2010 JAGUAR XFR brake

Published: 11-May-2011
Parking Brake and Actuation - Parking Brake Cable Tension Release
General Procedures

Special Tool(s)


Electric parking brake release tool 206-082. Only to be used for EMERGENCY brake
release

Electric parking brake release tool link lead 206-082-01. Only to be used for EMERGENCY brake
release
WARNING: Failure to release the tension and calibrate the electric parking brake during rear parking brake related service
procedures, could cause the parking brake to function incorrectly or become inoperative.


1. WARNING: Always use Jaguar approved diagnostic equipment to
release the cable tension, when carrying out repair operations on the
electric park brake which require cable tension release.

Connect the Jaguar approved diagnostic equipment to release the
electric parking brake cable tension.
Follow the on-screen instructions.


2. WARNING: The procedure below should only be used in emergency
situations, to release the electric park brake. All calibration of the
parking brake system will be lost, and the parking brake will need to be
re-calibrated to function correctly.


NOTE: The tools shown must only be used in the event of an
emergency.
Remove the RH loadspace trim panel.
For additional information, refer to: Loadspace Trim Panel RH (501-05 Interior Trim and Ornamentation, Removal and Installation). www.JagDocs.com

3. WARNING: Failure to follow this instruction may result in a
diagnostic trouble code (DTC) being generated.

Disconnect the 2 electrical connectors from the parking
brake module, in the sequence illustrated.




















4. NOTE: Some variation in the illustrations may occur,
but the essential information is always correct.

Connect the special tool to the parking brake module.










5. Release the parking brake cable tension.
An audible 'click', signals complete parking brake cable
tension release.











6. Remove the special tool and carry out any necessary repairs on the
system.

7. Connect the electrical connectors in the sequence shown.




















8. Install the RH loadspace trim panel.
For additional information, refer to: Loadspace Trim Panel RH (501-05 Interior Trim and Ornamentation, Removal and Installation).


9. WARNING: Calibrate the electric park brake using Jaguar approved
diagnostic equipment. If Jaguar approved diagnostic equipment is not
available disconnect the battery for approximatly 30 seconds , the
vehicle will then prompt the driver to carry out the calibration procedure
as per the vehicle hand book on re-connection.
Calibrate the electric park brake.

Published: 12-Jun-2013
Parking Brake and Actuation - Parking Brake Cable LH TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol
Removal and Installation

Removal


WARNING: Failure to release the tension and calibrate the electric parking brake during rear parking brake related service
procedures, could cause the parking brake to function incorrectly or become inoperative.


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Parking Brake Cable Tension Release (206-05 Parking Brake and Actuation, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Rear Subframe - TDV6 3.0L Diesel (502-00 Uni-Body, Subframe and Mounting System, Removal and Installation).
Refer to: Rear Subframe - V8 5.0L Petrol/V8 S/C 5.0L Petrol (502-00 Uni-Body, Subframe and Mounting System, Removal and Installation).

4.

Published: 12-Jun-2013
Parking Brake and Actuation - Parking Brake Cable RH TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol
Removal and Installation

Removal


WARNING: Failure to release the tension and calibrate the electric parking brake during rear parking brake related service
procedures, could cause the parking brake to function incorrectly or become inoperative.


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Parking Brake Cable Tension Release (206-05 Parking Brake and Actuation, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Rear Subframe - TDV6 3.0L Diesel (502-00 Uni-Body, Subframe and Mounting System, Removal and Installation).
Refer to: Rear Subframe - V8 5.0L Petrol/V8 S/C 5.0L Petrol (502-00 Uni-Body, Subframe and Mounting System, Removal and Installation).

4.
5. NOTE: Note the fitted position. www.JagDocs.com

Parking Brake and Actuation - Parking Brake Module
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Loadspace Trim Panel RH (501-05 Interior Trim and Ornamentation, Removal and Installation).




Installation

3. Torque: 4 Nm
1. To install, reverse the removal position

2. Configure the electronic parking brake (EPB) using the diagnostic tool.

Parking Brake and Actuation - Parking Brake Switch
Removal and Installation

Removal

NOTES: Published: 12-Jun-2013

The parking brake switch is part of the transmission control switch (TCS) assembly and therefore can not be serviced
separately.


Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Transmission Control Switch (TCS) (307-05A Automatic Transmission/Transaxle External Controls - V6 3.0L Petrol, Removal and
Installation).

Installation


1. CAUTION: Make sure that all diagnostic trouble codes (DTCs) have
been removed after the road test.
To install, reverse the removal procedure.

Parking Brake and Actuation - Parking Brake Release Actuator
Removal and Installation

Removal Published: 06-May-2014

WARNING: Failure to release the tension and calibrate the electric parking brake during rear parking brake related service
procedures, could cause the parking brake to function incorrectly or become inoperative.

1. Refer to: Parking Brake Cable Tension Release (206-05 Parking Brake and Actuation, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Remove the differential case.

Refer to: Differential Case - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-02 Rear Drive Axle/Differential, Removal and Installation).
Refer to: Differential Case - TD4 2.2L Diesel/TDV6 3.0L Diesel (205-02,
Removal and Installation).

4. Torque: 7 Nm