2010 JAGUAR XFR seat

4. Remove the rear seat head restraint(s).
Lower both rear seats.
























5. NOTES:


The procedure must be carried out on both sides of
the seat.


Left-hand shown, right-hand similar.
Remove both rear seat bolsters.

6. CAUTION: Make sure no damage is caused to the vehicle trim
when removing the rear seat.
With assistance, remove the rear seat backrest.
Both rear seat backrests need to be in an upright
position but not latched for access to retaining bolts.








7. Release the backrest cover.
Release all 4 sides.










8. Remove the rear seat backrest hinge(s).














9. Remove the rear armrest retaining screw covers.

10.
11. Remove the rear armrest retaining screws.
Remove the 2 Torx screws.
















CAUTION: Make sure no damage is caused to the seat
trim when removing the seat armrest.
Remove the rear seat armrest.










12.
Release the rear seat backrest cover from the armrest aperture.
Release the 3 plastic retaining strips from the securing clips.

13. Remove the cappings from the rear head restraint retaining posts.
Release the rear backrest cover over the head restraint posts.

14. Remove the rear seat backrest cushion and cover from the rear seat
backrest.

15. Remove and discard the hog rings.
Remove the 36 hog rings securing the rear 60% seat
backrest cover to the backrest seat cushion.
Remove the 26 hog rings securing the rear 40% seat
backrest cover to the backrest seat cushion.










16. Remove the rear seat backrest cover.

Installation

1. NOTES:

Seating - Front Seat Height Adjustment Motor
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Make the air bag supplemental restraint system (SRS) safe.

Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).

2. Disconnect the battery ground cable.

Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

3. Remove the front seat.

Refer to: Front Seat (501-10 Seating, Removal and Installation).
4.
5.

(100-00 General Information, Description and Operation).

2. For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

3. For additional information, refer to: Front Seat (501-10 Seating, Removal and Installation).

4. For additional information, refer to: Front Safety Belt Buckle (501-20A Safety Belt System, Removal and Installation).

5.
6.

Safety Belt System, Removal and Installation).

12. For additional information, refer to: Front Seat (501-10 Seating, Removal and Installation).

13. For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

Instrument Panel and Console - Floor Console Side Trim Panel
Removal and Installation

Removal

NOTES: Published: 11-May-2011

LHD right-hand floor console side trim panel shown, LHD left-hand and both RHD floor console side trim panels are
similar.


Removal steps in this procedure may contain installation details.

1. Recline the front seats and move to the rear most position.


2. NOTE: When removing the component, some of the clips
may remain attached. These clips should be removed and
returned to their original positions in the instrument
panel.













3.
4.

Front safety belt retractor to seat track retaining bolt 40 30 - Front safety belt retractor retaining bolt 40 30 - Front safety belt D loop retaining bolt 40 30 - Front safety belt buckle retaining bolt 40 30 - Front safety belt shoulder height adjuster retaining bolts 25 18 - Rear centre safety belt retractor retaining bolts 40 30 - Rear safety belt long end retaining bolts 40 30 - Rear safety belt D loop retaining bolt 40 30 - Rear safety belt long end retaining bolt 40 30 - Rear safety belt buckle retaining bolts 40 30 -