2009 OPEL CORSA Owners Manual

163
Driving and operation
To deactivateThe system deactivates automatically
when reverse gear is disengaged.
If the system is switched of with reverse
gear engaged, press button r 3, the LED
in the button goes out.
To reactivate, press button r again.
Picture no: 18255s.tif
Control indicator
r
Illuminates:
Fault in system. The system is not
operational. Have cause of fault remedied
by a workshop. The system’s integrated
self diagnostics allows faults to be quickly
remedied.
Flashes:
The fault is due to sensors obstructed with
snow or ice. The sensors must be
undamaged and free of dirt, snow and ice.
Interference due to external sources of
ultra sound (e.g. pneumatic drills, rotary
machines). Once the source of interference
is removed, the system will operate
normally. Caravan/trailer towing equipment
3,
caravan/trailer towing When towing, park pilot is automatically
deactivated when the trailer cable is
plugged into the socket.
Fitting rear load racks
3
Rear carriers, e. g. bike carriers, could
cause system malfunction.
Back to overview

164 Driving and operation
Picture no: 18244s.tif
Deflation detection system (DDS)3
The deflation detection system monitors
the revolutions of all four vehicles from a
speed of approximately 30 km/h. If there is
a loss of pressure in one of the tyres, its
diameter is reduced, and therefore also the
wheel rotation speed. Warning lamp w
lights red.
Stop immediately and check tyre pressure.
Fit the spare wheel if necessary 3 196,
3 200. Control indicator
w

If control indicator w lights up red while
driving, there is a loss of pressure. Stop
immediately and check tyre pressures. A
maximum speed of 80 km/h is permitted
for tyres run flat 3 3 171.
Control indicator illumination w in yellow
indicates a fault in the system. Have cause
of fault remedied by a workshop. The
system’s integrated se lf diagnostics allow
faults to be quickly remedied.
The control indicator flashes three times
when the system is initialising.
Tyre pressure 3169, 3264.
Picture no: 18245s.tif
System initialisationAfter correcting the tyre pressure or
changing a tyre/wheel, the system must be
initialised: turn the ignition on, press the
DDS button for approx. 4 seconds. Control
indicator w flashes three times. The system
is operational after driving a certain
distance.
Only initialise the system if all tyres have
the prescribed pressure.
9
Warning
The deflation detection system does not
replace manual checks with a suitable
gauge.
Check tyre pressures at least every
14 days and prior to any long journey;
the tyres should be checked when cold.
Don’t forget to check the spare 3.
Back to overview

165
Driving and operation
Picture no: 17206t.tif
Hydraulic brake system The foot brake comprises two independent
brake circuits.
If a brake circuit fails, the vehicle can still be
braked using the other brake circuit.
However, the brake pedal must be
depressed a considerable way before any
braking effect occurs, and much more
force is required. The braking distance is
longer. Contact a workshop for assistance
before continuing to drive. To ensure that full
pedal travel can be
utilised, especially in case of a fault in one
of the brake circuits, there must be no mats
in the vicinity of the pedals 3150.
When the engine is not running, the
support of the brake servo unit disappears
once the brake pedal has been depressed
once or twice. Braking effect is not
reduced, but braking requires significantly
greater force. This is especially important
to bear in mind when towing.
The brake fluid level should be checked
regularly. If the brake fluid level is too low
and the hand brake is not applied, control
indicator R on the instrument panel
illuminates 389.
Picture no: 18257s.tif
Brake system control indicator R
The control indicator lights up when the
ignition is switched on when the hand
brake is applied or when the brake or
clutch fluid level is too low. Brake fluid
level 3246.
For vehicles with manual transmission
automated 3, the control indicator flashes
for a few seconds when the ignition is
turned off when the hand brake is not
applied.
9
Warning
If the control indicator illuminates when
the hand brake is released, stop driving
immediately. Contact a workshop for
assistance.
Back to overview

166 Driving and operationAnti-lock brake system (ABS
u)
ABS prevents the wheels from locking.
ABS starts to regulate brake pressure as
soon as a wheel shows a tendency to lock.
The vehicle remains steerable, even during
hard braking.
For optimum braking, keep the brake
pedal fully depressed throughout the
braking process, despite the fact that the
pedal is pulsating. Do not reduce the
pressure on the pedal.
Picture no: 18258s.tif
Control indicator u for ABS
It illuminates for a few seconds when
ignition is switched on. Once the control
indicator goes out, the system is ready for
operation.
If the control indica tor does not go out
after a few seconds, or if it illuminates while
driving, there is a fault in the ABS. The
brake system remains operational without
ABS regulation.
Adaptive brake lamp 3
During full-on braking, all three brake
lamps flash for the duration of ABS control. Self testing
When the engine is started and the vehicle
starts off, the system performs a self-check,
which may be audible.
Fault
Have cause of fault remedied by a
workshop. The system’s integrated self
diagnostics allow faults to be quickly
remedied.
9
Warning
If there is a fault in the ABS, the wheels
may be liable to lock due to braking that
is heavier than normal. The advantages
of ABS are no longer available. During
hard braking, the vehicle can no longer
be steered and may swerve.
Back to overview

167
Driving and operation
Picture no: 18256s.tif
Hand brake Always apply hand brake firmly without
pressing the release button, and apply as
firmly as possible on steep slopes.
To release the hand brake pull lever up
slightly, press release button, and lower
lever all the way down.
To reduce the operating forces of the hand
brake, depress the foot brake at the same
time.
Brake assist
3
If the brake pedal is operated quickly with
a powerful push, the vehicle is
automatically braked at full braking power
in order to achieve the shortest possible
braking distance when full-on braking
occurs (brake assist).
Maintain steady pressure on the brake
pedal for as long as full-on braking is to
continue. When the brake pedal is
released, the maximum brake force
amplification is taken away.
Hill Start Assist
3 (HSA)
The system helps pull away on inclines.
After releasing the footbrake, if the hand
brake is not applied the brakes are only
released after 2 seconds. As soon as the
acceleration is sufficient to prevent rolling
back, the brake is released.
Back to overview

168 Driving and operationWheels, tyres Suitable tyres and restrictions 3264.
Tyres fitted in the factory are adapted to
the chassis and provide optimum driving
comfort and safety.
Changing tyre/wheel type
If tyres of a different size than those fitted
at the factory are used, it may be
necessary to reprogram the electronic
speedometer and make other vehicle
modifications.
After converting to a different tyre size,
have the adhesive label with tyre pressures
replaced. Vehicles with run-flat tyres
3
When switching wheels, e.g. when
switching to winter tyres, use run-flat tyres
as there is no spare wheel or tyre repair kit
in the vehicle.
Vehicles with engine Z 10 XEP: Run-flat
tyres are not permitted for all rear axle
applications. We recommend your Opel
Partner.
Run-flat tyres 3 3171. Fitting new tyres
Fit tyres in pairs or in sets, which is even
better. Ensure that tyres on one axle are
z
the same size,
z the same design,
z the same make,
z and have the same tread pattern.
Fit directional tyres such that they roll in the
direction of travel. The rolling direction is
indicated by a symbol (e.g. an arrow) on
the sidewall.
Tyres fitted opposing the rolling direction
(e.g. when a tyre is changed) should be
refitted as soon as possible. This is the only
way to obtain full benefit from the design
properties of the tyre.
Run-flat tyres 3 m u s t n o t b e c o m b i n e d w i t h
conventional tyres.
Pay attention to legal requirements when
disposing of tyres.
9
Warning
Use of unsuitable tyres or wheels may
lead to accidents and render the vehicle
unroadworthy.
Back to overview

169
Driving and operation
Picture no: 18311s.tif
Tyre pressure
Check tyre pressure, including the spare
wheel, at least every 14 days and prior to
any long journey; the tyres should be
checked when cold. Don’t forget to check
the spare wheel 3.
Remove the valve cap key from the tank
flap and use it to unscrew the valve cap.
Tyre pressure 3264 and on the adhesive
label 3 on the inside of the tank flap.
The tyre pressure data is for cold tyres. It
applies to both summer and winter tyres. Always inflate the spare wheel
3 to the
pressure specified for full load.
Do not reduce tyre pr essure when the tyres
are warm. Otherwise the pressure may
drop below the permissible minimum when
the tyres cool down.
After having checked the tyre pressure,
tighten the valve caps using the valve cap
key.
Incorrect inflation pressures will impair
safety, vehicle handling, comfort and fuel
economy and will increase tyre wear.
Picture no: 17213t.tif
9
Warning
If the pressure is too low, this can result
in considerable tyre warm-up and
internal damage, leading to tread sepa-
ration and even to tyre blow-out at high
speeds.
Back to overview

170 Driving and operation
Picture no: 17214t.tif
Tyre condition, wheel condition
Drive over edges slowly and at a right
angle if possible. Driving over sharp edges
can lead to hidden tyre damage and wheel
damage. Do not wedge tyres against the
kerb.
Regularly check tyres for damage. Seek the
assistance of a workshop in the event of
damage or unusual wear.
Picture no: 17216t.tif
Tread depth
Check tread depth regularly.
For reasons of safety, tyres should be
replaced when their tread depth has worn
down to 2 to 3 mm (winter tyres: 4 mm).
The legally permissible minimum tread
depth (1.6 mm) has been reached when
the tread has worn down as far as one of
the wear indicators (TWI
1)). A number of
wear indicators are spaced at equal
intervals around the tyre within the tread.
Their position is indicated by markings on
the tyre sidewall.
Picture no: 17215t.tif
If wear in the front is greater than that in
the rear, move the rear wheels to the front
axle and vice versa.
Correct tyre pressure.
On vehicles fitted with a deflation
detection system 3, initialise the system
3 164.
General information
z The danger of aquaplaning is greater if
the tyres are worn.
z Tyres age, even if they are not used or
used infrequently. We recommend tyre
replacement every six years at the latest.
z Never fit used tyres the previous history
and use of which you do not know.
1)TWI
= Tread
Wear
Indicator.
Back to overview