2010 AUDI A5 CABRIOLET technical data

______________________________________________________ P_a _ r_ k_ a_ s_s _i _ s _t __ _
Park assist
Applies to vehic les: wit h pa rk ing s yst e m
Parking system
D iff erent park assist systems may be used for parking or
maneuvering, depending on the vehicle's features .
Parking system (rear)*:
For the parking system, the acoustic par k assist system is installed in
the rear of the vehicle=>
page 163.
The rear par king assist sys tem uses ultrason ic sensors to determine
the distance of the vehicle from a detected obstacle. There are a total
o f f our sensors located on t he rear bumper (two in the middle and
two on the sides).
Parking system (rear, with rear-view camera)*:
For the parking system (rear , wi th rear-view camera), the rear
aco ustic park assist system is integ ra ted in the rear of the vehicle and
the rear-view camera is integrated in the rear lid=>
page 167.
The parking system (rear, with rear-view camera) uses ultrasonic
senso rs to determine the distance of the vehicle from a detected
obstacle. The re are a total of four sensors located on the rear bumper
(two in the m iddle and two on t he sides). •
Controls and equip ­
ment Safety first
Parking system (rear)
Ap
plies to vehicl es: w ith pa rk ing s yste m (r ear)
Rear acoustic park assist
The rear acous tic park assist warns you of obstacles or
objects behind your car .
Description
The rear a co ustic parki ng assis t sys tem de termines t he d istance o f
the vehicle from an obstacle us ing ultraso nic sensors . There are 4
sensors in the rear bumpe r.
T he range at which the sensors start to measure is
about :
To the side
Center rear
Acti vation
2 ft (0.60 m)
5.2 ft (1.60 m)
Aco ustic park ing assis t is activated au tomatically when
rever se gear
is engaged. A brief tone confirms that the system is activated .
Warning tones
Distance warning is given by chimes which are generated by the rear
signal generator . The vo lume and the pi tch of the chimes can be
adjusted in the radio or i n the MMI* =>
page 164 .
Reversing
Distance warn ing when reversing starts when an obstacle is detected
in the range o f th e parking ass ist system . As t he distance decre ases,
the time interva l between the a udible tones becomes shorter .
Whe n the distance is less than 1 ft (0.30 m), the tone becomes
c ont inuo us. A t this point you should stop ba cking up.
Vehicle care Technical data

______________________________________________________ P_a _ r_ k_ a_ s _ s_is _ t _ __.fflll
& WARNING
• You should a lways adju st the volum e and fr equency of the
c hime s so that you can ea sily hear the ac oustic di stance warning
even if the rad io is playing, the air-conditioner blowe r is on High
or there is a high level of outside noise.
- Check the setting s whenever anyone els e ha s dri ven the
vehicle before you. •
Parking system (rear, with rear­
view camera)
App lies to vehicl es: w ith par king system (rear) and rear -view camera
Introduction
Contro ls a nd e quip ­
m en t
0 ~ 9
" co m
Fig . 167 Parking
mode 1 : rever se
parking
Vehicle OP-eration
Fig. 168 Pa rkin g
mode 2: p ara llel
p ark in g
Vehicles with the park ing system are equ ipped with a rear-view
camera in additio n to the aco ust ic and visual pa rking system .
You ca n choose between two modes to ass ist yo u w ith pa rk ing . Fo r
example, you can use "parking model" when parking in a parking
sp ace or garage ~ fig . 167. When you wan t to p ark paralle l to the
edge of the street, select "park ing mode 2"
~ fig. 168.
& WARNING
• The rear-view camera has blind spots, in which objects cannot
be detected. Be especially careful to check for small children and
animals before backing up. Small ch ildren and animals will not
alway s be detected by the sen sors. •
Vehicle care Do-it-yourselt service iTechnical data

___________________________________________________ P_ a_r _k _ a_s _s_ i_s _t __ ffllll
• Remove snow with a hand brush and ice preferably with a de- ic ing
spray ~(D .
& WARNING
• The park ing aid cannot repla ce the dri ver' s attention . The
dri ver alone is res pon sible f or p arking and sim ilar dri ving m aneu­
ve rs.
• Always keep yo ur eyes on the vehicle 's su rro unding s, usi ng th e
r e ar -view mirror a s we ll.
• Do not all ow y ourself to be dist racted from tr affic b y th e re ar­
v iew cam era pic ture s.
• If the p osit ion and the in stall ati on ang le of the came ra has
c hange d, fo r ex ample, aft er a rea r end collisi on, do n ot contin ue
to u se the system for safe ty rea sons . Ha ve it ch ecked b y a qualifi ed
d eal ers hip.
0 Note
• Low obstacles a lready s ignaled by a warning can disappear from
the system's detection range as they are approached and will not
cont inue to be s ignaled. Objects such as bar rier chains, t railer draw
bars, thin painted vertical poles or fences may not be detected by the
system, pos ing ris k of damage .
• Never use warm or hot water to remove snow or ice from the rear­
view came ra lens -danger of crack format io n on the lens!
• When cleaning the lens, never use products that are abrasive.•
Controls and equip ­
ment Safety first
A
pp lies to vehicles : wi th par king syst em (r e a r) a nd r ear-v iew came ra
Sw itching on /off
The rearview camera switches on automatically together
with the acoustic and optical park assist when you put the
vehicle in reverse .
Activation
-Put the vehicle in reverse gear, the acoustic parking
system with rear-view camera is activated automatically .
Activation of the acoustic pa rking system is confirmed by
a brief acknowledgement sound .
Switching between the rearview camera and
optical display
-Press the Graphic control button~ page 168, fig. 171 ®
to see the optical display.
- Press the
Rear view control button to see the rearview
camera image.
Deactivat ion
- Take the vehicle out of reverse gear. The acoust ic parking
system is immediate ly deactivated, and the rear-v iew
camera picture is deactivated automatically after a period
of about 15 seconds, or
- Switch the ignition off, the entire acoustic parking system
is automatically deactiva ted.
T he rear-view camera will deactivate a utoma tica lly when you shift
into a forward gear and dr ive faster than about 9 mph (15 km/h) .
Th e de lay in deactivating the camera provides an uninterrupted view
behind the vehicle espec ia lly when maneuver ing in tight parking
spaces and prevents the picture from turning off the every time you
shift out of reverse. _..
Vehicle care Technical data

----------------------------------------------~P~a..!..r ~k :...:a:!.s~s!..:is~t ~_J-
& WARN ING (continued)
y ou sh oul d no t use th e help line s to help w ith pa rki ng, wh ic h
p os es dang er of an a ccident!
0 Note
• Low obstacles a lready s ignaled by a wa rning can disappear from
t he sys tem' s de tec tion range as they are approached and will no t
cont inue to be s ignaled. Objects such as bar rier chains, trailer draw
bars, thin pa inted vertical poles or fences may not be detected by the
system, posing risk of damage.
• In the MMI display, the direc tion of travel of the vehicle rear is
represented depend ing on the stee ring whee l angle. The vehicle front
swings out more than the vehicle rear . Maintain plenty of distance
from an obstacle so that your outs ide mirror or a corner of your
vehicle does not collide with any obstacles -danger of accident! •
Applies to veh icl es: wit h pa rk ing syst em (rear ) and re ar-v iew ca mer a
Parallel Parking
Use parking mode 2 to help you park on the edge of a
street.
Con tro ls a nd e quip ­
m en t
Fig.173 MMI Display :
b lu e s urface In th e
par king s lot
Vehicle OP-eration
Fig.174 MM I Dis pl ay:
Bl ue cur ve on t h cur b
The following steps apply only when there is no obstacl e
(such as a wall) near the parking spot. Otherw ise, please read
the "Tips o n Parking Next to Obstacles" .
- Activate the turn signal.
- Switch the MMI on and select the reverse gear. The
parking a id turns on and parking mode 1 appears on the
display.
- Position your vehicle parallel to the edge of the street,
approximately 1 meter from a parked vehicle.
- Press the
Mode ~ fig. 173 © control button on the MMI
control console . Parking mode 2 appears .
- Back up in reverse gear a nd alig n your veh icle so that the
blue area
0 borders on the rear end of the veh icle or on
the parking spot line . The blue area represents an exten­
sion of the vehicle's out line by approximately 5 m to the
rear. The long side of the b lue area should be on the curb .
The entire blue area must fit into the park ing spot.
- Whi le the vehicle is stationary, turn the steering whee l to
the right as far as it will go . _.,
Vehicle care Do-it-yourselt service iTechnical data

Park assist -
----------------
[I) Tips
• The warn ing tones can also be adjusted directly by the visual
display or the picture from the rearview camera. Simply press the
Settings control button.
• Changed settings are activated when parking system is switched
on again.
• Th e settings are automatically stored and assigned to the remote
control key .•
Ap plies to vehicl es: wit h pa rk ing System (re ar) and rea r-v iew ca mera
Acoustic parking system error message
If a warning tone is aud ible for about five seconds when you turn on
the ignition, there is a malfunction in the system. Have the problem
corrected by yo ur authorized Audi dealer .
Keep the sensors in the rear bumper clean and free from ice so that
the acoustic park assist system can function properly. •
Controls and equip­
ment Safety first
Vehicle care Technical data

HomeLink® -_______________ __.
Applies to veh icles : w ith Home link® un iversa l remote cont rol
Programming the Homelink ® transmitter
The transmitter is programmed in two phases . For rolling
code transmitters, a third phase is also necessary .
Fig. 175 Overhead
console: Homelink ®
k eypa d
Fig. 176 Radiator
grille
Phase 1: programming the overhead keypad
1. Make sure your vehicle is within operating range of the
remote controlled garage door opener .
2. Set the parking brake=>
& in "General information" on
page 172 .
3. Turn the ignition on . Do not start the engine!
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
4. Press and hold the two outside Homelink ® buttons G)and
@ for approximately 20 seconds until indicator light@
=> fig. 175 begins to flash . Then release both buttons. Do
not hold the buttons for longer than
30 seconds .
- This procedure only needs to be performed
once. It erases
the factory-set default codes and does not have to be
repeated to program additional remote controls.
5. Press and hold the Homelink ® button G), @ or@ until
the indicator light @starts flashing
slowly . Release the
button.
- The system will remain in programming mode for 5
minutes. Co to the front of the vehicle and proceed with
phase
2.
Phase 2: at the radiator grille
6. Point the original remote control to the m iddle of the
radiator grille of your vehicle=> fig.
176.
7. Hold the original remote control at a distance between O­
S in. (0-13 cm) (use the shortest distance possible) .
8 . Press and hold the activation button on the remote
control.
- May be different in Canada . If so, press and re-press
(cycle) the activation button on your remote control every
two seconds.
9. The emergency flashers will flash
three times (after about
15-60 seconds) when the programming is successful.
Release the button on the remote control.
- To program more devices , repeat steps 4 to 9.
Vehicle care Do-it-yourselt service iTechnical data

HomeLink® -
----------------
Applies to vehicles : w ith Home link® un iversa l remote cont rol
Reprogramming a single button
A HomeLink ® button con be reprogrammed individually
without affecting the other button allocations .
Programming the overhead keypad
Press the appropriate Homelink® button until the indi ­
cator light begins flashing slowly.
At the radiator grille
1. Point the original remote control to the middle of the
radiator grille of your vehicle~
page 173, fig. 176.
2. Hold the original r emote control at a distance between O­
S in . (0 -13 cm) (use the shortest distance poss ible) .
3 . Press and hold the activation button on the remote
control.
4. The emergency flashers will flash three times (after about
15-60 seconds) when the programming is successful.
Now release the button on the remote control.
- If the device utilizes a rolling code, please follow phase 3
of ~
page 173 , "Programming the Homelink® trans­
mitter" for rolling code programming.
This procedure will cause the existing programming on the
Homelink ® button to be erased! •
Controls and equip ­
ment Safety first
App
lies to vehicles : w ith Home link® un iversa l remote cont rol
Erasing the programming of the
Homelink ® transmitter
When you erase the programming, the programming on
all three of the transmitter channels with be lost!
- Perform steps 1 to 4 as described on ::::;, page 173, "Phase
1: programming the overhead keypad" .
When completed, the Homelink® system will be in the programming
mode and is then ready to learn the codes for remote controlled
devices.
[I] Tips
• Programm ed buttons canno t be e ras ed ind iv idually.
• For security reasons you are adv ised to erase the programming of
the Horne Link ® system befo re you sell your vehicle. •
Vehicle care Technical data

Driving Safely ---------------------"~'----
Important things to do before driving
Safety is everybody's job! Vehicle and occupant safety
always depends on the informed and careful driver.
For your safety and the safety of your passengers, before
driving always:
- Make sure that all lights and signals are operating
correctly.
- Make sure that the tire pressure is correct.
- Make sure that all windows are clean and afford good visi-
bility to the outside.
- Secure all luggage and other items carefully::::>
page 86.
-Make sure that nothing can interfere with the pedals.
- Adjust front seat, head restraint and mirrors correctly for your height .
- Instruct passengers to adjust the head restraints according to their height.
- Make sure to use the right child restraint correctly to
protect children ::::,
page 222, "Child Safety".
- Sit properly in your seat and make sure that your passen­ gers do the same::::,
page 77, "General recommenda­
tions".
- Fasten your safety belt and wear it properly. Also instruct
your passengers to fasten their safety belts properly
=:> page 190. •
Controls and equip­
ment Safety first Vehicle operation
What impairs driving safety?
Safe driving is directly related to the condition of the
vehicle, the driver as well as the driver's ability to concen­
trate on the road without being distracted .
The driver is responsible for the safety of the vehicle and all
of its occupants. If your ability to drive is impaired, safety
risks for everybody in the vehicle increase and you also
become a hazard to everyone else on the road::::,,& . There­
fore:
Do not let yourself be distracted by passengers or by using
a cellular telephone.
NEVER drive when your driving ability is impaired (by
medications, alcohol, drugs, etc.).
- Observe all traffic laws, rules of the road and speed limits
and plain common sense .
- ALWAYS adjust your speed to road, traffic and weather
conditions.
- Take frequent breaks on long trips. Do not drive for more than two hours at a stretch.
- Do NOT drive when you are tired, under pressure or when
you are stressed .
& WARNING
Impaired driving safety increases the risk of serious personal
injury and death whenever a vehicle is being used.•
Vehicle care Do-it-yourself service Technical data