2009 SUBARU TRIBECA light

LI-22
Rear Turn Signal Light Bulb
LIGHTING SYSTEM
20.Rear Turn Signal Light Bulb
A: REMOVAL
1) Remove the rear combination light assembly.
Assembly.>
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00515

LI-23
Rear Side Marker Light Bulb
LIGHTING SYSTEM
21.Rear Side Marker Light Bulb
A: SPECIFICATION
The rear side marker light bulb is integrated into the
tail/stop light as a single unit; therefore, refer to the
section on tail/stop light bulbs for the removal pro-
cedures. Bulb.>

LI-24
Rear Finisher Light Assembly
LIGHTING SYSTEM
22.Rear Finisher Light Assembly
A: REMOVAL
1) Remove the bulb inspection cover of the rear
gate trim.
2) Disconnect the harness connector.
3) Remove the mounting nuts and detach the rear
finisher assembly.
B: INSTALLATION
Install in the reverse order of removal.
LI-00516
(A)
LI-00517

LI-25
Back-up Light Bulb
LIGHTING SYSTEM
23.Back-up Light Bulb
A: REMOVAL
1) Remove the bulb inspection cover of the rear
gate trim.
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.

LI-26
License Plate Light Assembly
LIGHTING SYSTEM
24.License Plate Light Assembly
A: REMOVAL
1) Remove the rear gate garnish. REMOVAL, Rear Gate Garnish.>
2) Disengage the clips, and disconnect the connec-
tors, and then detach the license lamp assembly.
B: INSTALLATION
Install in the reverse order of removal.
LI-00519

LI-27
License Plate Light
LIGHTING SYSTEM
25.License Plate Light
A: REMOVAL
1) Remove the license plate light mounting screw
(A) and then remove the lens (B).
2) Remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00520
(A)
(B)(B)
(A)

LI-28
High-mounted Stop Light
LIGHTING SYSTEM
26.High-mounted Stop Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Detach the roof spoiler. AL, Roof Spoiler.>
3) Remove the nuts (A), then detach the high-
mounted stop light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Install the high-mounted stop light to test if it illu-
minates normally.
2) If the high-mounted stop light does not illumi-
nate, replace it with a new one.
NOTE:
Since LEDs (Light Emitting Diodes) are used for
the high-mounted stop light, replace the high-
mounted stop light assembly when the LEDs went
out.
LI-00312
(A)(A)

LI-29
Spot Map Light
LIGHTING SYSTEM
27.Spot Map Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the lens.
3) Remove the four bolts used for mounting the
spot map light.
4) Disconnect the harness connectors and remove
the spot map light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. SPOT MAP LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. SPOT MAP LIGHT SWITCH
Measure the resistance between spot map light
switch terminals.
Switch position Terminal No. Standard
OFF — 1 MΩ or more
ON 1 and 2 18±5.4 Ω
LI-00521
LI-00522