2010.5 Peugeot 206 P Dag Owner's Manual

INSTRUMENTS and CONTROLS
20

Warning lamp is on Cause Action/Observations

Engine
autodiagnosis system fi xed. The emission control system
has a fault.
This lamp should go off when the engine is started
.
If it does not go off, contact a PEUGEOT dealer
urgently.
Particle emissions fi lter fault
(fuel additive level, risk of
blockage...). Refer to the "Checks" section.
Have it checked by a PEUGEOT dealer.
fl ashing. The engine management
system has a fault. Risk of destruction of the catalytic converter.
Have it checked by a PEUGEOT dealer.

Low fuel level fi xed with the
needle in the red zone. When it fi rst comes on there
remains approximately
5 litres
of fuel in the tank.
At this point, you begin to use
the fuel reserve. Refuel as soon as possible to avoid running
out of fuel.
This warning lamp will come on every time
the ignition is switched on, until a suffi cient
addition of fuel is made.
Fuel tank capacity: approximately
50 litres .
Never continue to drive until you run out
of fuel, as this could damage the emission
control and injection systems.

Maximum
coolant
temperature fi xed with
the needle in
the red zone. The temperature of the cooling
system is too high. Stop as soon as it is safe to do so.
Wait until the engine has cooled down before
topping up the level, if necessary.
If the problem persists, contact a PEUGEOT
dealer.

Engine oil
pressure fi xed. There is a fault with the engine
lubrication system. Stop as soon it is safe to do so.
Park, switch off the ignition and contact a
PEUGEOT dealer.

INSTRUMENTS and CONTROLS
21

Warning lamp is on Cause Action/Observations

Battery
charge fi xed. The battery charging circuit has
a fault (dirty or loose terminals,
slack or cut alternator belt, ...). The warning lamp should go off when the
engine is started.
If it does not switch off, contact a PEUGEOT
dealer.

Seat belt not
fastened/
unfastened fi xed.
The driver has not fastened or
has unfastened their seat belt. Pull the strap then insert the tongue in the
buckle.

Airbags temporarily.
This lamp comes on for a few
seconds when you turn on the
ignition, then switches off.
This lamp should switch off when the engine is
started.
If it does not switch off, contact a PEUGEOT deale
r.
fi xed. One of the airbag or seat belt
pretensioner systems has a
fault. Have it checked by a PEUGEOT dealer.

ii
INSTRUMENTS and CONTROLS
22
COOLANT TEMPERATURE
INDICATOR
System which informs the driver of
the changes in the temperature of the
engine coolant while driving.
With the engine running, when the nee-
dle is:
- in zone A , the temperature is correct,
- in zone B , the temperature is too
high; the max temperature warning
lamp 1 and the central STOP warn-
ing lamp come on, accompanied by
an audible signal and a message in
the multifunction screen.

You MUST stop as soon as it is safe
to do so.
Consult a PEUGEOT dealer. After driving for a few minutes, the tem-
perature and pressure in the cooling
system increase.
To top up the level:

 wait for the engine to cool,

 unscrew the cap by two turns to
allow the pressure to drop,

 when the pressure has dropped,
remove the cap,

 top up the level to the "MAX" mark
(circular line).
On petrol engines, the cooling of the
engine is managed electronically
to reduce fuel consumption. Con-
sequently, the coolant temperature
levels are no longer simply linked
with the external ambient condi-
tions and the use of the vehicle.
For example, in town, it is normal for
the coolant temperature to be slight-
ly higher in cold weather than in hot
weather (normal operation may lead
to a temperature of over 100 °).

INSTRUMENTS and CONTROLS
23
SERVICE INDICATOR
System which informs the driver when the
next service is due, in accordance with
the manufacturer's servicing schedule.
The point at which the service is due is
calculated from the last indicator zero
reset. It is determined by two param-
eters:
- the distance travelled,
- the time elapsed since the last ser-vice. More than 1 000 km remain before
the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.

Example: 4 800 km remain before the
next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the spanner
goes
off ; the distance
recorder resumes its normal operation.
The display then indicates the total and
trip distances. Less than 1 000 km remain before
the next service is due

Example: 900 km remain before the
next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains on to indicate that a service
must be carried out soon.

ii
ii
INSTRUMENTS and CONTROLS
24
Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at least
fi ve minutes for the zero reset to be
taken into account.
Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:

 switch off the ignition,

 press and hold the trip distance re-
corder zero reset button,

 switch on the ignition; the distance
recorder display begins a count-
down,

 when the display indicates "=0" ,
release the button; the spanner
disappears.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes to
indicate that the service must be carried
out as soon as possible.

Example: the service is overdue by
300 km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains
on .

INSTRUMENTS and CONTROLS
25
TOTAL DISTANCE RECORDER
System which measures the total dis-
tance travelled by the vehicle during its
life. LIGHTING DIMMER
System for manual adjustment of the
brightness of the instrument panel in
relation to the exterior brightness.
The total and trip distances are dis-
played for thirty seconds when the ig-
nition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
TRIP DISTANCE RECORDER
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

 With the ignition on, press the but-
ton until zeros appear. Activation
When the exterior lighting is on:

 press the button to change the
brightness of the instrument panel,

 when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or

 when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,

 when the lighting reaches the level
of brightness required, release the
button.
Deactivation
When the exterior lighting off, pressing
the button does not have any effect.

INSTRUMENTS and CONTROLS
26
MONOCHROME SCREEN A Adjusting the parameters
Press and hold button 1 for two seconds
to access the settings; the data fl ashes,
indicating it is ready to be modifi ed.
Then, each press of button 1 scrolls
through the various data in the following
order:
- language of information displayed,
- hours (12 then 24 hour mode),
- minutes,
- year,
- month,
- day,
- unit of temperature (degrees Cel- sius or Fahrenheit).
Pressing button 2 allows modifi cation
of the data selected. Press and hold for
rapid advance (return to start after the
last possible value).
After 7 seconds with no action, the main
display returns; the modifi ed data are
now recorded.

Note: Pressing button 2 briefl y displays
the ambient temperature for a few
seconds.
When the ambient temperature is be-
tween -3° and 3 °C, the ambient tem-
perature display on the screen takes
priority over the clock display.
This displays the following information:
- time,
- date,
- ambient temperature * (this fl ashes
when it is between -3 and 3 °C),
- audio system information,
- a door check (e.g.: ''left front door open''),
- warning messages (e.g. ''remote control battery fl at'') or information
messages (e.g. ''economy mode
active''), displayed temporarily.
* With digital air conditioning only.

INSTRUMENTS and CONTROLS
27
MONOCHROME SCREEN B
This enables the following information
to be displayed:
- time,
- date,
- ambient temperature * (this fl ashes when it is between -3 and 3 °C),
- status of the doors. The display shows you, by means of a graphic,
whether a door is open,
- warning messages (e.g. ''battery charge fault'') or information mes-
sages (e.g. "fuel level low''), dis-
played temporarily, can be cleared
by pressing button 1 or 2 ,
- trip computer. Setting the parameters
Press button
1 for two seconds to access
the settings. The information fl ashes to
show it is ready to be modifi ed.
Then, individual presses on button 1
allow you to scroll through the various
data in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (degrees Cel- sius or Fahrenheit),
- time format (12 then 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button 2 allows you to change
the information selected. Maintain the
pressure for rapid scrolling.
After 7 seconds without operation, the
screen returns to the normal display
and the modifi ed data is recorded.

Note: Pressing button 2 briefl y displays the
outside temperature for a few seconds.
When the ambient temperature is be-
tween -3° and 3 °C, the temperature
display takes priority over the time on
the screen.
* With digital air conditioning only.