2009 OPEL MERIVA lock

129
Driving and operation
Driving and operation
Manual transmission
automated
3
The manual transmission automated
transmission 3 permits manual ( manual
mode ) or automatic gear shifting
(automatic mode ), both with automatic
clutch control.
Picture no: 17878s.tif
Transmission display
Shows the mode and current gear.
If the Winter programme is activated, T is
illuminated.
Manual transmission automated
3... 129
Manual transmission ........................... 134
Driving hints ......................................... 135
Saving fuel, protecting the environment ...................................... 137
Fuels, refuelling .................................... 139
Catalytic converter, exhaust gasses .. 142
Drive Control Systems ......................... 146
Hydraulic brake system ...................... 151
Anti-lock brake system (ABS u ) ........ 152
Hand brake .......................................... 153
Brake assist .......................................... 153
Hill Start Assist 3 (HSA) ...................... 153
Wheels, tyres ........................................ 153
Roof rack 3.......................................... 158
Towing equipment 3........................... 158
Towing equipment with removable coupling ball bar 3........................... 159
Caravan/trailer towing ........................ 162

134 Driving and operation
Picture no: 14721s.tif
Interruption of power supply
The clutch is not disengaged if there is an
interruption of the power supply when a
gear is engaged. The vehicle cannot move.
If the battery is flat, start the car using
jump leads 3166.
If the cause is not a flat battery, contact a
workshop for assistance. If the vehicle has
to be moved out of flowing traffic,
disengage clutch.
1. Apply hand brake and switch off ignition.
2. Open bonnet and engage support. 3. Clean transmission around the cap (see
Fig.) so that no dirt can get into the
opening when the cap is removed.
4. Rotate cap to slacken and remove by lifting upwards – see figure.
5. Turn the adjusting screw clockwise using a flathead screwdriver (vehicle tools 3
3 171) until clear resistance can be felt.
The clutch has now been disengaged.
6. Fit cleaned cap again. The cap must be in full contact with the housing.
Contact a workshop for assistance
immediately.
Picture no: 15270s.tif
Manual transmissionTo engage reverse, with the vehicle
stationary wait 3 seconds after declutching
and then pull up the bu tton on the selector
lever and engage the gear.
If the gear does not engage, set the lever in
neutral, release the clutch pedal and
depress again; then re peat gear selection.
Do not grind the clutch unnecessarily.
When operating, depress the clutch pedal
completely. Do not use the pedal as a foot
rest (increases clutch wear).
Caution
Do not turn beyond the resistance, since
this can damage the Easytronic.
Caution
Towing the vehicle and starting the
engine is not permitted when the clutch
has been released in this way, although
the vehicle can be moved a short
distance.

141
Driving and operation
Picture no: 14191s.tif
Fuel filler neck at right rear side of vehicle.
The tank flap is locked together with the
doors 330.
Open tank flap.
Unscrew the fuel filler cap, remove and
suspend from the tank flap.
The fuel tank has a limiting system which
prevents overfilling of the tank. Correct filling depends to a large extent on
proper operation of
the fuel dispensing
pump:
1. Fully insert the pump nozzle and switch it on.
2. After automatically switching off, the specified tank capacity is achieved by
means of metered re fuelling (twice).
Insert fuel dispensing pump as far as
possible.
To close, place fuel filler cap in position and
turn, overcoming the resistance until the
ratchet on the cap engages audibly. Close fuel tank cover.
Caution
Wipe off any overflowing fuel
immediately.

152 Driving and operationFor vehicles with manual transmission
automated 3, the control indicator flashes
for a few seconds when the ignition is
turned off when the hand brake is not
applied. Anti-lock brake system (ABS
u)
ABS prevents the wheels from locking.
ABS starts to regulate brake pressure as
soon as a wheel shows a tendency to lock.
The vehicle remains steerable, even during
hard braking.
ABS control is made apparent though a
pulse in the brake pedal and the noise of
the regulation process.
For optimum braking, keep the brake
pedal fully depresse d throughout the
braking process, despite the fact that the
pedal is pulsating. Do not reduce the
pressure on the pedal.
Picture no: 17895s.tif
Control indicator u for ABS
It illuminates for a few seconds when
ignition is switched on. Once the control
indicator goes out, the system is ready for
operation.
If the control indica tor does not go out
after a few seconds, or if it illuminates while
driving, there is a fault in the ABS. The
brake system remains operational without
ABS regulation.
Adaptive brake lamp 3
During full-on braking, all three brake
lamps flash for the duration of ABS control. Self testing
When the engine is started and the vehicle
starts off, the system performs a self-check,
which may be audible.
Fault
Have cause of fault remedied by a
workshop. The system’s integrated self
diagnostics allow faults to be quickly
remedied.
9 Warning
If there is a fault in the ABS, the wheels
may be liable to lock due to braking that
is heavier than normal. The advantages
of ABS are no longer available. During
hard braking, the vehicle can no longer
be steered and may swerve.

157
Driving and operation
Winter tyres 3
Notes on fitting new tyres 3 154.
Restrictions 3228.
Winter tyres improve driving safety at
temperatures below 7 C.
The design of summer tyres means they
have limited qualities for winter driving.
In accordance with country-specific
regulations, affix the speed sticker 3 in the
driver’s field of view.
If you use the spare wheel when it is fitted
with a summer tyre, the vehicle’s
driveability may be affected, especially on
slippery road surfaces. Obtain a
replacement for the faulty tyre as soon as
possible, and have the wheel balanced
and fitted to the vehicle.
Wheel covers 3
Use of wheel trims and tyres that approved
by Opel for the vehicle in question and
thereby fulfil all requirements for the wheel
and tyre combination.
If the wheel trims and tyres used are not
Opel-approved, the ty res must not have a
beaded edge. Wheel trims must not impair brake cooling.
Remove the wheel trims if fitting tyre
chains
3.
Picture no: 6459u.tif
Tyre chains 3
Restrictions and further information 3 228.
Tyre chains are only permitted on the
driven wheels (front axle). They must be
fitted to the tyres symmetrically in order to
achieve a concentric fit.
Always use fine mesh chains that add no
more than 10 mm to the tyre tread and the
inboard sides (including chain lock).
9 Warning
Use of unsuitable tyres or wheel trims
could lead to sudden loss of air and
thereby accidents.

159
Driving and operation
Picture no: 14195s.tif
Towing equipment with
removable coupling ball bar
3
Stowage of coupling ball bar
The coupling ball bar is located in a bag
with the vehicle tools housed under the
spare wheel - see Fig. above.
Spare wheel 3 3172.
On vehicles with tyre repair kit 3, the
coupling ball bar is located in the left
stowage compartment beneath the floor
cover in the luggage compartment 3162,
Fig. 17923 S.
Picture no: 15271s.tif
Fitting the coupling ball bar
Fold down the socket. Remove the sealing
plug from the hole for the coupling ball bar
and stow it in the luggage compartment.
Picture no: 12416t.tif
Checking the tensioning of the coupling ball bar

z Red marking on rotary knob must point
towards white marking on coupling ball
bar.
z The gap between the rotary knob
and the coupling ball bar must be
approx. 4 mm.
z Key in the lock must be at position 1.
Caution
The coupling ball bar is to be removed
when not towing.

160 Driving and operation
Picture no: 12417t.tif
Otherwise, the coupling ball bar must be
tensioned before it is inserted into the
coupling housing:
zUnlock coupling ball bar by turning key
to position 1 3 159, Fig. 12416 T.
z Pull out rotary knob and turn clockwise
as far as it will go, see Fig.
Picture no: 12418t.tif
Inserting the coupling ball bar

Insert the tensioned coupling ball bar in the
housing and push firmly upwards until it
audibly engages.
The rotary handle snaps back into its home
position resting against the coupling ball
bar (no gap).
Picture no: 16484s.tif
Lock the coupling ball bar in position by
turning key to position 2 3 159,
Fig. 12416 T. Remove the key and press the
protective flap into place.
When the coupling ball bar is locked the
turn knob can no longer be pulled out.
9 Warning
Do not touch rotary handle during
insertion.

161
Driving and operation
Check that the coupling ball bar is correctly installedzGreen marking on rotary knob must
point towards white ma rking on coupling
ball bar
z There must be no gap between the
rotary handle and the coupling ball bar
z The coupling ball bar must be firmly
engaged in the opening
z The coupling ball bar must be locked
and the key removed
Picture no: 12421t.tif
Eye for break-away stopping cable
In the case of trailers/caravans with brakes,
attach breakaway stopping cable to eye.
Picture no: 13670t.tif
Dismounting the coupling ball bar
Open the protective flap and turn the key
to position 1 to unlock the coupling ball bar
3 159, Fig. 12416 T.
Pull out rotary handle and turn clockwise
as far as it will go. Pull out coupling ball bar
downwards.
Insert the sealing plug in the opening for
the coupling ball bar. Close the socket
3 159, Fig. 15271 S.
9 Warning
Towing a caravan/trailer is only
permitted with a properly fitted coupling
ball bar. If the coupling ball bar cannot
be correctly fitted, please contact a
workshop for assistance.