2009 OPEL CORSA Owners Manual

211
Self-help, vehicle care
Picture no: 18590s.tifPicture no: 18261s.tif
Fuse box in luggage compartment
The fuse box is located behind the cover in
the left luggage compartment trim.
Remove cover from fuse box.
Picture no: 18319s.tif
No. Circuit
1 –
2 Instruments, information display
3 Radio
4 Ignition switch
5 Windscreen washer system
6 Unlocking the luggage
compartment
7 Central locking system
8 –
9 Courtesy lamp
10 Electric power steering
11 Light switch, brake lamp
12 ABS, brake lamp
13 Heated steering wheel
14 Park pilot, rain sensor, interior
mirror
No. Circuit
1 Adaptive Forward Lighting
2 –
3 Seat heater (left)
4 Seat heater (right)
5 –
6 –
7 –
8 Flex-Fix system, towing equipment
No. Circuit
9 –
10 –
11 –
12 –
13 –
14 –
15 Flex-Fix system, towing equipment
16 –
17 Sun roof
Back to overview

212 Self-help, vehicle careBulb replacement Switch off the ignition and switch off the
relevant switch or close the doors.
Only hold a new bulb at the base! Do not
touch the bulb glass with your bare hands.
Replace the bulb, checking that the data
on the base matches that of the defective
bulb.
Picture no: 18422s.tif
To replace the bulb on the right-hand side,
remove the air hose from the air filter.
To replace the bulb on the left-hand side,
remove fuse box cover3209, and also
remove windscreen washer system
reservoir filler neck from above. Washing
fluid may escape if the reservoir is full to
the top.
Picture no: 18129s.tif
Halogen headlamp system Headlamp system has separate bulbs for
dipped beam 1 (outer bulbs) and main
beam 2 (inner bulbs).
Back to overview

213
Self-help, vehicle care
Picture no: 18134s.tif
Dipped beam
1. Open bonnet and engage support.
2. Disengage wire clip and remove cover.
Picture no: 18135s.tif
3. Press base to the side and remove from reflector.
Picture no: 17270t.tif
4. Detach plug connector from bulb.
5. Insert new bulb in reflector so that the
locating tab of the bulb holder aligns
with the reflector recess. Attach the
bulb holder so that the locating tab
points upwards.
6. Engage bulb.
7. Attach connector to bulb.
8. Put on cover and engage wire clip.
Back to overview

214 Self-help, vehicle care
Picture no: 18130s.tif
Main beam
1. Open bonnet and engage support.
2. Rotate headlamp cap anticlockwise and remove.
3. Detach plug connector from bulb.
Picture no: 18132s.tif
4. Disengage spring wire clip from retaining lugs by moving it and swivelling it to the
side.
5. Remove bulb from reflector housing.
6. When fitting the new bulb, insert lugs in
the reflector recesses.
Picture no: 18133s.tif
7. Engage spring wire clip, plug connector
onto bulb.
8. Fit headlamp cap and rotate clockwise.
Back to overview

215
Self-help, vehicle care
Picture no: 18130s.tif
Parking lamps
1. Open bonnet and engage support.
2. Rotate the main beam headlamp cap anticlockwise and remove.
Picture no: 18139s.tif
3. Remove parking lamp socket from reflector.
Picture no: 18140s.tif
4. Remove bulb from socket.
5. Insert new bulb.
6. Insert socket in reflector.
7. Fit headlamp cap and rotate clockwise.
Back to overview

216 Self-help, vehicle care
Picture no: 18129s.tif
Adaptive Forward Lighting
system
3
Headlamp system has separate systems
for dipped beam 1 (outer bulbs) and main
beam 2 (inner bulbs). The cornering light is
also located behind the cover for the main
beam.
Due to the complexity of the procedure,
bulb changes should be carried out by a
workshop.
Picture no: 18134s.tif
Dipped beam
1. Open bonnet and engage support.
2. Disengage wire clip and remove cover.
Picture no: 18374s.tif
3. Press base upwards and remove from reflector.
Back to overview

217
Self-help, vehicle care
Picture no: 17270t.tif
4. Detach plug connector from bulb.
5. Insert new bulb in reflector so that the
locating tab of the bulb holder aligns
with the reflector recess. Attach the bulb
holder so that the locating tab is on the
side.
6. Engage bulb.
7. Attach connector to bulb.
8. Put on cover and engage wire clip.
Picture no: 18130s.tif
Main beam
1. Open bonnet and engage support.
2. Rotate the main beam headlamp cap
anticlockwise and remove.
Picture no: 18379s.tif
3. Detach plug connector from bulb.
Back to overview

218 Self-help, vehicle care
Picture no: 18380s.tif
4. Disengage spring wire clip from retaining lugs by moving it and swivelling it to the
side.
5. Remove bulb from reflector housing.
6. When fitting the new bulb, insert lugs in the reflector recesses.
7. Engage spring wire clip, plug connector onto bulb.
8. Fit headlamp cap and rotate clockwise.
Picture no: 18130s.tif
Cornering light
1. Open bonnet and engage support.
2. Rotate the main beam headlamp cap
anticlockwise and remove.
Picture no: 18376s.tif
3. Detach plug connector from bulb.
Back to overview