2009 SUBARU TRIBECA ac 25 procedure

IM (diag)-19
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
IMMOBILIZER (DIAGNOSTICS)
C: DTC P1571 REFERENCE CODE INCOMPATIBILITY
DTC DETECTING CONDITION:
Reference code incompatibility between body integrated unit and ECM
7CHECK IGNITION KEY (TRANSPONDER).
1) Remove the key from ignition switch.
2) Start the engine using other key which is
already registered.
Does the engine start? Replace all the
ignition keys
(including tran-
sponder). Execute
the registration
procedure next.
Refer to the “REG-
ISTRATION MAN-
UAL FO R
IMMOBILIZER”.
Replace the body
integrated unit
Body Integrated
Unit.> and replace
all the ignition keys
(including tran-
sponder). Execute
the registration
procedure next.
Refer to the “REG-
ISTRATION MAN-
UAL FOR
IMMOBILIZER”.
Step Check Yes No
Step Check Yes No
1PERFORM TEACHING OPERATION OF IG-
NITION KEY.
Perfor m teaching operation on all keys of the
vehicle. Refer to the “REGISTRATION MAN-
UAL FOR IMMO BILIZER”.
Is the teaching operation for all
keys completed?
END. Go to step 2.
2CHECK ANY OTHER DTC ON DISPLAY.Is any other immobilizer DTC
displayed?
Check the appro-
priate DTC using
the “List of Diag-
nostic Trouble
Code (DTC)”.
14, List of Diag-
nostic Trouble
Code (DTC).>
Execute the regis-
tration procedure
next. Refer to the
“REGISTRATION
MANUAL FOR
IMMOBILIZER”.
Replace the ECM.
FU(H6DO)-32,
Engine Control
Module
(ECM).>Replace
the body inte-
grated unit to SL-52, Body
Integrated Unit.>
and replace all the
ignition keys
(including tran-
sponder). Execute
the registration
procedure next.
Refer to the “REG-
ISTRATION MAN-
UAL FOR
IMMOBILIZER”.

IM (diag)-20
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
IMMOBILIZER (DIAGNOSTICS)
D: DTC P1572 IMM CIRCUIT FAILURE (EXCEPT ANTENNA CIRCUIT)
DTC DETECTING CONDITION:
Communication failure between body integrated unit and ECM
WIRING DIAGRAM:
MAIN SBF
SBF-8
SBF-3BATTERYF/B NO.12
IGNITIONSWITCH
A1B28B18C9C2B7C8
E
F/B NO.7
M/B NO.8
BODY INTEGRATED UNIT
i84A:
B280B:
B281C:
B22
567821943102422 23 25111213141526 27281617181920 21
B281i84
1234567891011121314151617181920212223242526272829303132333435
5467821931022 231112131415242526 2716171828 29192021 30
B280A:C:B:B136C:
C26C34
B136C:ECM
IM-00142
16101112131415252430
9871718192028212223293231
123456
2726333435
Step Check Yes No
1CHECK BODY INTEGRATED UNIT POWER
SUPPLY CIRCUIT.
1) Turn the ignition switch to OFF.
2) Disconnect the harness connector from
body integrated unit.
3) Measure the voltage between body inte-
grated unit harness connector terminal and
chassis ground.
Connector & terminal
(B280) No. 7 (+) — Chassis ground (–):
(B281) No. 2 (+) — Chassis ground (–):
Is the voltage more than 10 V? Go to step 2.Check the harness
for open or shor t
circuit between
body integrated
unit and fuse.
2CHECK BODY INTEGRATED UNIT POWER
SUPPLY CIRCUIT.
1) Turn the ignition switch to ON.(Engine OFF)
2) Measure the voltage between body inte-
grated unit harness connector terminal and
chassis ground.
Connector & terminal
(i84) No. 1 (+) — Chassis ground (–):
Is the voltage more than 10 V? Go to step 3.Check the harness
for open or shor t
circuit between
body integrated
unit and ignition
switch.

IM (diag)-21
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
IMMOBILIZER (DIAGNOSTICS)
3CHECK BODY INTEGRATED UNIT GROUND
CIRCUIT.
1) Turn the ignition switch to OFF.
2) Measure the resistance between body inte-
grated unit harness connector terminal and
chassis ground.
Connector & terminal
(B280) No. 22 — Chassis ground:
(B281) No. 8, No. 9 — Chassis ground:
Is the resistance less than 10
Ω?
Go to step 4.Repair the open
circuit of body inte-
grated unit ground
circuit.
4CHECK HARNESS BETWEEN BODY INTE-
GRATED UNIT AND ECM.
1) Disconnect the harness connector from
body integrated unit and ECM.
2) Measure the resistance between body inte-
grated unit harness connector terminal and
ECM harness connector terminal.
Connector & terminal
(B280) No. 18 — (B136) No. 26:
Is the resistance less than 10
Ω?
Go to step 5.Repair the open
circuit of harness
between body inte-
grated unit and
ECM.
5CHECK HARNESS BETWEEN BODY INTE-
GRATED UNIT AND ECM.
Measure the resistance between body inte-
grated unit harness connector terminal and
ECM harness connector terminal.
Connector & terminal
(B280) No. 28 — (B136) No. 34:
Is the resistance less than 10
Ω?
Go to step 6.Repair the open
circuit of harness
between body inte-
grated unit and
ECM.
6CHECK HARNESS OF COMMUNICATION
LINE.
1) Turn the ignition switch to ON.(Engine OFF)
2) Measure the voltage between body inte-
grated unit harness connector terminal and
chassis ground.
Connector & terminal
(B280) No. 18, No. 28 (+) — Chassis
ground (–):
Is the voltage 0 V? Go to step 7.Repair the har-
ness between
body integrated
unit and ECM,
because there is
short circuit with
battery voltage line
or ignition switch
“ON” line.
7CHECK HARNESS OF COMMUNICATION
LINE.
Measure the voltage between harness connec-
tor terminal and engine ground.
Connector & terminal
(B136) No. 26, No. 34 (+) — Engine
ground (–):
Is the voltage 0 V? Go to step 8.Repair the har-
ness between
body integrated
unit and ECM,
because there is
short circuit with
battery voltage line
or ignition switch
“ON” line.
8CHECK ECM BY COMMUNICATION LINE
CHECK.
1) Connect the harness connector to ECM.
2) Disconnect the harness connector from
body integrated unit.
3) Start the communication line check. to IM (diag)-7, COMMUNICATION LINE
CHECK, OPERATION, Subaru Select Moni-
tor.>
Does “Communication Line not
Shorted” appear on the
screen?
Replace the body
integrated unit
Body Integrated
Unit.> and replace
all the ignition keys
(including tran-
sponder). Execute
the registration
procedure next.
Refer to the “REG-
ISTRATION MAN-
UAL FO R
IMMOBILIZER”.
Replace the ECM.
FU(H6DO)-32,
Engine Control
Module (ECM).>
Per fo r m th e re g is -
tration procedure
next. Refer to the
“REGISTRATION
MANUAL FOR
IMMOBILIZER”.
Step Check Yes No

IM (diag)-22
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
IMMOBILIZER (DIAGNOSTICS)
E: DTC P1574 KEY COMMUNICATION FAILURE
DTC DETECTING CONDITION:
Failure of body integrated unit to verify key (transponder) ID code
Step Check Yes No
1CHECK BODY INTEGRATED UNIT FUNC-
TION.
Insert the key to ignition switch (LOCK posi-
tion), and measure the changes in voltage
between antenna connectors.
Connector & terminal
(B142) No. 1 (+) — No. 2 (–):
Is the voltage –30 to 30 V?
(Approx. 0.1 second after
inserting the key) Is the voltage
0 V? (Approx. 1 second after
inserting the key)
Go to step 2.Replace the body
integrated unit
Body Integrated
Unit.> and replace
all the ignition keys
(including tran-
sponder). Execute
the registration
procedure next.
Refer to the “REG-
ISTRATION MAN-
UAL FOR
IMMOBILIZER”.
2CHECK IGNITION KEY (TRANSPONDER).
1) Remove the key from ignition switch.
2) Start the engine using other key which is
already registered.
Does the engine start? Replace all the
ignition keys
(including tran-
sponder). Execute
the registration
procedure next.
Refer to the “REG-
ISTRATION MAN-
UAL FO R
IMMOBILIZER”.
Replace the body
integrated unit
Body Integrated
Unit.> and replace
all the ignition keys
(including tran-
sponder). Execute
the registration
procedure next.
Refer to the “REG-
ISTRATION MAN-
UAL FOR
IMMOBILIZER”.

IM (diag)-23
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
IMMOBILIZER (DIAGNOSTICS)
F: DTC P1576 EGI CONTROL MODULE EEPROM
DTC DETECTING CONDITION:
•ECM malfunctioning
•Failed to access ROM inside ECM, while performing teaching operation on the keys.
G: DTC P1577 IMM CONTROL MODULE EEPROM
DTC DETECTING CONDITION:
•Body integrated unit malfunctioning
•Failed to access ROM inside the body integrated unit.
Step Check Yes No
1PERFORM TEACHING OPERATION OF IG-
NITION KEY.
Perfor m teaching operation on all keys of the
vehicle. Refer to the “REGISTRATION MAN-
UAL FOR IMMO BILIZER”.
Is the teaching operation for all
keys completed?
Make sure it is
possible to start
the engine with all
keys that have
been taught. This
completes the
work.
Go to step 2.
2PERFORM TEACHING OPERATION OF IG-
NITION KEY.
Perfor m teaching operation on all keys of the
vehicle. Refer to the “REGISTRATION MAN-
UAL FOR IMMO BILIZER”.
Is the teaching operation for all
keys completed?
Make sure it is
possible to start
the engine with all
keys that have
been taught. This
completes the
work.
Go to step 3.
3PERFORM TEACHING OPERATION OF IG-
NITION KEY.
Perfor m teaching operation on all keys of the
vehicle. Refer to the REGISTRATION MAN-
UAL FOR IMMO BILIZER.
Is the teaching operation for all
keys completed?
Make sure it is
possible to start
the engine with all
keys that have
been taught. This
completes the
work.
Replace the ECM.
FU(H6DO)-32,
INSTALLATION,
Engine Control
Module (ECM).>
Step Check Yes No
1PERFORM TEACHING OPERATION OF IG-
NITION KEY.
Perfor m teaching operation on all keys of the
vehicle. Refer to the “REGISTRATION MAN-
UAL FOR IMMO BILIZER”.
Is the teaching operation for all
keys completed?
Make sure it is
possible to start
the engine with all
keys that have
been taught. This
completes the
work.
Go to step 2.
2PERFORM TEACHING OPERATION OF IG-
NITION KEY.
Perfor m teaching operation on all keys of the
vehicle. Refer to the “REGISTRATION MAN-
UAL FOR IMMO BILIZER”.
Is the teaching operation for all
keys completed?
Make sure it is
possible to start
the engine with all
keys that have
been taught. This
completes the
work.
Go to step 3.
3PERFORM TEACHING OPERATION OF IG-
NITION KEY.
Perfor m teaching operation on all keys of the
vehicle. Refer to the REGISTRATION MAN-
UAL FOR IMMO BILIZER.
Is the teaching operation for all
keys completed?
Make sure it is
possible to start
the engine with all
keys that have
been taught. This
completes the
work.
Replace the body
integrated unit.
INSPECTION,
Body Integrated
Unit.>

IM (diag)-24
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
IMMOBILIZER (DIAGNOSTICS)
H: DTC P1578 METER FAILURE
DTC DETECTING CONDITION:
Reference code incompatibility between body integrated unit and combination meter
1. CHECK LAN COMMUNICATION SYSTEM.
Inspect LAN communication system in the following situation. dure.>
•DTC of body integrated unit B0300, B0301, B0302, B0111 or B0321 is displayed.
•“Er IU” or “Er LC” is displayed in combination meter odo/trip meter.
2. REPLACE COMBINATION METER.
Replace the combination meter. Execute the registration
procedure of all immobilizer part (combination meter and etc.) next. Refer to the “REGISTRATION MANUAL
FOR IMMOBILIZER”.
NOTE:
When the combination meter has been replaced, be sure to perform the registration procedure of immobiliz-
er.

IDI-4
Combination Meter System
INSTRUMENTATION/DRIVER INFO
2. Combination Meter System
A: WIRING DIAGRAM
1. COMBINATION METER
Meter System.>
B: INSPECTION
1. SELF-DIAGNOSIS
The self-diagnosis (checking of each meter, warn-
ing light, indicator, illumination, LCD, buzzer
sound) of combination meter can be performed in
the following procedure.
1) Turn the ignition switch to ON while turning the
small light to OFF.
2) Step 1) Turn the small light switch to ON within 3
seconds after step 1), then press the odo/tripmeter
knob three times.
3) Turn the small light switch to OFF, and press the
odo/trip knob three times.
4) Turn the small light switch to ON, and press the
odo/trip knob three times.
NOTE:
•Perform the steps described in 2) and 4) within
10 seconds after the ignition switch is turned to ON.
•When pressing the odo/trip meter knob four
times, the display changes to DTC display mode
(ECM, TCM). MODE, INSPECTION, Combination Meter Sys-
tem.>When the self-diagnosis function operates,
the warning light, indicator, and LCD display are
checked, then every press of the odo/trip meter
knob will initiate the operation checks in the order
of meter, illumination and buzzer. LIST OF SELF-DIAGNOSIS MODE OPERATION,
INSPECTION, Combination Meter System.> Turn
the ignition switch to OFF to cancel the self-diagno-
sis function.
•When the engine starts during diagnosis, the
self-diagnosis function is not cancelled, however,
once the vehicle starts driving, the self-diagnosis
function is cancelled automatically for safety.

IDI-8
Combination Meter System
INSTRUMENTATION/DRIVER INFO
5. CHECK VDCCM.
6. CHECK ENGINE CONTROL MODULE (ECM)
Step Check Yes No
1CHECK VEHICLE SPEED SIGNAL.
1) Lift up the vehicle and support it with rigid
racks.
2) Drive the vehicle faster than 10 km/h (6
MPH).
WARNING:Be careful not to get caught in the running
wheels.
3) Measure the voltage between combination
meter connector and chassis ground.
Connector & terminal
(i10) No. 27 (+) — Chassis ground (–):
Is the voltage less than 1 V
←→ 5 V or more?
Replace the meter
case assembly.
Go to step 2.
2CHECK HARNESS BETWEEN VDCCM AND
COMBINATION METER.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from VDCCM
and combination meter.
3) Measure the resistance between VDCCM
harness connector and combination meter har-
ness connector.
Connector & terminal
(B310) No. 33 — (i10) No. 27:
Is the resistance less than 10
Ω?
Check the
VDCCM. VDC(diag)-2,
Basic Diagnostic
Procedure.>
Repair the wiring
harness.
Step Check Yes No
1CHECK ECM SIGNAL.
1) Start the engine.
2) Measure the voltage between ECM con-
nector and chassis ground.
Connector & terminal
(B136) No. 11 (+) — Chassis ground (– ):
Is the voltage 0 ←→ 14 V or
more?
Go to step 2.Inspect the ECM.
EN(H6DO)(diag)-
2, Basic Diagnos-
tic Procedure.>
2CHECK HARNESS BETWEEN COMBINA-
TION METER AND ECM.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM and
combination meter.
3) Measure the resistance between ECM har-
ness connector and combination meter har-
ness connector.
Connector & terminal
(B136) No. 11 — (i10) No. 28:
Is the resistance less than 10
Ω?
Replace the meter
case assembly.
Repair the wiring
harness.