2009 CHERY TIGGO immobilizer

Downloaded from www.Manualslib.com manuals search engine 8.CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• Refer to DTC Confirmation Procedure.
Is DTC P0444 still present?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03
03–393Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Diagnostic Procedure
1.CHECK INTAKE AIR LEAK
• Start engine and let it idle.
• Listen for an intake air leak after the mass air flow sensor.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Discover air leak location and repair.
2.CHECK THE ELECTRIC THROTTLE CONTROL ACTUATOR
• Check the electronic throttle open degree.
• Check the electronic throttle clearance.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Clean or replace as necessary.
3.CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• Refer to DTC Confirmation Procedure.
Is DTC P0506 still present?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03
03–395Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Diagnostic Procedure
1.CHECK DTC
• Perform DTC confirmation procedure.
Is DTC P0604, P0605 or P0606 present?
Ye s>>Go to the next step.
No
>>The DTC condition is intermittent (See Diagnostic Help in Section 03 Electronic Engine Controls).
2.CHECK ECM POWER SUPPLY AND GROUND
• Check if the ECM supply voltage circuit, ground circuit open, high resistance or short circuits existing.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace circuit for open or short in harness and connectors.
3.CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• Refer to DTC Confirmation Procedure.
Is the check result normal?
Ye s>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
No
>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
DIAGNOSIS & TESTING
03
03–397Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Diagnostic Procedure
1.CHECK DTC
• Perform DTC confirmation procedure.
Is DTC P0602 present?
Ye s>>Go to the next step.
No
>>The DTC condition is intermittent (See Diagnostic Help in Section 03 Electronic Engine Controls).
2.CHECK THE ECM POWER SUPPLY AND GROUND
• Check if the ECM supply voltage circuit, ground circuit open, high resistance or short circuits existing.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace circuit for an open or short in harness and connectors.
3.MATCH ECM
With the scan tool X-431, match ECM before replace it (See ECM Removal & Installation in Section 03 Electronic
Engine Controls), and view the DTC with the X-431.
Is DTC P0602 setting again?
Ye s>>Go to the next step.
Refer to Technical Bulletin that issued.
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
4.CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• See DTC Confirmation Procedure.
Is DTC P0602 still present?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03
03–399Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4.CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• Refer to DTC Confirmation Procedure.
Is DTC P0645 still present?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03–404Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 9.CHECK TPS
• Connect all harness connectors disconnected.
• Turn ignition switch on.
• Check voltage between ECM terminals 54 (TPS1) and ground, terminal 38 (TPS2) and ground under the follow-
ing conditions:
TPS
TERMINAL NO. ITEM
CONDITION DATA (DC
VOLTAGE)
5 Electronic
throttlecontrol
actuator (TPS2)
Ignition
switch:
ON •
Engine
stopped
•
Accelerator
pedal:
Fully
released 4.24 V
• Engine
stopped
•
Accelerator
pedal:
Fully
depressed 0.72 V
6 Electronic
throttlecontrol
actuator (TPS1) •
Engine
stopped
•
Accelerator
pedal:
Fully
released 0.74 V
• Engine
stopped
•
Accelerator
pedal:
Fully
depressed 4.62 V
Is the check result normal?
Ye s>>Go to the next step.
No
>>Replace electronic throttle control actuator, and perform throttle valve position learning.
10.CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• See DTC Confirmation Procedure.
Is DTC P1545 still present?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03–412Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4.DETECT MALFUNCTIONING PART
• Check the following:
Harness connectors E-102, C-102
Harness open and short between APP sensor 1 and ECM
Is the check result normal?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>Repair or replace malfunctioning part.
5.CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT
• Check APP sensor supply voltage between sensor
terminal 3 and ground in the sensor electrical con-
nector C-009.
• Approximately 5 V should exist.
Is the check result normal?
Ye s>>Go to step 7.
No
>>Go to the next step.
6.DETECT MALFUNCTIONING PART
• Check the following:
Harness connectors E-102, C-102
Harness open and short between APP sensor 2 and ECM
Is the check result normal?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>Repair or replace malfunctioning part.
7.CHECK TPS POWER SUPPLY CIRCUIT
• Check harness for short to power and short to ground, between following terminals.
Check TPS Power Supply
ECM TERMINAL TPS TERMINAL
32 3
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair circuit for a short to ground or short to power in harness or connectors.
DIAGNOSIS & TESTING
LTSMD030066
03
03–417Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 10.CHECK APP SENSOR CIRCUIT FOR AN OPEN OR SHORT
• Check harness continuity between APP sensor 1 terminal 4 and ECM terminal 16, APP sensor 2 terminal 1 and
ECM terminal 40.
• Continuity should exist.
• Also check harness for short to power and short to ground.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair circuit for an open or short to power or short to ground in harness or connectors.
11 .CHECK APP SENSOR
• Connect all harness connectors disconnected.
• Turn ignition switch on.
• Check voltage between ECM terminals 16 (APP sensor 1 signal), 40 (APP sensor 2 signal) and ground under
the following conditions:
TERMINAL NO. ITEM CONDITION DATA (DC
VOLTAGE)
16 Accelerator Pedal
Position sensor
Turn ignition switchon •
Engine stopped
• Accelerator pedal:
Fully released 0.72 - 0.74 V
• Engine stopped
• Accelerator pedal:
Fully depressed 3.95 V
40 Accelerator Pedal
Position sensor •
Engine stopped
• Accelerator pedal:
Fully released 0.36 - 0.37 V
• Engine stopped
• Accelerator pedal:
Fully depressed 1.97 V
Is the check result normal?
Ye s>>Go to the next step.
No
>>Replace accelerator pedal assembly.
Perform Accelerator pedal position self-learning.
12.CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• Refer to DTC Confirmation Procedure.
Is DTC P2138 still present?
Ye s>>Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03
03–419Chery Automobile Co., Ltd.