2009 SUBARU TRIBECA light

LI-14
Front Turn Signal Light Bulb
LIGHTING SYSTEM
12.Front Turn Signal Light Bulb
A: REMOVAL
1) Open the front hood.
2) Turn the socket (A) and remove the front turn
signal light bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification.
tion.>
3) If NG, replace the bulb with a new one.

LI-15
Parking Light Bulb
LIGHTING SYSTEM
13.Parking Light Bulb
A: SPECIFICATION
The parking light bulb is integrated into the front
turn signal light bulb as a unit; therefore, refer to
“Front Turn Signal Light Bulb” for the removal pro-
cedure. nal Light Bulb.>

LI-16
Front Side Marker Light Bulb
LIGHTING SYSTEM
14.Front Side Marker Light Bulb
A: REMOVAL
1) Open the front hood.
2) Turn the socket (A) and remove the front turn
signal light bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification.
tion.>
3) If NG, replace the bulb with a new one.
LI-00508
(A)

LI-17
Front Fog Light Assembly
LIGHTING SYSTEM
15.Front Fog Light Assembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Disengage the three clips, and then turn over the
lower mud guard.
3) Disconnect the harness connector.
4) Remove the two mounting bolts, and then de-
tach the fog light assembly by pulling it.
B: INSTALLATION
Install in the reverse order of removal.
LI-00509

LI-18
Front Fog Light Bulb
LIGHTING SYSTEM
16.Front Fog Light Bulb
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Disengage the three clips, and then turn over the
lower mud guard.
3) Disconnect the harness connector.
4) Remove the back cover.
5) Remove the spring retainer (A), then detach the
fog light bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00510
LI-00511
(A)

LI-19
Side Turn Signal Light Assembly
LIGHTING SYSTEM
17.Side Turn Signal Light As-
sembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the mirror. MENT, Outer Mirror.>
3) Remove the scalp cap. PLACEMENT, Scalp Cap.>
4) Disconnect the harness connector, remove the 3
mounting screws and then remove the side turn
signal light assembly.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Install the side turn signal light assembly and
check that it blinks normally.
2) If it does not blink normally, replace the side turn
signal light assembly with a new one.
NOTE:
Because a LED (Light Emitting Diode) is used for
the side turn signal light, replace the side turn sig-
nal light as an assembly if the LED does not turn
on.
LI-00293

LI-20
Rear Combination Light Assembly
LIGHTING SYSTEM
18.Rear Combination Light As-
sembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the cover.
3) Remove the two bolts, and then detach the rear
combination light by pulling it to the rear side of ve-
hicle.
4) After turning the sockets of the tail/stop light
bulbs and rear turn signal light bulbs, remove the
rear combination light.
B: INSTALLATION
Install in the reverse order of removal.
LI-00512
LI-00513

LI-21
Tail/Stop Light Bulb
LIGHTING SYSTEM
19.Tail/Stop Light Bulb
A: REMOVAL
1. COMBINATION LIGHT
1) Remove the rear combination light assembly.
Assembly.>
2) Turn the socket and remove the bulb.
2. FINISHER LIGHT
1) Remove the bulb inspection cover of the rear
gate trim.
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00514
LI-00518