2009 OPEL CORSA Owners Manual

107
Instruments, controls
Picture no: 18328s.tif
Keep the sensor field of the rain sensor free
from dust, dirt and ice.
Picture no: 18174s.tif
Windscreen washer system
Pull stalk towards steering wheel. Screen
wash is squirted onto the screen and the
wipers move back and forth a few times.
Picture no: 18175s.tif
Rear window wiper 3 and rear window
washer system 3
To switch on, push st alk forwards. The rear
window wiper swipes in timed interval
mode. Switch off by pushing stalk forwards
again.
If the stalk is held forwards, washer fluid is
sprayed on the rear window.
Automatic rear window wiper 3
The rear window wiper switches itself on
automatically when the windscreen wiper
is switched on and reverse gear is selected.
This function can be activated or
deactivated depending on the key that is
used, see "Personalised Key", P2 339,
3 41.
Back to overview

108 LightingLighting
Picture no: 18197s.tif
Exterior lightsTurn light switch:
In positions 8 and 9, the tail lamps and
number plate lamps are also on.
Control indicator 8388.
If the ignition is switched off when main
beam or dipped beam is on, the parking
lamps come on.
The parking lamps go off when the ignition
key is removed. Versions with daytime running lights 3
:
Parking lamps are on when the ignition is
switched on and the lig ht switch is set to 7
or A 3. Dipped beam is on when the engine
is running.
The daytime running lig hts switch off when
the ignition is switched off.
Follow the regulations of the country in
which you are driving when using daytime
running lights and fog lamps 3.
Driving abroad 3117.
Exterior lights ....................................... 108
Main beam, headlamp flash .............. 109
Automatic dipped beam
activation A 3................................. 109
Turn signal lamps ................................ 109
Fog lamps > 3.................................... 110
Fog tail lamp r................................... 110
Reversing lamps................................... 110
Hazard warning lamps ....................... 111
Headlamp range adjustment ? 3..... 111
Adaptive Forward Lighting 3 (AFL) .. 112
Lead-me lighting 3............................. 113
Switching on the exterior lighting with the remote control 3......................... 113
Parking lamps ...................................... 114
Instrument illumination, Information display illumination ........................... 114
Courtesy lamp...................................... 114
Battery discharge protection .............. 116
Misted light covers............................... 116
Headlamps when driving abroad ...... 117 7
=Off
8 = Parking lamps
9 = Dipped or main beam
Back to overview

109
Lighting
Picture no: 18165s.tif
Main beam, headlamp flash Push stalk forward to switch from dipped
beam to main beam.
To switch to dipped beam, push stalk
forward again or pull towards steering
wheel.
To operate the headlamp flash, pull stalk
towards steering wheel. The main beam is
switched on for as long as the stalk is held
in this position.
Picture no: 18198s.tif
Automatic dipped beam
activation A
3
Light switch set to A: when the engine is
running, dipped beam switches on when
external light conditions are poor.
The exterior lights switch off when the
ignition is switched off.
For reasons of safety, the light switch
should always remain in the A position.
If visibility is poor (in foggy conditions, for
example) turn light switch to 9.
Picture no: 18167s.tif
Turn signal lamps Push stalk up or down to activate:
After operation, the turn signal stalk
returns to its starting position.
If the stalk is moved past the resistance
point, the turn signal lamp remains on.
When the steering wheel moves back
toward the straight-ahead position, the
turn signal lamp is automatically
deactivated.
Move the stalk to the resistance point and
hold for the turn signals to flash longer.
Switch the turn signal off manually by
moving the stalk slightly. Lever upwards = Right turn signal
Lever downwards = Left turn signal
Back to overview

110 LightingShort turn signal 3
Push stalk until you feel resistance and
release. The turn signal flashes three times,
e.g. for changing lanes. This function can
be activated or deactivated depending on
the key that is used, see "personalised key",
P3 339, 341.
Acoustic turn signal 3
The volume of the acoustic turn signal can
be adjusted. This function can be
programmed depending on the key used,
see "Personalised key", P7 339, 341.
Picture no: 18199s.tif
Fog lamps
> 3

The fog lamps can only be switched on
when both the ignition and lights are on.
Operated with the > button.
Fog tail lamp
r
The fog tail lamp can only be switched on
both the ignition and dipped beam/parking
lamps are on.
Operated with the r button.
The vehicle fog tail lamp are deactivated
when towing.
Reversing lamps The reversing lamps come on when the
ignition is on and reverse gear is engaged.
Back to overview

111
Lighting
Picture no: 18169s.tif
Hazard warning lamps Operated with the ¨ button.
To aid location of the pushbutton, the red
surface is illuminated when the ignition
switched on. When the button is pressed,
its control indicator flashes in time with the
hazard warning lamps.
The hazard warning flashers activate
automatically if the airbags deploy.
Picture no: 18200s.tif
Headlamp range adjustment
? 3

Adjust headlamp range to suit the vehicle
load to avoid dazzling oncoming traffic.
Push button
I or
J step-by-step until the
required setting is displayed on the
kilometre display.
The display shows for 4 seconds, when
dipped beam is switched on or every time
the beam range is changed, together with
the symbol ?.
Picture no: 18419s.tif
0 = Front seats occupied
1 = All seats occupied
2 = All seats occupied and luggage
compartment load
3 = Driver’s seat occupied and luggage compartment load
Back to overview

112 Lighting
Picture no: 17793j.tif
Adaptive Forward Lighting
3
(AFL) ensures better illumination of
zbends (curve lighting),
z crossings and narrow bends
(cornering light).
Curve lighting (1)
The light beam pivots based on
steering wheel position and speed
(from approx. 10 km/h).
The headlamps shine at an angle of up to
15 to the right or left of the direction of
travel.
Picture no:
Cornering light (2)
An additional light is switched on
depending on the stee ring wheel position
(from rotation of approx. 90), turn signal
position and speed (up to approx. 40 km/h).
The light is thrown approx. 90 to the
left or right of the car, to a distance of
approx. 30 metres.
Reversing function
If the lights are on, reverse gear is
engaged, and the turn signal is activated,
the cornering light on the appropriate side
is switched on. The cornering light stays on
for 15 seconds once the turn signal has
been switched off.
Picture no: 18249s.tif
Control indicator fo r adaptive driving
lamps
B
Illuminated: Fault in system. The system is
not ready for operation.
Contact a workshop for assistance.
If control indicator
B flashes for
approx. 4 seconds after the ignition is
switched on, this is a reminder that the
headlamps have been set to symmetrical
dipped beam; see "Headlamps when
driving abroad" 3117.
Back to overview

113
Lighting
Picture no: 18302s.tif
Lead-me lighting
3
The dipped beam remains switched on for
approx. 30 seconds once you have left the
vehicle and closed the driver’s door.
To activate
1. Switch off ignition.
2. Remove ignition key.
3. Open driver’s door.
4. Pull turn signal stalk toward steering wheel.
5. Close driver’s door.
If the driver’s door is left open, the lamps
will go out after two minutes.
The light is switched off immediately by
inserting the key into the ignition or pulling
the turn signal stalk towards the steering
wheel again.
Picture no: 18420s.tif
Switching on the exterior lighting
with the remote control
3
The lead-me-to-the-car light function
switches the dipped beam on for
approx. 30 seconds.
Program function
This function can be activated and
deactivated depending on the key used,
see "Personalised key", P1 339 341. To activate
Press button
q on the remote control twice
when the vehicle is locked.
Country-specific application 3: To switch
on the Lead-me-to-the-car light function,
press button q on the remote control once
the vehicle is locked.
Switching on the ignition or pressing
button p on the remote control will
deactivate the Lead-me-to-the-car light
function early.
Back to overview

114 Lighting
Picture no: 18370s.tif
Parking lamps The front parking lamp and tail lamp of
one side of the vehicle can be activated
when parking:
1. Set light switch to 7 or A 3,
2. Ignition off,
3. Move turn signal stalk all the way up (right parking lamp) or down (left
parking lamp).
Confirmed by a signal and the
corresponding turn signal control indicator.
To switch it off, swit ch on the ignition or
move the turn signal stalk in the opposite
direction.
Picture no: 18201s.tif
Instrument illumination
,
Information display illumination

Lights come on when ignition is switched
on.
Adjustable brightness when exterior
lighting is switched on:
Hold down the button until the required
brightness is achieved.
Display mode 33100.
Courtesy lamp Automatic interior light
Comes on automatically when the vehicle is
unlocked with the remote control, when a
door is opened or when the key is removed
from the ignition switch after the ignition is
switched off.
Goes off automatically after a delay when
the doors are closed or immediately when
the ignition is switched on or the doors are
locked.
Brighter = Push button +
Darker = Push button -
Back to overview