC
Index B11FB-00
Right Outer Vent -
No sub type
information
Right outer IP vent
actuator internal or
external fault
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system B11FB-49
Right Outer Vent -
Internal electronic
failure
Right outer IP vent
actuator internal
electronic failure
Suspect the right outer IP vent actuator. Check and install a
new actuator as required, refer to the new
module/component installation note at the top of the DTC
Index B11FF-84
A/C Refrigerant
Pressure - Signal
below allowable
range
Signal below allowable
range. A/C System
Refrigerant Pressure
too low
This DTC can be logged by the system due to low ambient
temperature soak (below 3°C) reducing the pressure in the
refrigerant gas system. If the cabin temperature logged
along with the DTC at the time is below 10°C this could
indicate low temperature. If the air conditioning
performance is satisfactory and the in-cabin temperature is
below 10°C then it is likely that the system contains a
suitable amount of gas and the DTC is being recorded as
an effect of the low ambient temperature. If this is not the
case carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system. Refer
to the electrical circuit diagrams and check air conditioning
pressure sensor circuits for short, open circuit. Check for
correct charge weight B11FF-85
A/C Refrigerant
Pressure - Signal
above allowable
range
Signal above allowable
range. A/C System
Refrigerant pressure
too high
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check air conditioning
pressure sensor circuits for short, open circuit

DTC Description Possible Causes Action B1A59-11
Sensor 5 Volt
Supply - Circuit
short to ground
Air conditioning
pressure sensor or
RECIRC servo motor 5
volt supply circuits -
short to ground
Refer to the electrical circuit diagrams and check air
conditioning pressure sensor and RECIRC servo motor 5 volt
supply circuits for short to ground B1A59-13
Sensor 5 Volt
Supply - Circuit
open
Air conditioning
pressure sensor 5 volt
supply circuits - open
circuit
Refer to the electrical circuit diagrams and check air
conditioning pressure sensor 5 volt supply circuit for open
circuit B1A60-11
Pollution Sensor -
Hydrocarbon -
Circuit short to
ground
Pollution sensor
hydrocarbon input
circuit - short to ground
Refer to the electrical circuit diagrams and check pollution
sensor hydrocarbon input circuit for short to ground B1A61-11
Cabin Temperature
Sensor - Circuit
short to ground
In car temperature
sensor circuit - short to
ground
Refer to the electrical circuit diagrams and check In car
temperature sensor circuit for short to ground B1A61-15
Cabin Temperature
Sensor - Circuit
short to battery or
open
In car temperature
sensor circuit - short to
power, open circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check In car temperature
sensor circuit for short to power, open circuit B1A63-11 Right Solar Sensor
- Circuit short to
ground
Right sun load sensor
signal circuit - short to
ground
Refer to the electrical circuit diagrams and check right sun
load sensor signal circuit for short to ground B1A64-11 Left Solar Sensor
- Circuit short to
ground
Left sun load sensor
signal circuit - short to
ground
Refer to the electrical circuit diagrams and check left sun
load sensor signal circuit for short to ground B1A67-13
Sensor Ground -
Circuit open
Sensor ground circuits -
open circuit
Refer to the electrical circuit diagrams and check sensor
ground circuits for open circuit B1A69-01
Humidity Sensor -
General electrical
failure
Humidity sensor PWM
input circuit - short to
ground, power, open
circuit
Sensor component
failure
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check humidity sensor PWM
input circuit for short to ground, power, open circuit. Check
and install a new sensor as required B1B62-11
Pollution Sensor -
NOx - Circuit
short to ground
Pollution sensor NOx
input circuit - short to
ground
Refer to the electrical circuit diagrams and check pollution
sensor NOx input circuit for short to ground B1B71-11
Evaporator Temperature
Sensor - Circuit
short to ground
Evaporator temperature
sensor signal circuit -
short to ground
Refer to the electrical circuit diagrams and check evaporator
temperature sensor signal circuit for short to ground B1B71-15
Evaporator Temperature
Sensor - Circuit
short to battery or
open
Evaporator temperature
sensor signal circuit -
short to power, open
circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check evaporator
temperature sensor signal circuit for short to power, open
circuit B1B72-11
LIN Bus #1 Power
Supply Circuit -
Circuit short to
ground
Stepper motor circuit
LIN Bus #1 power
supply - short to
ground
Refer to the electrical circuit diagrams and check stepper
motor circuit LIN Bus #1 power supply for short to ground C1B14-13
Sensor Supply
Voltage A - Circuit
open
RECIRC servo motor 5
volt supply circuit -
open circuit
Refer to the electrical circuit diagrams and check RECIRC
servo motor 5 volt supply circuit for open circuit

DTC Description Possible Causes Action C1B15-13
Sensor Supply
Voltage B - Circuit
open
RECIRC servo motor
and EVAP sensor
ground circuits - open
circuit
Refer to the electrical circuit diagrams and check RECIRC
servo motor and EVAP sensor ground circuits for open
circuit P0530-11
A/C Refrigerant
Pressure Sensor A
Circuit - Circuit
short to ground
Air conditioning
pressure sensor signal
circuit - short to ground
Refer to the electrical circuit diagrams and check air
conditioning pressure sensor signal circuit for short to
ground P0530-15
A/C Refrigerant
Pressure Sensor A
Circuit - Circuit
short to battery or
open
Air conditioning
pressure sensor signal
circuit - short to power,
open circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check air conditioning
pressure sensor signal circuit for short to power, open
circuit U0010-88
Medium Speed
CAN
Communication
Bus - Bus off
Bus off
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system U0300-00
Internal Control
Module Software
Incompatibility -
No sub type
information
Invalid configuration
message is received
Re-configure the RJB using the manufacturer approved
diagnostic system. Clear the DTC and retest. If the DTC is
still logged suspect the climate control module, refer to the
new module/component installation note at the top of the
DTC Index U1A14-49
CAN Initialisation
Failure - Internal
electronic failure
Internal electronic
failure
Suspect the climate control module, check and install a
new module as required, refer to the new
module/component installation note at the top of the DTC
Index U3000-55
Control Module -
Not configured
Incorrect car
configuration data
received
Re-configure the RJB using the manufacturer approved
diagnostic system. Clear DTC and re-test. If the DTC
remains suspect the climate control module. Check and
install a new module as required, refer to the new
module/component installation note at the top of the DTC
Index U3000-87
Control Module -
Missing message
Missing message
Re-configure the RJB using the manufacturer approved
diagnostic system. Check climate control module for DTCs
and refer to the DTC Index. Carry out CAN network integrity
tests using the manufacturer approved diagnostic system.
If DTC remains suspect the climate control module. Check
and install a new module as required, refer to the new
module/component installation note at the top of the DTC
Index U3002-81
Vehicle
Identification
Number - Invalid
serial data
received
Vehicle/component
mis-match. Corrupt VIN
data being transmitted,
module previously
installed to other
vehicle
Check and install original/new module as required, refer to
the new module/component installation note at the top of
the DTC Index www.JagDocs.com

Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Digital Audio Broadcast Module (DABM)
Description and Operation

Digital Audio Broadcast Module (DABM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals


Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the
manufacturers approved diagnostic system


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required

The table below lists all diagnostic trouble codes (DTCs) that could be logged on the digital audio broadcast module, for
additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Information and Entertainment System (415-00 Information and Entertainment System -
General Information, Diagnosis and Testing).

DTC Description Possible Causes Action B11A4-11
L-Band Antenna -
Circuit short to
ground
Digital audio broadcast
L-band antenna circuit -
short circuit to ground
Refer to electrical circuit diagrams and check digital audio
broadcast L-band antenna circuit for short circuit to ground B11A4-15
L-Band Antenna -
Circuit short to
battery or open
Digital audio broadcast
L-band antenna circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check digital audio
broadcast L-band antenna circuit for short circuit to power,
open circuit, high resistance B11A5-11
Band 3 Antenna -
Circuit short to
ground
Digital audio broadcast
band 3 antenna circuit -
short circuit to ground
Refer to electrical circuit diagrams and check digital audio
broadcast band 3 antenna circuit for short circuit to ground B11A5-15
Band 3 Antenna -
Circuit short to
battery or open
Digital audio broadcast
band 3 antenna circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check digital audio
broadcast band 3 antenna circuit for short circuit to power,
open circuit, high resistance

Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Driver Door
Module/Passenger Door Module (DDM/PDM)
Description and Operation

Driver/Passenger Door Module (DDM/PDM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Driver/Passenger Door Modules
(DDM/PDM). For additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Driver Door Module (DDM) (419-10 Multifunction Electronic Modules, Diagnosis and
Testing).

DTC Description Possible Causes Action B108F-23
Cabin Lock/Unlock
Switch - Signal stuck low
Cabin lock/unlock switch signal
stuck
Switch pressed for longer than
20 seconds
Switch circuit short circuit to
power or ground
Switch failure
Check the switch operation and
serviceability. Refer to the electrical circuit
diagrams and check the switch circuit B109C-11
Front Courtesy Light -
Circuit short to ground
Short to ground
Refer to the electrical circuit diagrams and
test front courtesy light circuit for short to
ground B109C-15
Front Courtesy Light -
Circuit short to battery
or open
Short to power or open circuit
Refer to the electrical circuit diagrams and
test front courtesy light circuit for short to
power or open circuit B10EB-11
Driver Door Double
Locking Motor - Circuit
short to ground
Short to ground
Refer to the electrical circuit diagrams and
test driver door double locking motor circuit
for short to ground