2009 OPEL MERIVA lock

95
Instruments, Controls
Automatic time synchronisation
3
The RDS signal of most VHF transmitters
automatically sets the time.
Some transmitters do not send a correct
time signal. In such cases, we recommend
that you switch off automatic time
synchronisation.
On infotainment systems with
navigation 3, time and date are also
harmonised upon receipt of a GPS satellite
signal.
The function is activated by ticking the field
in front of Synchron. clock automatical. in
the Time, Date menu.
Picture no: 16714t.tif
Language selection
You can select the display language for
some functions.
Select menu item Language from the
Settings menu.
The available langua ges are displayed.
Picture no: 16715t.tif
Select the desired language.
Selections are indicated by a 6 in front of
the menu item.
In systems with language version 3, when
the language setting of the display is
changed, the system will ask if the message
language should also be changed - see
infotainment system instructions.
7
Settings 19,5° 19:36
Time, Date
Language Deutsch
Units English
Contrast Español
Day / Night Nederlands
! Ign. logic Français
7
13 Languages 19,5° 19:36!
Deutsch
English
Español
Nederlands
Français
Italiano

107
Lighting
Picture no: 14302s.tif
Lead-me lighting
3
Lead-me lighting when leaving the
vehicle 3
The dipped headlamps come on for
around 30 seconds after switching on and
closing the driver’s door.
To activate:
1. Switch off ignition.
2. Remove ignition key.
3. Open driver’s door.
4. Pull turn signal stalk toward steering
wheel.
5. Close driver’s door. If the driver’s door is left open, the lamps
will go out after two minutes.
The light is switched off immediately by
inserting the key into
the ignition or pulling
the turn signal stalk towards the steering
wheel again.
Picture no: 17920S.tif
Lead-me lighting when opening the
vehicle 3
The Lead-me-to-the-car lighting function
allows the dipped headlamps to be lit for
around 30 seconds using the remote
control.
This function must be activated (once):
Unlock the vehicle, put the key in the
ignition and press the light switch for
approx. 5 seconds - see next page,
Fig. 14136 S.
To deactivate the function permanently,
contact a workshop.

108 LightingTo activate the lead-me-to-the-car light
function, press button q on the remote
control twice with the vehicle locked.
Country-specific version 3: to enable the
lead-me-to-the-car function, press
button q on the remote control once with
the vehicle locked.
The lead-me-to-the-car light function is
deactivated immediately by pressing
button p of the remote control or
switching on the ignition.
Picture no: 14759s.tif
Instrument illumination
k,
Information display illumination
Lights come on when ignition is switched on.
Brightness can be adjusted when the
exterior lights are on: Push to release knob
k and then turn it clockwise or
anticlockwise and hold until the desired
brightness is obtained.
Display mode 3 396.
Picture no: 14136s.tif
Courtesy lamp Automatic interior light
Comes on automatically when the vehicle is
unlocked with the radi o remote control or
when a door is opened.
Goes off automatically after a delay when
the doors are closed or immediately when
the ignition is switched on or the doors are
locked.
Front courtesy lamp
To operate manually from inside when the
doors are closed: on = Press light switch 0
off = Press light switch 0 again

109
Lighting
Picture no: 11607s.tif
Front reading lamps 3
Operate using buttons with the ignition
switched on.
Picture no: 12344t.tif
Courtesy lamps and rear reading lamps 3
Centre switch position: The rear courtesy
lamp comes on together with the front one
when a door is opened.
The rear reading lamps on the left and
right can be switched on separately. With
ignition on: Entry lighting
3
After unlocking the vehicle, the instrument
and switch illumination plus the courtesy
lamps come on for a few seconds.
Illuminated mirror in the sun visors 3
The lighting switches on when the cover is
opened.
Glove compartment lighting 3
The glove compartment light comes on
when the ignition is on and the lid is
opened.
Luggage compartment lighting 3
The luggage compartment light comes on
when the tailgate is open.
Automatically regulated centre console
lighting 3
Spotlight in housing of interior mirror.
Daylight-dependent, automatically
regulated centre console lighting with
ignition switched on. On = Switch position I
Off = Switch position 0

117
Climate control
Picture no: 14150s.tif
Ventilation
zSet the temperature to the desired
setting.
z Switch fan on, select fan setting
according to requirements.
z For maximum ventilation in head area:
set air distribution switch to M and open
all vents.
z For ventilation to foot well: Set air
distribution switch to K.
z For simultaneous ventilation to the head
area and the foot well: Set air
distribution switch to L. Heating
For rapid warming of the passenger
compartment:
z
Turn the temperature switch clockwise as
far as it will go (warm).
z Set the fan to speed 3.
z Set air distribution switch to desired
position, preferably position J, 3 116. The comfort and general well-being of the
vehicle occupants are to a large extent
dependent on a suitab
le ventilation and
heating setting.
To achieve stratifica tion of temperature
with a pleasant "cool head and warm feet"
effect, set the rotary air distribution switch
to K, J or L, set temperature rotary
switch to any position (in centre range with
temperature stratification effect).

118 Climate control
Picture no: 14151s.tif
Heating the foot well
zSet the temperature switch in the right-
hand zone.
z Switch on fan.
z Set air distribution switch to K.
Picture no: 16481s.tif
Demisting and defrosting windows
Misted or icy windows, e. g. due to damp
weather, damp clothing or low outside
temperatures:
z Turn the temperature switch clockwise as
far as it will go (warm). z
Set fan to 3 or 4 .
z Set air distribution switch to V.
z Switch on heated rear window Ü 3.
z Open side air vents as required and
direct them towards door windows.
z For simultaneous footwell heating, set
air distribution switch to J.
9 Warning
Disregard of the instructions could lead
to misting or icing of the windows and
subsequent accidents due to impaired
visibility.

121
Climate control
Picture no: 14162s.tif
Maximum cooling
Briefly open windows, sun roof and tilting
roof 3 so that warm air can escape quickly.
z Cooling n on
z Air recirculation system 4 on
z Turn the temperature switch
anticlockwise as far as it will go (cold)
z Set fan to 4
z Set air distribution switch to M
z Open all air vents
Picture no: 16482s.tif
Demisting and defrosting windows
Misted or icy windows, e. g. due to damp
weather, damp clothing or low outside
temperatures: z
Cooling n on, the air conditioning
compressor automatically switches itself
off at low outside temperatures (icing).
z Turn the temperature switch clockwise.
z Set fan to 3 or 4 .
z Air distribution switch to V, air
recirculation system 4 automatically
switches off,
– or –
if there is still moisture in the system after
previous air conditioning operation, the
windows may mist up. To prevent this,
set air distribution to K before starting
engine and set to V approx. 5 seconds
after starting.
z Activate heated rear window Ü.
z Open side air vents as required and
direct them towards the side windows.
9 Warning
Disregard of the instructions could lead
to misting or icing of the windows and
subsequent accidents due to impaired
visibility.

125
Climate control
Picture no: 16503s.tif
Activating and deactivating air
conditioning compressor
Press the ECO button. ECO appears in the
air conditioning display.
Switch on to sa ve fuel. In this m ode cooling
(AC compressor) is switched off.
Inflowing air is neither cooled nor
dehumidified. This restricts the level of
comfort provided by the automatic climate
control system. This may cause the
windows to mist up, for example.
When cooling operates, condensation
forms and drips from the underside of the
vehicle.
To return to cooling operation: press
ECO button. ECO goes out.
Picture no: 16504s.tif
Air distribution
Press one or more of the following buttons.
The corresponding symbol appears in the
air conditioning display:
To return to automatic mode: Press the
appropriate buttons again, or press AUTO.
Picture no: 16505s.tif
Air flow
Set air flow using the right-hand rotary
knob. The selected fan speed is indicated
by the number of bars.
To deactivate the fan and thereby the
automatic climate control system: Turn the
right-hand rotary knob anticlockwise until
the display goes out.
Switching on: turn rota ry knob clockwise.
To return to automatic mode: Press
AUTO button.
sAir distribution towards windscreen
and front door windows.
M Air distribution towards vehicle
occupants via adjustable vents.
K Air distribution towards footwell.