2010 JAGUAR XFR door panel removal

Rear View Mirrors - Exterior Mirror
Removal and Installation

Removal Published: 11-May-2011


1. NOTE: Left-hand shown, right-hand similar.



























2. Refer to: Front Door Trim Panel (501-05, Removal and Installation).


3. NOTE: Left-hand shown, right-hand similar. www.JagDocs.com

3. WARNING: Do not allow the glass to drop.


NOTE: Left-hand shown, right-hand similar.
















4. For additional information, refer to: Front Door Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).


5. NOTE: Right-hand shown, left-hand similar.













6. TORQUE: 7 Nm

Glass, Frames and Mechanisms - Door Window Regulator Motor
Removal and Installation

Removal Published: 11-May-2011

1. Refer to: Front Door Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).


2. NOTE: Right-hand shown, left-hand similar.
















3. NOTE: Components removed for clarity. www.JagDocs.com

2. CAUTIONS:


Install all the bolts finger tight before final tightening.


Care must be taken not to damage the outer door
panel.

Install the retaining bolt 1 to the witness mark on
the body.
Torque:
1 1.9 Nm 2 5 Nm






















3. NOTE: Components removed for clarity.
4. NOTE: Right-hand shown, left-hand similar.
Torque: 1.5 Nm









5. Refer to: Front Door Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

Handles, Locks, Latches and Entry Systems - Front Door Latch
Removal and Installation

Removal Published: 04-Feb-2013

1. Refer to: Front Door Window Glass (501-11 Glass, Frames and Mechanisms, Removal and Installation).


2. NOTE: Left-hand shown, right-hand similar.

Refer to: Exterior Front Door Handle (501-14 Handles, Locks, Latches and Entry Systems, Removal and Installation).

3. Refer to: Front Door Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).


4. NOTE: Right-hand shown, left-hand similar.

NOTE: The illustration may indicate either hand of the service panel, the opposite hand will be similar.

Item Description 1 Front fender 2 Front door 3 Rear door 4 Front door skin panel 5 Rear door skin panel 6 Quarter panel 7 Rocker panel 8 Rocker panel front section (cut from rocker panel) 9 Rocker panel rear section (cut from rocker panel) 10 Rocker panel inner reinforcement 11 Rocker panel and b-pillar outer panel 12 B-pillar reinforcement 13 B-pillar inner panel 14 A-pillar outer panel 15 A-pillar reinforcement 16 Fender apron panel 17 Fender apron panel closing panel Time schedules, side panels

The following information shows the total time taken to install single panels and complete assemblies. This time includes
removal of Mechanical, Electrical and Trim, (MET), items, plus paint times based on Metallic Clear Over Base Paint, (blends to
adjacent panels are not included).

The times shown were generated by Thatcham, (the Motor Insurance Repair Research Centre), and are to be used as a guide
only.

Single panel times
Panel Description Hours Front fender L/H 8.9 Front fender R/H 9.1 Front door 8.8 Rear door 8.7 Front door skin panel 11.1 Rear door skin panel 10.8 Quarter panel L/H 23.2 Quarter panel R/H 24.2 Rocker panel L/H 19.6 Rocker panel R/H 19.9 Rocker panel front section L/H 18.5 Rocker panel front section R/H 18.8 Rocker panel rear section L/H 16.7 Rocker panel rear section R/H 16.8 Windshield glass remove and install 2.2 Rear window glass remove and install 1.7 Headliner remove and install 3.3 Instrument panel console remove and install 5.3 Combination panel replacement times

The following panel combination times show the total time to remove/install body panels, MET items and paint times based on
Metallic Clear Over Base Paint process, (blends to adjacent panels are not included).

Combination panel times
Panel Description Hours Front fender Front door Total Time L/H 12.7
R/H 12.9 Combination panel times
Panel Description Hours Rear door Quarter panel Rear window glass remove and install Headliner remove and install Total Time L/H 29.0
R/H 30.00

Ornamentation, Removal and Installation).

8. Remove the windshield glass.
For additional information, refer to: Windshield Glass (501-11 Glass, Frames and Mechanisms, Removal and Installation).

9. Remove the pedestrian protection hood actuator.
For additional information, refer to: Pedestrian Protection Hood Actuator LH (501-20C Pedestrian Protection System, Removal and Installation) / Pedestrian Protection Hood Actuator RH (501-20C Pedestrian Protection System, Removal and Installation).

10. Release and position the floor covering to one side.

11. Release and position the bulkhead insulating material to one side.

12. Release and position the inner rocker panel wiring harness to one side.

13. Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

14. Remove the underfloor splash shield.

15. If the right-hand A-pillar outer panel is to be repaired, release and
position the underfloor wiring harness to one side.

16. Remove the front fender.
For additional information, refer to: Front Fender (501-27 Front End Sheet Metal Repairs, Removal and Installation).

17. Remove the front door.
For additional information, refer to: Front Door (501-03 Body Closures, Removal and Installation).

18. Remove the upper and lower front door hinges.

19. Remove the hood.
For additional information, refer to: Hood (501-02 Front End Body Panels, Removal and Installation).

20. Remove the hood hinge.

26. NOTE: It may be necessary to temporarily seal the
opening whilst the foam cures, to prevent it encroaching
into the hood hinge area.
Apply expanding foam into the A-pillar as indicated.










27. Make sure that any open or exposed panel joints are suitably sealed
following this procedure.

28. The installation of associated panels and components is the reversal of
removal procedure.
Tighten the hood hinge bolts to 17 Nm.
Tighten the upper and lower front door hinges to 30 Nm.