2009 Peugeot 206 P Dag Owner's Manual

ii
19
Coolant temperature indicator
System which informs the driver of the
changes in the temperature of the en-
gine coolant while driving.
With the engine running, when the needle
is:
- in zone A , the temperature is correct,
- in zone B , the temperature is too
high; the max temperature warning
light 1 and the central STOP warn-
ing light come on, accompanied by
an audible signal and a message on
the multifunction display.

You MUST stop as soon as it is safe
to do so.
Consult a PEUGEOT dealer. After driving for a few minutes, the tem-
perature and pressure in the cooling
system increase.
To top up the level:

 wait for the engine to cool,

 unscrew the cap by two turns to
allow the pressure to drop,

 when the pressure has dropped,
remove the cap,

 top up the level to the "MAX" mark
(circular line).
On petrol engines, the cooling of
the engine is managed electroni-
cally to improve consumption. Con-
sequently, the coolant temperature
levels are no longer simply linked
with the external ambient condi-
tions and the use of the vehicle.
For example, in town, it is normal
for the coolant temperature to be
slightly higher in cold weather than
in hot weather.

20
Maintenance indicator
System which informs the driver when
the next service is due, in accord-
ance with the manufacturer's servicing
schedule.
The point at which the service is due is
calculated from the last indicator zero
reset. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service. More than 620 miles (1 000 km)
remain before the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.

Example: 4 800 miles/km remain be-
fore the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances. Less than 620 miles (1 000 km)
remain before the next service is due

Example: 560 miles (900 km) remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains on to indicate that a service
must be carried out soon.

ii
ii
21
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.
Maintenance indicator zero reset
After each service, the maintenance
indicator must be reset to zero.
The procedure for resetting to zero is as
follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the distance
recorder display begins a count-
down,

 when the display indicates "=0" ,
release the button; the spanner dis-
appears.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes to
indicate that the service must be carried
out as soon as possible.

Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains lit .

22
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life. Lighting rheostat
System for manual adjustment of the
brightness of the instrument panel in
relation to the exterior brightness.
The total and trip distances are displayed for thirty seconds when the ignition is
switched off, when the driver's door is
opened and when the vehicle is locked
or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

 With the ignition on, press the button
until zeros appear. Activation
When the lights are on:

 press the button to change the
brightness of the instrument panel,

 when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or

 when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,

 when the lighting reaches the level
of brightness required, release the
button.
Deactivation
When the lights are off, pressing the
button does not have any effect.

23
MONOCHROME DISPLAY A Adjusting the parameters
Press and hold button 1 for two seconds
to access the settings; the data fl ashes,
indicating it is ready to be modifi ed.
Then, each press of button 1 scrolls
through the various data in the follow-
ing order:
- language of information displayed,
- hours (12 then 24 hour mode),
- minutes,
- year,
- month,
- day,
- unit of temperature (degrees Cel- sius or Fahrenheit).
Pressing button 2 allows modifi cation
of the data selected. Press and hold for
rapid advance (return to start after the
last possible value).
After 7 seconds with no action, the main
display returns; the modifi ed data are
now recorded.

Note: Pressing button 2 briefl y displays
the outside temperature for a few seconds.
When the outside temperature is be-
tween -3° and 3°C, the outside tempera-
ture display on the screen takes priority
over the clock display.
This displays the following information:
- the time,
- the date,
- the outside temperature * (this fl ashes
when it is between -3 and 3°C),
- the audio system displays,
- a door check (e.g.: ''left front door open''),
- warning messages (e.g. ''remote control battery fl at'') or information
messages (e.g. ''economy mode
active''), displayed temporarily.
* With automatic air conditioning only.

24
MONOCHROME DISPLAY B
This enables the following information
to be displayed:
- the time,
- the date,
- the outside temperature * (this fl ash-es when it is between -3 and 3 °C),
- the status of the doors. The display shows you, by means of a graphic,
whether a door is open,
- the warning messages (e.g. ''battery charge fault'') or information mes-
sages (e.g. "fuel level low''), dis-
played temporarily, can be cleared
by pressing button 1 or 2 ,
- the trip computer. Setting the parameters
Press button
1 for two seconds to ac-
cess the settings. The information fl ashes
to show it is ready to be modifi ed.
Then, individual presses on button 1
allow you to scroll through the various
data in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (degrees Cel- sius or Fahrenheit),
- time format (12 then 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button 2 allows you to change
the information selected. Maintain the
pressure for rapid scrolling.
After 7 seconds without operation, the
screen returns to the normal display
and the modifi ed data is recorded.
* With automatic air conditioning only.

25
Display B
TRIP COMPUTER
Zero reset
Press the stalk for more than two seconds.
Range
This shows the distance that can still be
covered with the fuel remaining in the
tank.

Note: this fi gure may increase if there
is a change in the style of driving or the
road surface, producing a signifi cant
drop in current consumption.
When the range is less than 20 miles
(30 km), three segments are dis-
played. After fi lling with fuel, the range
is displayed when it exceeds 60 miles
(100 km).
If horizontal segments are displayed for
long periods instead of digits, contact a
PEUGEOT dealer.
Pressing the button on the end of the

wash/wipe stalk enables the following
data to be displayed:
- the range
- the distance travelled
- the average consumption
- the current consumption
- the average speed Average consumption
This is the average fuel consumption
since the computer was last set to zero.
Current consumption
This is the average quantity of fuel con-
sumed during the last few seconds.
This function is displayed only when the
vehicle is travelling at a speed greater
than 20 mph (30 km/h). Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
Average speed
This is the average speed calculated
since the computer was last set to zero
(with the ignition on).

26
VENTILATION
System which creates and maintains
comfortable conditions in the vehicle's
passenger compartment.
Air treatment
The incoming air follows various routes
depending on the controls selected by
the driver:
- direct arrival in the passenger com-partment (air intake),
- passage through a heating circuit (heating),
- passage through a cooling circuit (air conditioning). The temperature control enables you to
obtain the level of comfort required by
mixing the air of the various circuits.
The air distribution control enables you
to diffuse the air in the passenger com-
partment combining several air vents.
The air fl ow control enables you to in-
crease or reduce the speed of the ven-
tilation blower.
The air circulating in the passenger
compartment is fi ltered and originates
either from the outside via the grille lo-
cated on the bonnet or from the inside
in air recirculation mode.
Control panel
The controls of this system are grouped
together on the centre console. De-
pending on the model, the functions of-
fered are:
- the level of comfort required,
- the air fl ow,
- the air distribution,
- the de-icing and demisting,
- the manual or automatic air condi-
tioning controls.
Air diffusion

1. Windscreen de-icing or demisting
vents.

2. Front side window de-icing or de-
misting vents.

3. Side adjustable and closing vents.

4. Central adjustable and closing vents.

5. Air outlets to the front footwells.

6. Lower air outlets (under the front
seats) * .
*
Only operational with automatic air
conditioning.