2009 Peugeot 206 P Dag Owner's Manual

i
76
CHANGING A BULB
Front lights

1. Direction indicators
(PY21 W amber).

2. Side lights (W 5 W).

3. Dipped headlamps (H7-55 W).

4. Main beam headlamps (H1-55 W).

5. Fog lamps (PSX-24 W).
Operating procedure for replacing a
faulty bulb with a new bulb. These
operations must be carried out
with the
ignition off .
To gain access to the bulbs on the right-
hand side:
- Remove the screenwash reservoir fi ller tube.
- Unclip the engine harness 1 .
- Remove the nut from the engine control unit support 2 using a size
10 spanner.
- Remove the engine control unit and support assembly. After changing the faulty bulb:
- Slide the two lugs of the control unit
support into the locations A .
- Put the engine control unit back in place.
- Tighten the engine control unit sup- port nut (size 10 spanner).
- Reclip the engine harness.
These bulbs are available from
PEUGEOT dealers.
In certain climatic conditions (low
temperature, humidity), conden-
sation inside the glass of the
headlamps and lights is normal .
However, contact a PEUGEOT
dealer if water is present in the
headlamps.

i
77

 Turn the bulb holder a quarter turn
and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specifi cation and colour.
Direction indicators

 Disconnect the headlamp main con-
nector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Pull the bulb and change it. Dipped headlamps

 Disconnect the headlamp main con-
nector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Press the connector downwards to
release the bulb.

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Side lights

!
78
Front fog lamp

 Slide a hand under the bumper.

 Turn the connector a quarter turn
and remove the assembly.

 Remove the bulb and change it.
Main bean headlamps

 Disconnect the headlamp main con-
nector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Move aside the springs to release
the bulb and pull the bulb.
To refi t, carry out these operations in
reverse order. Direction indicator side repeater

 Push the repeater forwards and
release it.

 Remove the repeater and change it.
Repeaters can be obtained from a
PEUGEOT dealer.

High pressure washing
When using this type of washing
on stubborn dirt, do not persist
on the headlamps, the lights and
their surround to avoid damaging
their coating and their seal.

79
Third brake light 5 bulbs W 5 W
Unclip the boot side trim.
Remove the wing nut.
Release the light unit from the outside.
Press the lug A and disconnect the con-
nector.
Remove the sealing foam.
Move aside the tabs B and remove the
bulb holder.
Turn the faulty bulb a quarter turn and
change it.
To refi t, carry out these operations in
reverse order and ensure that the bulb
holder, the light and the foam cover are
repositioned correctly. Using a 10 mm spanner, unscrew the
2 nuts
A .
Release the light unit.
Squeeze the two tabs B to release the
bulb holder.
Change the faulty bulb.

1. Direction indicators
(P21 W amber).

2. Reversing lights P21 W.

3. Brake lights/side lights
(P21/5 W).

4. Fog lamp (P21 W).
Rear lights

80
Rear fog lamp (P21 W)
The fog lamp is located on the rear
bumper, on the left-hand side.
Unscrew the lamp and release the as-
sembly.
Turn the pin connector a quarter turn
and remove it.
Change the bulb. Number plate lights W 5 W
Insert a thin screwdriver into one of the
outer holes of the transparent cover.
Push it outwards to unclip it.
Remove the transparent cover.
Change the faulty bulb.

81
CHANGING A FUSE
Operating procedure for replacing a
faulty fuse with a new fuse to rectify a
failure of the corresponding function.
The fuse boxes are located under the
fascia and in the engine compartment.
Fascia fuse box
Unscrew the catch a quarter turn using
a coin then remove the cover to gain
access to the fuses.
The spare fuses and the pliers A are
secured on a removable support fi xed
horizontally inside the fascia fuse box. Removing and fi tting a fuse
Before changing a fuse, the cause of the fault must be fou
nd and remedied. The
fuse numbers are indicated on the fuse box.
Use the pliers A .

Always replace a faulty fuse with a fuse of the same rating .
Pliers A

Correct Incorrect

81
CHANGING A FUSE
Operating procedure for replacing a
faulty fuse with a new fuse to rectify a
failure of the corresponding function.
The fuse boxes are located under the
fascia and in the engine compartment.
Fascia fuse box
Unscrew the catch a quarter turn using
a coin then remove the cover to gain
access to the fuses.
The spare fuses and the pliers A are
secured on a removable support fi xed
horizontally inside the fascia fuse box. Removing and fi tting a fuse
Before changing a fuse, the cause of the fault must be fou
nd and remedied. The
fuse numbers are indicated on the fuse box.
Use the pliers A .

Always replace a faulty fuse with a fuse of the same rating .
Pliers A

Correct Incorrect

82

Fuse N° Rating
Functions
1 - Not used
4 20 A Multifunction display - Boot lighting - Audio equipment - Steering wheel controls - Trailer
5 - Not used
6 10 A Coolant level - Audio equipment
7 15 A Driving school accessory - Alarm fi tted as an accessory
9 - Not used
10 40 A Rear screen demisting 11 15 A Rear windscreen wiper
12 30 A Front electric windows
14 10 A Engine fuse box - Air bags - Steering wheel con trols - Rain sensor
15 15 A Instrument panel - Multifunction display - Air conditioning - Audio equipment
16 30 A Locking/unlocking controls for doors, bonnet a nd boot
20 10 A Right-hand brake light
21 15 A Left-hand brake light - 3rd brake light
22 20 A Front courtesy light - 12 volt accessories socket
S1 Shunt PARC shunt