2009 SUBARU TRIBECA window

GW-22
Rear Gate Glass
GLASS/WINDOWS/MIRRORS
15.Rear Gate Glass
A: REMOVAL
1) Remove the rear wiper motor. REMOVAL, Rear Wiper Motor.>
2) Disconnect the electrical connectors from rear
defogger terminal.
3) Remove the glass in the same procedure as for
windshield glass. Windshield Glass.>
B: INSTALLATION
1) Mount the fastener on the body.
2) Install the dam rubber.
3) Cut off the cartridge nozzle tip as shown and set
it in sealant gun.
4) Apply adhesive in the same procedure as for
windshield glass. TION, Windshield Glass.>
5) Insert the glass clip pin into rear gate hole, push
on the area around the clip pin to secure it, and
then push lightly all around the area to seal it.
(1) Glass
(2) Spacer
(3) Adhesive
(4) Fastener
(5) 4 mm (0.15 in)
(6) 8 mm (0.31 in)
(7) 10 mm (0.39 in)
(8) 5.5 mm (0.22 in)

GW-23
Rear Gate Glass
GLASS/WINDOWS/MIRRORS
6) About one hour after installation, conduct a leak test.
7) After completion of all work, allow the vehicle to
stand for about 24 hours.
NOTE:
•When door is opened/closed after glass is bond-
ed, always lower the door glass first, and then
open/close it carefully.
•Move the vehicle slowly.
•For minimum drying time and vehicle standing
time before driving after bonding, follow instruc-
tions or instruction manual from the adhesive man-
ufacturer.
•When a vehicle is returned to the user, tell him or
her that the vehicle should not be subjected to
heavy impact for at least three days.
8) Connect the rear defogger terminals.
9) Install the rear wiper. LATION, Rear Wiper Motor.>
(1) Glass (4) Adhesive (6) Spacer
(2) Glass clip pin (5) Dam rubber (7) Marks for applying the primer
(3) Fastener

GW-24
Rear Window Defogger System
GLASS/WINDOWS/MIRRORS
16.Rear Window Defogger System
A: WIRING DIAGRAM

B: INSPECTION
NOTE:
Rear window defogger system can be customized on the Subaru Select Monitor.
Symptom Repair order
Rear window defogger does not operate.
1. Fuse (M/B No. 10) (F/B No. 22)
2. Rear defogger relay
3. Defogger switch
4. Rear defogger condenser
5. Defogger wire
6. Wiring harness
7. Body integrated unit
System name Initial setting Customize setting
Rear window defogger timer OFF after 15 min.Repeat 15 min. operation and
2 min. stop.

GW-25
Rear Window Defogger
GLASS/WINDOWS/MIRRORS
17.Rear Window Defogger
A: INSPECTION
1. CHECK WITH SUBARU SELECT MONITOR
CAUTION:
Check that the rear window defogger timer is in initial setting or customize setting before performing
inspection.
2. HEAT WIRE INSPECTION
CAUTION:
Use a dry and soft cloth when wiping dirt off the
glass. Move the cloth along the heat wire to
avoid damaging it.
1) Turn the ignition switch to ON.
2) Turn the defogger switch to ON.
3) Wrap the tips of tester probe with aluminum foil
to avoid damage to heat wire.
4) Measure the voltage at heat wire center with DC
voltmeter.
Standard voltage:
Approx. 6 V
NOTE:
•If the measured value is 12 volts, heat wire is
open between heat wire center and positive (+) ter-
minal of tester probe.
•If it is 0 V, the circuit is open between heat wire
center and ground.
Step Check Yes No
1CHECK INPUT SIGNAL TO THE BODY INTE-
GRATED UNIT.
Check the input signal when the rear window
defogger switch is operated using Subaru
Select Monitor.
1) Connect the Subaru Select Monitor to data
link connector.
2) Turn the ignition switch to ON.
3) Select {Integ. unit} from the «main menu».
4) Select the {Current Data Display & Save}.
5) Check the input signal when the rear win-
dow defogger switch is set to ON.
After rear defogger switch is
set to ON, does it turn to OFF
in 15 minutes? Or does it
repeat 15 minutes operation
and 2 minutes stop?
END. Replace the body
integrated unit.
REMOVAL, Body
Integrated Unit.>
(1) Tester probe
(2) Aluminum foil
(3) Heat wire
(4) Press
GW-00076
(2)
(3)
(4)
(1)
(1) Center of heat wire
Vo l t a g e C r i t e r i a
Approx. 6 V Normal
Approx. 12 V or 0 V Open
GW-00077
(1)

GW-26
Rear Window Defogger
GLASS/WINDOWS/MIRRORS
5) Connect the tester probe of positive lead of volt-
meter to positive terminal of heat wire and move
tester probe of negative lead along the heat wire up
to the negative terminal end. If voltage changes
from zero to several volts during movement of
tester probe, heat wire is open at the voltage
change point.
B: REPAIR
1) Clean the broken portion with alcohol or white
gasoline.
2) Mask both side of wire with thin film.
3) Apply the conductive silver composition (DU-
PONT No. 4817) to the broken portion.
4) After repair, check the wire.
(1) Broken portion
(2) Thin film
(3) Broken wire
(4) Conductive silver composition (DUPONT No.
4817)
GW-00078
(2)
(3)
(4)
(1)

GW-27
Rear Quarter Glass
GLASS/WINDOWS/MIRRORS
18.Rear Quarter Glass
A: REMOVAL
Remove the glass in the same procedure as for
windshield glass. Windshield Glass.>
B: INSTALLATION
1) Install the dam rubber.
2) Cut out the nozzle head and apply adhesive to
the glass end surface as shown.
3) Install the glass in the same procedure as for
windshield glass. TION, Windshield Glass.>
4) After completion of all work, allow the vehicle to
stand for about 24 hours.
NOTE:
•When door is opened/closed after glass is bond-
ed, always lower the door glass first, and then
open/close it carefully.
•Move the vehicle slowly.
•For minimum drying time and vehicle standing
time before driving after bonding, follow instruc-
tions or instruction manual from the adhesive man-
ufacturer.
5)After curing of adhesive, pour the water on external
surface of vehicle to check that there are no water leaks.
NOTE:
When a vehicle is returned to the user, tell him or
her that the vehicle should not be subjected to
heavy impact for at least three days.
(1) Locating pin
(2) Dam rubber
(3) Fastener
(4) Adhesive
(5) Encap molding
GW-00500
(4)
(2)
(5)
(2)
(1)(1)
(3)
C
B
BB
C
A
A
(1) Dam rubber
(2) Adhesive
(3) Encap molding
(4) 8 mm (0.31 in)
(5) 9 mm (0.35 in)
(6) 2 mm (0.07 in)
(7) 4 mm (0.15 in)
(8) 11 mm (0.43 in)
(9) 10 mm (0.39 in)
GW-00501
(3)
(4)(7)
(5)
(6)
(4)
(5)(6)
(7)
(2)
(1)
(3)
(2)
(8)
(4)
(6)
(5)
(3)
(2)
A-A
C-CB-B
(9)(4)
(6)
(5)
60

GW-28
Sun Roof Glass
GLASS/WINDOWS/MIRRORS
19.Sun Roof Glass
A: REMOVAL

B: INSTALLATION

C: ADJUSTMENT

GW-29
Rearview Mirror
GLASS/WINDOWS/MIRRORS
20.Rearview Mirror
A: REMOVAL
1) Remove the TORX® screw (1).
2) Slide the rearview mirror (2) to the upper side (A)
of windshield glass (3), and remove the mirror from
mount (4).
CAUTION:
•Be careful not to damage the mirror surface.
•Be careful not to damage the windshield
glass.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. General Description.>
CAUTION:
When tightening the mounting TORX® screw,
be sure to observe the tightening torque. Other-
wise, the mount may be damaged in over-
torque conditions.
C: INSPECTION
Check that the mirror is not damaged.
GW-00413(2)(1)
(3)
(4)(A)