2010 JAGUAR XFR brake

Published: 02-Oct-2012
Rear Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake
Caliper Vehicles With: High Performance Brakes
Removal and Installation

Removal


WARNING: Failure to release the tension and calibrate the electric parking brake during rear parking brake related service
procedures, could cause the parking brake to function incorrectly or become inoperative.


CAUTION: Brake fluid will damage paint finished surfaces. If spilled, immediately remove the fluid and clean the area
with water.


NOTE: Removal steps in this procedure may contain installation details.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

3. Refer to: Parking Brake Cable Tension Release (206-05 Parking Brake and Actuation, General Procedures).

4.

5. NOTE: Left-hand shown, right-hand similar.

Torque: 10 Nm





















6. CAUTIONS:


Always plug any open connections to prevent
contamination.


If brake fluid is spilt on the paintwork, the affected
area must be immediately washed down with cold water.
NOTES:


To prevent the loss of brake fluid, using the special
tool apply the brake pedal and set to 40mm ( 1.6 in ) below
the rest position.


Left-hand shown, right-hand similar.
Torque: 42 Nm

Installation
9.

























10.
WARNING: If the brake caliper piston seal is damaged
a new brake caliper must be installed.


CAUTION: Do not allow the brake caliper to hang on
the brake hose.


NOTE: Left-hand shown, right-hand similar.

Torque: 28 Nm














NOTE: Left-hand shown, right-hand similar.

1. To install, reverse the removal procedure.

2. Refer to: Brake System Bleeding (206-00 Brake System - General Information, General Procedures).

Published: 11-May-2011
Rear Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake
Disc Vehicles With: High Performance Brakes
Removal and Installation

Removal


CAUTION: Brake discs must be renewed in pairs.


NOTE: Removal steps in this procedure may contain installation details.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Brake Pads - Vehicles With: High Performance Brakes (206-04B Rear Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol,
Removal and Installation).

3.

4.
Installation



Torque: 103 Nm
























Remove the 2 clips.
Clean the components mating faces.
1.Toinstall,reversetheremovalprocedure.

Published: 11-May-2011
Rear Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake
Pads Vehicles With: High Performance Brakes
Removal and Installation

Special Tool(s)


206-080
Brake caliper piston retractor tool

206-081
Brake caliper piston retractor tool

303-588
Remover, Crankshaft Pulley/Damper Removal

WARNINGS:


Failure to release the tension and calibrate the electric parking brake during rear parking brake related service procedures,
could cause the parking brake to function incorrectly or become inoperative.


Do not allow dirt or foreign liquids to enter the reservoir. Use only new brake fluid of the correct specification from
airtight containers. Do not mix brands of brake fluid as they may not be compatible.


Brake pads must be renewed in axle sets only, otherwise braking efficiency may be impaired.


CAUTION: Brake fluid will damage paint finished surfaces. If spilled, immediately remove the fluid and clean the area
with water.
NOTES:


Only extraction bolt from special tool 303-588 is used.


Removal steps in this procedure may contain installation details.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

8. WARNING: If the brake caliper piston seal is damaged a
new brake caliper must be installed.


CAUTION: Do not allow the brake caliper to hang on
the brake hose.


NOTE: Left-hand shown, right-hand similar.

Torque: 28 Nm













9. NOTE: Left-hand shown, right-hand similar.

10.























11. NOTE: Left-hand shown, right-hand similar.

Special Tool(s): 303-588 Special Tool(s): 206-080 Special Tool(s): 206-081 Using the special tools, fully retract the brake
caliper piston.














12.
Repeat the above procedure on the opposite side.

Installation


1. NOTE: The brake pad wear sensor retaining tang must be
installed to the sensor prior to installation to the brake
pad.











2. To install, reverse the removal procedure.

3. Repeat the above procedure on the opposite side.

Published: 11-May-2011
Rear Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake
Disc Shield
Removal and Installation

Removal

WARNING: Make sure to support the vehicle with axle stands.

1. Raise and support the body.

2. Remove the brake disc.
For additional information, refer to: Brake Disc (206-04A Rear Disc Brake - V6 3.0L Petrol, Removal and Installation).

3. Remove the brake disc shield.
Drill out the 3 rivets












Installation

1. To install, reverse the removal procedure.