2008 RENAULT SCENIC navigation system

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 22V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF029
PRESENT
OR
STOREDREADING NAVIGATION DVD
1.DEF : Disc cannot be read
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the navigation
system started with a navigation DVD in good condition.
Check that the DVD is inserted the right way up.
Check that the DVD in the navigation computer is not an audio CD or other type but a navigation DVD designed
for this navigation system.
Wipe the DVD from the centre out with a soft, clean cloth.
Replace the navigation DVD if it is scratched.
If the fault is still present after the DVD has been changed, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF029ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 23V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF030
PRESENT
OR
STOREDGPS AERIAL CIRCUIT
CO : Open circuit
NOTESConditions for applying the fault finding procedure to the stored fault:
Apply this fault finding procedure if the fault reappears as present or stored after it has
been cleared and the ignition has been switched off and on again.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the GPS aerial 2-track connectors (component code 886) and of the
navigation computer (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 46CB,
●connection code TB15,
between components 662 and 886.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the connections are correct, replace the GPS aerial.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF030ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of commands
86C
86C - 40V5 MR-372-J84-86C050$832.mif
ITS
Program no.: 0020
Vdiag No.: 04
AC006
SCREEN TEST: COLOUR BARS
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Apply this procedure if one or more colour bars is missing on the display when this command is run.
Check the condition and connection of the display connector (component code 1127) and of the navigation
computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check for + 12 V on connection BCP3 of the component 1127 connector.
Check that the earth on connection 34GU of the component 1127 connector is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code TB31,
●connection code 34DD,
●connection code 34DC,
●connection code 34DB,
●connection code 34GU,
between components 1127 and 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the checks reveal no faults, but the colours displayed by component 1127 are incorrect, replace
component 1127.
AFTER REPAIRCarry out another fault finding check on the system.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of commands
86C
86C - 41V5 MR-372-J84-86C050$832.mif
ITS
Program no.: 0020
Vdiag No.: 04
AC007
SCREEN TEST: GRADATION OF GREY
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Apply this procedure if the shade of grey shown on the display when the command is activated is incorrect.
Check the condition and connection of the display connector (component code 1127) and of the navigation
computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check that the earth on connection 34GU of the component 1127 connector is perfect.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check that the earth on the MAN connection of component 1127 is perfect.
Check for + 12 V on connection BCP3 of the component 1127 connector.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code TB30,
●connection code 34HA,
●connection code 34GZ,
between components 1127 and 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the checks reveal no faults, but the gradation of grey displayed by the display is not correct, replace
component 1127.
AFTER REPAIRCarry out another fault finding check on the system.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of commands
86C
86C - 42V5 MR-372-J84-86C050$832.mif
ITS
Program no.: 0020
Vdiag No.: 04
AC009
MICROPHONE TEST
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Apply this procedure if the Faulty connection message appears when these commands are activated.
Check the condition and connection of the microphone connector (component code 789) and of the navigation
computer 40-track connector (component code 662) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 107J,
●connection code 107G,
●connection code 107F,
between components 789 and 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the checks reveal no faults but the microphone does not work, replace component 789.
AFTER REPAIRCarry out another fault finding check on the system.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Customer complaints
86C
86C - 44V5 MR-372-J84-86C050$884.mif
ITS
Program no.: 0020
Vdiag No.: 04
NOTESOnly refer to these customer complaints after performing a full check with the
diagnostic tool.
AFTER UPDATING THE NAVIGATION DVD, THE SYSTEM NO LONGER WORKS ALP 12
IMPOSSIBLE TO USE TELEPHONE WITH BLUETOOTH ALP 13
NOT POSSIBLE TO MAKE A CALL FROM THE NUMBERS STORED IN THE LIST OF
RECEIVED CALLSALP 14
THE CALL IS NOT TRANSFERRED TO THE NAVIGATION AND COMMUNICATION
SYSTEM IF A NUMBER IS DIALLED ON THE TELEPHONEALP 15
COMMUNICATIONS ARE SUBJECT TO INTERFERENCE IN BLUETOOTH ALP 16
THE PERSON CALLING USING THE COMMUNICATION SYSTEM CANNOT HEAR
ME VERY WELL OR CANNOT HEAR ME AT ALL (WITH BLUETOOTH)ALP 17
VOICE RECOGNITION IS NOT WORKING ALP 18
THE DISPLAY ON THE SCREEN STAYS FROZEN ALP 19
THE SCREEN DISPLAYS CONNECT A DIAGNOSTIC TOOL ALP 20
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-46V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 2 the screen stays black
NOTESOnly check the customer complaint after performing a full check with the
diagnostic tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
Check that the display has not been deactivated.
Press the LIGHT button on the central control for 2 seconds to reactivate the display.
To check the supply to the display, switch on
the ignition, switch on the navigation system
and eject the navigation DVD.
Has the DVD been removed?
YES
Check for + 12 V on connection BCP3 and an earth
on connection MAN of the display (component
code 1127).
Are these tests correct?
YES
Check the insulation, continuity and the absence
of interference resistance of connection 34HU
between components 1127 and 1272.
–If the connection is correct, replace the display.
–If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the wiring; otherwise, replace
the wiring.
NOCheck the condition of the supply fuse
(20A) (component code 260).
Has the fault disappeared?
YES NO
Check for + 12 V on
connection BCP3 and an
earth on connection MX of
the navigation computer
(component code 662).
NOCheck the insulation,
continuity and the absence
of interference resistance
of connections 34DB, 34DC
et 34DD between
components 662 and 1127.
YES Are these checks correct?
NO
If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring; otherwise, replace the wiring.
End of fault finding.
Contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP2ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-47V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 3 No voice messages
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
Check that the sound from the radio is coming through the front and rear speakers.
Otherwise, adjust the sound for all vehicle speakers. Press the SET button, select the audio; balance or fader
menus.
Check that voice guidance is activated.
Press the SET button and select the Navigation;
Guidance preference; Voice guidance menus.
Has voice guidance been activated?
YES
Ensure that the voice guidance volume has been
properly adjusted.
Press the SET button and select the Volume
and beeps, and Guidance volume menus.
Has the voice guidance volume been properly
adjusted?
YES
Has the fault disappeared?
NO
NOActivate voice guidance.
NOAdjust the voice guidance volume.
YESEnd of fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP3ITSJ84ph2V1.0