2010 JAGUAR XFR seat

DTC Description Possible Causes Action U2101-00 Control module
Compatible central car
Using the manufacturer approved diagnostic Configuration Incompatible - No sub configuration file not system check and update the car configuration file type information received by front seat as required. Carry out on demand self test using climate control module manufacturer approved diagnostic system to confirm rectification. Clear the DTC and retest U3000-04
Control Module -
System internal
failures
Front seat climate control
module - Internal failure
Check and install new front seat climate control
module as required. Carry out on demand self test
using manufacturer approved diagnostic system to
confirm rectification U3003-62
Battery Voltage -
Signal compare failure
Wiring harness fault
Battery internal failure
Charging system fault
Refer to the electrical circuit diagrams and check
the power and ground connections to the front
seat climate control module and the central
junction box
Refer to the battery care manual and verify that
the vehicle battery is fully charged and serviceable
before continuing with further diagnostic tests
Check the vehicle charging system

Seating - Seat Smoothing
General Procedures Published: 01-May-2014



WARNINGS: Check

Make sure that the steamer is in the OFF position before connecting or disconnecting from the electrical outlet.
Do not use another high wattage device on the same electrical circuit.
If the use of an extension cord is absolutely necessary, the cord must be rated at a minimum of 10 amps.
To avoid the risk of electrical shock, check the condition of the power cord and the steamer before use.
Make sure that the steamer is disconnected from the electrical outlet before filling or emptying the water reservoir.
The steamer must only be used and placed on its stand on a stable surface.
To prevent injury such as burns, take care whilst using the steamer. Avoid coming into contact with the hot surface of the
steamer and do not direct steam toward any persons.


The steamer must ALWAYS be switched off when not in use or left unattended.


Do not allow the power cord to come into contact with the hot surface of the steamer.

CAUTIONS:


Protect the surrounding paintwork to avoid damage.
Protect the paintwork during this operation.
Do not use any additives in the steamer. Damage to the steamer or the seat cover can result if used.


NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

1. CAUTIONS:

Steam the leather cushions evenly and progressively. Do not use
excessive force.

Take care not to damage the leather whilst steaming into the
corners.

Do not hold the steamer in one place for longer than 10 seconds,
as this will burn the leather and damage the covers. www.JagDocs.com

Seating - Front Seat
Removal and Installation Published: 11-May-2011

Removal

1. Make the air bag supplemental restraint system (SRS) safe.
For additional information, refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).


2. NOTE: Right-hand shown, left-hand similar.

Position the front seat fully forwards.
Lower the front seat head restraint to the fully
lowered position.




















3. NOTE: Right-hand shown, left-hand similar.
Remove the safety belt lower anchor trim panel.

4. NOTE: Right-hand shown, left-hand similar. Release the
safety belt lower anchor from the front seat.





















5. NOTES:


Left-hand shown, right-hand similar.


Some variation in the illustrations may occur, but the
essential information is always correct.
Remove the 2 rear bolts from the front seat.







6. Position the front seat fully rearwards.


7. NOTE: Left-hand shown, right-hand similar.
Remove the 2 front bolts from the front seat.










8. Reposition the front seat to the central position.

9. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

10. Disconnect the front seat harness electrical connectors.
Tilt the front seat rearwards to aid disconnecting the
front seat electrical connectors.












11. NOTES:


Make sure no damage is caused to the vehicle trim when
removing the front seat.


Left-hand shown, right-hand similar.
Remove the front seat.






Installation

1. To install, reverse the removal procedure.
TORQUE: 47 Nm













2. NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.
TORQUE: 47 Nm

Seating - Front Seat Backrest
Removal and Installation Published: 11-May-2011

Removal

1. Make the air bag supplemental restraint system (SRS) safe.
For additional information, refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).

2. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

3. Remove the front seat.
For additional information, refer to: Front Seat (501-10 Seating, Removal and Installation).


4. WARNING: This step requires the aid of another
technician.


CAUTION: Take extra care when handling the
component.
Remove the front seat backrest assembly.






















5. Remove the front seat backrest cover.
For additional information, refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).

6. Remove the backrest halo panel.
Release the 5 wiring harness clips.


7. NOTE: Do not disassemble further if the component is removed for
access only.
Remove the front seat recliner motor.
For additional information, refer to: Front Seat Recliner Motor (501-10,

Removal and Installation).

8. Remove the lumbar assembly.
For additional information, refer to: Lumbar Assembly (501-10 Seating, Removal and Installation).

9. Remove the front seat head restraint motor.
For additional information, refer to: Front Seat Head Restraint Motor (501-10 Seating, Removal and Installation).

Installation

1. To install, reverse the removal procedure.
TORQUE: 35 Nm













2. If a new component has been installed, configure using Jaguar approved
diagnostic equipment.

Seating - Front Seat Backrest Cover
Removal and Installation
Removal Published: 11-May-2011

1. Make the air bag supplemental restraint system (SRS) safe.
For additional information, refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).

2. Remove the front seat.
For additional information, refer to: Front Seat (501-10 Seating, Removal and Installation).

3. Remove the side air bag module.
For additional information, refer to: Side Air Bag Module (501-20B Supplemental Restraint System, Removal and Installation).


4. NOTE: If equipped.
Reposition the front seat backrest thermo-electric device.














5. NOTE: If equipped.
Release the front seat backrest thermo-electric device duct











6. NOTE: If equipped.

Remove the front seat backrest thermo-electric device
retaining screws.