Page 2363 of 3039
7. NOTE: If equipped.
Remove the front seat backrest thermo-electric device.
Disconnect the electrical connector.
8. Remove the front seat head restraint.
9. Remove the front seat head restraint motor.
For additional information, refer to: Front Seat Head Restraint Motor (501-10 Seating, Removal and Installation).
10. NOTE: Some variation in the illustrations may occur,
but the essential information is always correct.
Using a suitable tool, remove the front seat head restraint
guide sleeves.
Page 2364 of 3039
11. Remove the front seat backrest cushion and cover from the front seat
frame.
12.
13. Remove and discard the hog rings.
Remove the 22 hog rings.
Remove the front seat backrest cover.
Installation
1. NOTES:
Make sure that new hog rings are installed.
Use hog ring pliers to close the hog rings. Do not use any
other tool. The hog rings must be closed to overlap as
illustrated.
To install, reverse the removal procedure. www.JagDocs.com
Page 2365 of 3039
Seating - Front Seat Bolster
Removal and Installation
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is always correct. Published: 11-May-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. Refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).
Installation
3.
4. WARNING: The procedure must be carried out on both
sides of the seat.
CAUTION: Make sure that the clips are correctly
located.
1. To install, reverse the removal procedure.
Page 2366 of 3039
Seating - Front Seat Bolster Pump
Removal and Installation
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is always correct. Published: 11-May-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. Refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).
3.
Installation
1. To install, reverse the removal procedure.
Page 2372 of 3039
Description and Operation).
2. Remove the front seat.
Refer to: Front Seat (501-10 Seating, Removal and Installation).
3.
4.
Page 2374 of 3039
Description and Operation).
2. Refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).
3.
4.
Installation
1. To install, reverse the removal procedure.
2. If a new component has been installed, configure using Jaguar approved
diagnostic equipment. www.JagDocs.com
Page 2376 of 3039
Seating - Seat Base
Removal and Installation
Removal
WARNINGS: Published: 11-May-2011
To avoid accidental deployment, the restraints control module backup power supply must be depleted. Wait at least one
minute after disconnecting the battery ground cable(s) before commencing any repair or adjustment to the supplemental
restraint system (SRS), or any component(s) adjacent to the SRS sensors. Failure to follow these instructions may result in
personal injury.
Always wear safety glasses when working on an air bag equipped vehicle and when handling an air bag module. Failure to
follow this instruction may result in personal injury.
To minimize the possibility of premature deployment, do not use radio key code savers when working on the
supplemental restraint system. Failure to follow this instruction may result in personal injury.
To minimize the possibility of injury in the event of premature deployment, always carry a live air bag module with the
bag and trim cover pointed away from the body. Failure to follow this instruction may result in personal injury.
To minimize the possibility of premature deployment, live air bag modules must only be placed on work benches which
have been ground bonded and with the trim cover facing up. Failure to follow these instructions may result in personal injury.
Never probe the electrical connectors of air bag modules or any other supplemental restraint system component. Failure
to follow this instruction may result in personal injury.
Painting over the driver air bag module trim cover or instrument panel could lead to deterioration of the trim cover and air
bags. Do not for any reason attempt to paint discolored or damaged air bag module trim covers or instrument panel. Install a
new component. Failure to follow this instruction may result in personal injury.
NOTES:
Some variation in the illustrations may occur, but the essential information is always correct.
Removal steps in this procedure may contain installation details.
1. Make the air bag supplemental restraint system (SRS) safe.
Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).
2. Refer to: Front Seat (501-10 Seating, Removal and Installation).
3. Refer to: Front Safety Belt Buckle (501-20A Safety Belt System, Removal and Installation).
4. Refer to: Front Seat Cushion Cover (501-10 Seating, Removal and Installation).
Page 2379 of 3039
Removal and Installation).
2. Release both the rear seat back rest catches.
3. Fold down the rear seat backrest. www.JagDocs.com
