2010 JAGUAR XFR diagram

DTC Description Possible Causes Action check CAN Network B100D-87
Column Lock
Authorisation -
Missing message
Missing message
CAN fault
No response from
electric steering column
lock control module,
instrument cluster,
central junction box
Battery voltage at
electric steering column
lock control module too
low
Electric steering column
lock control module,
instrument cluster,
central junction box fault
NOTE: Prior to clearing this DTC, carry out the Vehicle
Functional Reset application using the manufacturer approved
diagnostic system

Clear DTC, repeatedly lock and unlock car using the key
fob and retest. Check for related DTCs and refer to the
relevant DTC index
If the fault is cleared, notify the customer that the
steering column lock may fail to unlock if the vehicle is
parked with a high steering angle or with the road wheel
against a curb. If the column lock is failing to disengage,
the customer may be able to rectify this by rotating the
steering wheel while pressing the engine start button
If fault persists, complete a CAN network integrity test
using the manufacturers approved diagnostic system.
Alternatively, refer to the electrical circuit diagrams and
check CAN circuits between the central junction box, the
instrument cluster and the electronic steering column
lock. Refer to the electrical circuit diagrams and check the
central junction box, the instrument cluster and the
electronic steering column lock power and ground supply
circuits for short circuit to ground, short circuit to power,
open circuit, high resistance. Repair circuit(s) as required.
Clear DTC, perform an on demand self-test and retest
If fault persists, check that the vehicle battery supply
voltage is between 9-16 volts. Rectify as required U0001-88
High Speed CAN
Communication
Bus - Bus off
Bus off
Refer to the electrical circuit diagrams and check the
power and ground connections to the module. Using the
manufacturer approved diagnostic system, complete a
CAN network integrity test. Refer to the electrical circuit
diagrams and check the CAN network U0300-00
Internal Control
Module Software
Incompatibility -
No sub type
information
No sub type information
Refer to network communication section of the workshop
manual. Clear the DTC and ensure the vehicle battery
supply voltage is between 9-16Volts. Using the
manufacturers approved diagnostic system, complete a
CAN integrity test. Perform an on demand self-test and
retest U3000-49
Control Module -
Internal electronic
failure
Internal electronic
failure detected during
self test or lock/unlock
operation
Refer to network communication section of the workshop
manual. Clear the DTC and ensure the vehicle battery
supply voltage is between 9-16Volts. Perform an on
demand self-test and if the DTC returns suspect the
electric steering column lock, refer to the warranty policy
and procedures manual if a module/component is suspect U3000-87
Control Module -
Missing message
Configuration message
not received
Refer to the electrical circuit diagrams and check the
power and ground connections to the module. Using the
manufacturer approved diagnostic system, complete a
CAN network integrity test. Refer to the electrical circuit
diagrams and check the CAN network. Check modules are
configured correctly using the manufacturer approved
diagnostic system U3002-81
Vehicle
Identification
Number - Invalid
serial data
received
Invalid vehicle
identification number
Confirm the correct VIN details are stored in Steering
Column Lock Module using the approved diagnostic
system

Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Television
Module (TVM)
Description and Operation

Television Control Module (TVCM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:


If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty
Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new
module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Television Control Module (TVCM). For
additional diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.
For additional information, refer to: Information and Entertainment System (415-00 Information and Entertainment System - General Information, Diagnosis and Testing).

DTC Description Possible Causes Action B1A56-11
Antenna - Circuit
short to ground
Antenna circuit
short to ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna circuit for short to ground B1A56-12
Antenna - Circuit
short to battery
Antenna circuit
short to power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna circuit for short to power B1A56-13
Antenna - Circuit
open
Antenna circuit
open circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna circuit for open circuit B1D55-11
Antenna#2 - Circuit
short to ground
Antenna #2
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #2 circuit for short to
ground B1D55-12
Antenna#2 - Circuit
short to battery
Antenna #2
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #2 circuit for short to power

DTC Description Possible Causes Action B1D55-13
Antenna#2 - Circuit
open
Antenna #2
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #2 circuit for open circuit B1D56-11
Antenna #3 Circuit -
Circuit short to
ground
Antenna #3
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for short to
ground B1D56-12
Antenna #3 Circuit -
Circuit short to
battery
Antenna #3
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for short to power B1D56-13
Antenna #3 Circuit -
Circuit open
Antenna #3
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for open circuit B1D57-11
Antenna #4 Circuit -
Circuit short to
ground
Antenna #4
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for short to
ground B1D57-12
Antenna #4 Circuit -
Circuit short to
battery
Antenna #4
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for short to power B1D57-13
Antenna #4 Circuit -
Circuit open
Antenna #4
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for open circuit B1D58-11 Television Output -
Circuit short to
ground
Television output
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for short to
ground B1D58-12 Television Output -
Circuit short to
battery
Television output
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for short to
power B1D58-13 Television Output -
Circuit open
Television output
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for open
circuit U3000-49
Control Module -
Internal electronic
failure
Internal
electronic failure
Suspect the television module, check and install a new module
as required, refer to the new module/component installation
note at the top of the DTC Index U3003-16
Battery Voltage -
Circuit voltage below
threshold
Circuit voltage
below threshold
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system U3003-17
Battery Voltage -
Circuit voltage above
threshold
Circuit voltage
above threshold
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system

DTC Description Possible Causes Action C1A64-68
Spare Wheel Tire
Pressure Sensor and Transmitter Assembly -
Event information
Information only - vehicle
exposed to extreme
temperature environment
and/or tire pressure
sensor low battery
voltage event
No action required C1A64-91
Spare Wheel Tire
Pressure Sensor and Transmitter Assembly -
Parametric
Tire pressure sensor has
reported out of range
information for pressure,
temperature or
acceleration
Replace defective tire pressure sensor, refer to
the relevant section of the workshop manual C1A64-93
Spare Wheel Tire
Pressure Sensor and Transmitter Assembly -
No operation
Missing, incompatible or
defective tire pressure
sensor or radio frequency
receiver
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test H in section 204-04,
Diagnosis and Testing, Wheels and Tires C1D19-11
External Receiver Data
Line - Circuit short to
ground
Tire pressure monitoring
system radio frequency
receiver or data line
circuit is short to ground
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test A in section
204-04,Diagnosis and Testing, Wheels and Tires C1D19-12
External Receiver Data
Line - Circuit short to
battery
Tire pressure monitoring
system radio frequency
receiver or data line
circuit is short to power
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test I in section 204-04,
diagnosis and testing C1D19-87
External Receiver Data
Line - Missing message
Radio Frequency
reception blocked
Tire pressure monitoring
system radio frequency
receiver faulty
Tire pressure monitoring
system radio frequency
receiver or data line
circuits open circuit
Missing, incompatible or
defective tire pressure
sensors
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test J in section 204-04,
Diagnosis and Testing, Wheels and Tires U0010-88
Medium Speed CAN
Communication Bus - Bus
off
CAN bus fault
Carry out CAN network integrity tests. Refer to
the electrical wiring diagrams and check CAN
network for short, open circuit U0140-00
Lost communication with
body control module - No
sub type information
CAN bus fault
Central junction box fault
Refer to the electrical wiring diagrams and check
central junction box power and ground supplies
for short, open circuit. Carry out CAN network
integrity tests U0142-00
Lost Communication With
Body Control Module "B" -
No sub type information
CAN bus fault
Rear junction box fault
Refer to the electrical wiring diagrams and check
rear junction box power and ground supplies for
short, open circuit. Carry out CAN network
integrity tests U0155-00
Lost Communications
With Instrument Panel
Cluster (IPC) Control
Module - No sub type
information
CAN bus fault
Instrument cluster fault
Refer to the electrical wiring diagrams and check
instrument cluster power and ground supplies for
short, open circuit. Carry out CAN network
integrity tests U0164-00
Lost Communication With
HVAC Control Module - No
sub type information
CAN bus fault
Climate control module
fault
Refer to the electrical wiring diagrams and check
climate control module power and ground supplies
for short, open circuit. Carry out CAN network
integrity tests

Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Touch
Screen Display (FCDIM)
Description and Operation

Touch Screen (TS)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:


If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty
Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new
module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Touch Screen (TS). For additional
diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.
For additional information, refer to: Information and Entertainment System (415-00 Information and Entertainment System - General Information, Diagnosis and Testing).

DTC Description Possible Causes Action B100E-25
Video Input 'A' - Signal
shape/waveform
failure
ODST Only - TV video
synch mis-match
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B100F-25
Video Input 'B' - Signal
shape/waveform
failure
ODST Only - Reverse
Camera video synch
mis-match
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system U1A01-01
Communication Link -
General electrical
failure
ODST Only - cable
from navigation
module not correctly
installed
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system.
Check electrical harness from navigation module is
correctly installed U1A01-15
Communication Link -
Circuit short to battery
or open
TSD to navigation
module circuit - short
to power, open circuit
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check TSD to
navigation module circuit for short to power, open circuit U1A4B-48
Control Module
Processor B -
Supervision software
failure
Supervision software
failure
Re-configure the TSD using the manufacturer approved
diagnostic system www.JagDocs.com

DTC Description Possible Causes Action P0561-1C System Voltage Unstable
- Circuit voltage out of
range
Power supply voltage out
of range when engine
running
Check Engine Control Module for stored DTCs.
Check Charging System and Battery condition P0562-21
System Voltage Low -
Signal amplitude <
minimum
Circuit low voltage.
Battery supply voltage to
Transmission Control
Module
Refer to Circuit diagrams and check Power and
Ground Circuit for fault. Check Engine Control
Module for stored DTCs. Check Charging System
and Battery condition P0563-22
System Voltage High -
Signal amplitude >
maximum
High Battery charge,
alternator fault
Check Engine Control Module for stored DTCs.
Check Charging System and Battery condition P0601-41
Internal Control Module
Memory Check Sum Error
- General checksum
failure
Software error
Transmission Control
Module failure
Re-configure the Transmission Control Module
using the manufacturer approved diagnostic
system, clear DTC and re-test. If DTC remains,
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0604-00
Internal Control Module
Random Access Memory
(RAM) Error - No sub type
information
Shift-by-Wire fault
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0605-41
Internal Control Module
Read Only Memory (ROM)
Error - General checksum
failure
General checksum failure
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0606-04 TCM Processor - System
Internal Failures
Micro controller
component faults
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0606-26 TCM Processor - Signal
rate of change below
threshold
Micro controller
component faults
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0606-49 TCM Processor - Internal
electronic failure
Micro controller
component faults
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0613-04 TCM Processor - System
Internal Failures
Micro controller
component faults
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0613-06 TCM Processor -
Algorithm Based Failures
Micro controller
component faults
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0613-11 TCM Processor - Circuit
Short to Ground
Watchdog fault
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0613-12 TCM Processor - Circuit
Short to Battery
Watchdog fault
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect.

DTC Description Possible Causes Action P0657-1C
Actuator Supply Voltage
A Circuit / Open - Circuit
voltage out of range
Actuator supply (pressure
control valves etc)
voltage plausibility fault
Refer to electrical Circuit diagrams and check
Transmission Control Module connector for signs of
water ingress or damage, check pin 7 for Short to
Power or Ground (should NOT be connected and
harness terminal should have a bung installed). If
no fault identified, suspect the Transmission
Control Module. Check and install a new
Transmission Control Module as required, refer to
the warranty policy and procedures manual if a
module/component is suspect. P0658-11
Actuator Supply Voltage
A Circuit Low - Circuit
Short to Ground
Actuator supply (pressure
control valves etc)
voltage Short to Ground
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0659-12
Actuator Supply Voltage
A Circuit High - Circuit
Short to Battery
Actuator supply (pressure
control valves etc)
voltage Short to Power
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0667-01
PCM / ECM / TCM Internal Temperature Sensor A
Range/Performance -
General Electrical Failure
General electrical failure
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0667-04
PCM / ECM / TCM Internal Temperature Sensor A
Range/Performance -
System Internal Failures
Internal Electronic Failure
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0667-49
PCM / ECM / TCM Internal Temperature Sensor A
Range/Performance -
Internal electronic failure
Internal electronic failure
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0700-02 Transmission Control
System (MIL Request) -
General signal failure
General Signal failure
Clear DTC, Road test and re-test, Read DTCs and
Investigate as required P0700-22 Transmission Control
System (MIL Request) -
Signal amplitude >
maximum
Double fault from
monitoring of internal
power supply and
pressure
regulator/solenoid control
software
If any of the following DTCs are also present;
P074013, P096712, P273912, P273012, P272112,
P096312, P276312, P097112, suspect the
Transmission Control Module, check and install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0700-75 Transmission Control
System (MIL Request) -
Emergency Position Not
Reachable
Emergency Position Not
Reachable
Clear DTC, Road test and re-test, Read DTCs and
investigate as required P0710-13 Transmission Fluid Temperature Sensor A
Circuit - Circuit Open
Transmission fluid
temperature sensor
Circuit Open Circuit
Clear DTC and test. If code re-detects suspect the
Transmission Control Module. Install a new
Transmission Control Module as required, refer to
the warranty policy and procedures manual if a
module/component is suspect. P0711-01 Transmission Fluid Temperature Sensor A
Circuit
Range/Performance -
General Electrical Failure
General electrical failure
Clear DTC and test. If code re-detects suspect the
Transmission Control Module. Install a new
Transmission Control Module as required, refer to
the warranty policy and procedures manual if a
module/component is suspect. P0711-22 Transmission Fluid Temperature Sensor A
Circuit
Range/Performance -
Signal amplitude >
maximum
Signal amplitude >
maximum. Excessive
jump in temperature
Clear DTC. Carry out cold start road test, continue
driving vehicle until normal operating temperature
is achieved. Reads DTCs, if DTC returns, suspect
the Transmission Control Module. Install a new
Transmission Control Module as required, refer to

DTC Description Possible Causes Action suspect. P0783-77
3-4 Shift - Commanded
position not reachable
Gear Ratio Monitoring.
Mechanical Failures
Check and correct oil level. Clear DTC. If code
re-detects suspect Transmission (mechanical)
internal fault. Install a new Transmission as
required, refer to the warranty policy and
procedures manual if a module/component is
suspect. P0784-07
4-5 Shift - Mechanical
Failures
Gear Ratio Monitoring.
Mechanical Failures
Check and correct oil level. Clear DTC. If code
re-detects suspect Transmission (mechanical)
internal fault. Install a new Transmission as
required, refer to the warranty policy and
procedures manual if a module/component is
suspect. P0784-77
4-5 Shift - Commanded
position not reachable
Gear Ratio Monitoring.
Mechanical Failures
Check and correct oil level. Clear DTC. If code
re-detects suspect Transmission (mechanical)
internal fault. Install a new Transmission as
required, refer to the warranty policy and
procedures manual if a module/component is
suspect. P0798-1A
Pressure Control Solenoid
C Electrical - Circuit
Resistance Below Threshold
Pressure control solenoid
C Circuit resistance below
threshold
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0798-1E
Pressure Control Solenoid
C Electrical - Circuit Short
to Ground
Pressure control solenoid
C electrical circuit short
to ground
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0798-21
Pressure Control Solenoid
C Electrical - Signal
amplitude < minimum
Pressure Control Solenoid
C Electrical signal
amplitude < minimum
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0814-62 Transmission Range
Display Circuit - Signal
compare failure
Transmission Range
Display Circuit signal
compare failure
Suspect the Transmission Control Module. Install a
new Transmission Control Module as required,
refer to the warranty policy and procedures manual
if a module/component is suspect. P0826-08
Up and Down Switch
circuit - Bus Signal
Message Failures
Invalid CAN signal from
Central Junction
Box/Instrument Cluster
Stuck Sprintronic switch
CAN bus circuit fault
Check Central Junction Box and Instrument Cluster
for stored DTCs. Check gear change switches for
correct operation. Refer to circuit diagrams and
check CAN bus for a circuit fault P0826-81
Up and Down Switch
Circuit - Invalid serial
data received
Invalid Can signal from
Central Junction Box /
Instrument Cluster
Stuck Sprintronic switch
CAN Bus Circuit fault
Check Central Junction Box and Instrument Cluster
for stored DTCs. Check Gear Change Switches for
correct operation. Refer to Circuit diagrams and
check CAN Bus for Circuit fault P0826-88
Up and Down Switch
Circuit - Bus off
Steering Wheel Module to
Central Junction Box /
Instrument Cluster LIN
Bus failure
Check Central Junction Box and Steering Wheel
Ice Switches for stored DTCs. Refer to Circuit
diagrams and check LIN Bus for Circuit fault P0829-07
5-6 Shift - Mechanical
Failures
Gear Ratio Monitoring.
Mechanical Failures
Check and correct oil level. Clear DTC. If code
re-detects suspect Transmission (mechanical)
internal fault. Install a new Transmission as
required, refer to the warranty policy and
procedures manual if a module/component is
suspect. www.JagDocs.com