2010.5 Peugeot 206 P Dag Owner's Manual

84
SPECIAL FEATURES OF ALLOY WHEELS
Fitting the spare wheel
If your vehicle is equipped with a steel
spare wheel, when fi tting it, it is nor-
mal to notice that the bolt washers do
not come into contact with the rim. The
spare wheel is secured by the conical
section of each bolt. Fitting snow tyres
If you fi t snow tyres that are mounted on
steel rims on your vehicle, it is
essen-
tial that you use special bolts available
from PEUGEOT dealers.

i
85
CHANGING A BULB
Front lamps

1. Direction indicators
(PY21W amber).

2. Sidelamps (W5W).

3. Dipped beam headlamps
(H7-55W).

4. Main beam headlamps (H1-55W).

5. Foglamps (PSX-24W).
Operating procedure for replacing a
faulty bulb with a new bulb. These op-
erations must be carried out
with the
ignition off .
To gain access to the bulbs on the right-
hand side * :
- Remove the screenwash reservoir fi ller tube.
- Unclip the engine harness 1 .
- Remove the nut from the engine management unit support 2 using a
size 10 spanner.
- Remove the engine management unit and support assembly. After changing the faulty bulb:
- Slide the two lugs of the engine
management unit support into the
locations A .
- Put the engine management unit back in place.
- Tighten the engine management unit support nut (size 10 spanner).
- Reclip the engine harness.
These bulbs are available from
PEUGEOT dealers.
In certain climatic conditions (low
temperature, humidity), conden-
sation inside the glass of the
headlamps and other lamps is
normal .
However, contact a PEUGEOT
dealer if water is present in the
headlamps.
* Petrol engines only.

i
86

 Turn the bulb holder a quarter turn
and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specifi cation and colour.
Direction indicators

 Disconnect the headlamp main
connector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Pull the bulb out and change it. Dipped beam headlamps

 Disconnect the headlamp main con-
nector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Press the connector downwards to
release the bulb.

 Pull the bulb out and change it.
To refi t, carry out these operations in
reverse order.
Sidelamps

!
87
Front foglamp

 Slide a hand under the bumper.

 Turn the connector a quarter turn
and remove the assembly.

 Remove the bulb and change it.
Main beam headlamps

 Disconnect the headlamp main
connector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Move aside the springs to release
the bulb and pull the bulb out.
To refi t, carry out these operations in
reverse order. Direction indicator side repeater

 Push the repeater forwards and
release it.

 Remove the repeater and change it.
Repeaters can be obtained from a
PEUGEOT dealer.

High pressure washing
When using a jet washer on stub-
born dirt, do not persist on the
headlamps, the other lamps and
their surround to avoid damaging
their coating and seals.

88
Third brake lamp 5 bulbs W5W
Unclip the boot side trim.
Remove the wing nut.
Release the lamp unit from the outside.
Press the lug A and disconnect the
connector.
Remove the sealing foam.
Move aside the tabs B and remove the
bulb holder.
Turn the faulty bulb a quarter turn and
change it.
To refi t, carry out these operations in
reverse order and ensure that the bulb
holder, the lamp unit and the foam cover
are repositioned correctly. Using a 10 mm spanner, unscrew the
2 nuts
A .
Release the lamp unit.
Squeeze the two tabs B to release the
bulb holder.
Change the faulty bulb.

1. Direction indicators
(P21W amber).

2. Reversing lamps P21W.

3. Brake lamps/sidelamps (P21/5W).

4. Foglamp (P21W).
Rear lam
ps

89
Rear foglamp (P21W)
The foglamp is located on the rear
bumper, on the left-hand side.
Unscrew the lamp and release the
assembly.
Turn the pin connector a quarter turn
and remove it.
Change the bulb. Number plate lamps W5W
Insert a thin screwdriver into one of the
outer holes of the transparent cover.
Push it outwards to unclip it.
Remove the transparent cover.
Change the faulty bulb.

90
CHANGING A FUSE
Operating procedure for replacing a
faulty fuse with a new fuse to rectify a
failure of the corresponding function.
The fuseboxes are located under the dash-
board and in the engine compartment.
Dashboard fusebox
Unscrew the catch a quarter turn using
a coin then remove the cover to gain
access to the fuses and the tweezer A . Removing and fi tting a fuse
Before changing a fuse, the cause of the fault must be fou
nd and rectifi ed. The
fuse numbers are indicated on the fusebox.
Use the tweezer A .

Always replace a faulty fuse with a fuse of the same rating .
Tweezer A

Good Failed

90
CHANGING A FUSE
Operating procedure for replacing a
faulty fuse with a new fuse to rectify a
failure of the corresponding function.
The fuseboxes are located under the dash-
board and in the engine compartment.
Dashboard fusebox
Unscrew the catch a quarter turn using
a coin then remove the cover to gain
access to the fuses and the tweezer A . Removing and fi tting a fuse
Before changing a fuse, the cause of the fault must be fou
nd and rectifi ed. The
fuse numbers are indicated on the fusebox.
Use the tweezer A .

Always replace a faulty fuse with a fuse of the same rating .
Tweezer A

Good Failed