2008 RENAULT SCENIC navigation system

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-49V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 4 No traffic information messages appear on the screen
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
TMC road information is disseminated via the FM
band on the radio. The TMC pictogram should be
green in order for the traffic information to be
received.
What colour is the TMC pictogram?
Green
The system is operating correctly, but there is no
traffic information to be transmitted.
Check that the traffic information display has been
activated.
Press the INFO button and select the TMC traffic
information; Traffic information adjustment;
Card display menus.
Has the display been activated?
YES
Check that the traffic information settings are
correct.
Press the INFO button and select the TMC traffic
information; Traffic information adjustment;
Type of information to be displayed; Traffic
information service menus.
Make any necessary adjustments.
GreyNo traffic information is being received.
NOActivate the traffic information display.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP4ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-50V5 MR-372-J84-86C050$936.mif
If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring; otherwise, replace the wiring.
ITS
Program No.: 0020
Vdiag No.: 04
ALP 5 Poor satellite reception
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Ensure there are no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
What colour is the GPS pictogram?
Green
The system operates normally.
Yellow
or
GreyPositioning is imprecise (yellow) or
impossible (grey) in the following areas:
forests, tunnels, valleys, under bridges
and in stormy weather.
Carry out a system test in an open area.
Check the condition and cleanliness of the
GPS aerial.
Check the insulation, continuity and
the absence of interference resistance
of connections 46CB and TB15 between
components 662 and 886.
NO Did it pass the tests?
YES
If the fault is still present, replace the GPS
aerial.
If the satellite reception is poor, contact
the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP5ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-51V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 6The radio does not switch on automatically or switches off after
20 minutes
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
The navigation system does not receive the multimedia wake-up signal when the + after ignition feed is
switched on.
Check the condition of the CD changer fuses (component code 1272).
Has the fault disappeared?
NO YES
On pressing the CD changer on/off button, check for
the multimedia wake-up signal on connection 34HU
on the radio's blue connector (component
code 261).
Is the check result correct?
NO
Check the insulation, continuity and the absence
of interference resistance of connection 34HU
between components 1272, 261, 1657, 1127
and 662.
If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring; otherwise, replace the wiring.
Has the fault disappeared?
NO YES
End of fault finding.
End of fault finding.
YESCheck for + 12 V (+ battery feed) on
connection BCP3 of the component 261
black connector.
Is the check result correct?
NO YES
Check the insulation, continuity and the
absence of interference resistance of
connection BCP3 between components 261
and 260.
If any connection is faulty and if there is a repair
method (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring;
otherwise, replace the wiring.
Has the fault disappeared?
YES NO
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP6ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-53V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 7 Clock not displayed or incorrect
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Check that the time display is activated and the time
zones and settings are correct.
Press the SET button, select the clock; clock
display; time adjustment; summer time;
time zone.
Are these adjustments correct?
YES
Place the vehicle outside in an open area and check
that the satellite reception is correct.
Is the GPS pictogram green?
YES
Wait a few minutes in a location with good satellite
reception.
If the time is still wrong, contact the Techline.
NOSet the display and time.
Explain to the customer how to make
these adjustments.
NOSee fault finding chart: ALP 5 Poor
satellite reception.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP7ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-54V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 8 The volume does not change with a change in vehicle speed
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
Check that volume according to speed function has
been activated.
Press the SET button and select the volume
correction menu.
Is the volume according to speed function
active?
YES
Carry out fault finding on the ABS/ESP (see 38C,
Anti-lock braking system).
Check the condition and connection of the receiver 32-track connector (component code 261) and of the navigation
computer 32-track connector (component code 662). If the connectors are faulty and if there is a repair method
(see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair), repair
the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the connection 47F between
components 261 and 662. If the connection is faulty and if there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
NOActivate this function.
Carry out a road test and check that
the volume varies as the vehicle speed
varies.
Does the volume vary?
NO YES
End of fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP8ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-60V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 12 After updating the navigation DVD, the system no longer works
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the navigation computer software version is compatible with the navigation DVD update.
If the navigation DVD is not compatible with the navigation computer software, suggest that the customer buys
a navigation DVD in a version compatible with the vehicle's navigation system.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP12ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-61V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 13 Impossible to use the telephone with Bluetooth
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the system properly.
Check that fault DF009 Computer is not present or stored.
Note:
List of telephones researched and approved by Renault in March 2005: Nokia 6820, Nokia 6230, Siemens S65,
Motorola V500, Motorola V600.
For information on the latest list of telephones approved by Renault and the various operations to perform on these
telephones, see Technical Note 6024A Special features of mobile phones for the navigation
and communication system.
Check that Bluetooth mode is activated in the navigation and communication system.
Press the SET button and select the telephone; Bluetooth option; Bluetooth connection menus.
Has the telephone been researched by Renault?
YES
Check that the telephone software on the telephone
is compatible with the vehicle's navigation
and communication system.
The telephone software compatible with
the vehicle's navigation and communication system
is greater than or equal to:
Nokia 6230 and 6820: v 03.15
Motorola V500 and V600: Triplets_G_0B.09.44R
Siemens S65: v 12
Is the telephone software compatible with
the vehicle's navigation and communication
system?
YES
Command to find out the telephone's software
(see Technical Note 6024 Special features on mobile
phones used with the navigation and communication
system):
–Nokia: *#0000#
–Motorola: select configuration, telephone status then
version information
–Siemens: *#06# NOSuggest that the customer buy
a telephone approved by Renault.
NOAsk the customer to contact
the telephone vendor in order to install
a software version into the telephone
that would be compatible with
the navigation and communication
system.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP13ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-62V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 13
CONTINUED 1
Activate the telephone's Bluetooth mode
(see NT 6024A Special features of mobile
phones used with the navigation
and communication system).
Match up the navigation and communication system
and the telephone.
Was the match successful?
YES NO
Test the Bluetooth terminal on
the navigation computer.
Check that the telephone does not need to be
confirmed before it is connected to the Bluetooth
system.
If this is the case, confirm in order to connect
the telephone then inhibit this function in the
telephone (not possible on Siemens telephones).
Procedure for activating the telephone's Bluetooth
mode:
–Nokia: Select Parameters, Connectivity, Bluetooth,
Activate in the main menu.
–Motorola: Select Configuration, Connection,
Bluetooth link, Configuration, Supply, Activated in
the main menu.
–Siemens: Select Adjustments, Mode/Data, Bluetooth,
then activate Bluetooth mode.
Procedure for matching the communication system
and the telephone:
On the navigation and communication system:
–Press the SET button.
–Enter the telephone menu.
–Select the Bluetooth option line.
–Select the save a Bluetooth telephone line.
On the telephone:
–Enter the menu to find a Bluetooth accessory.
–In the list of found accessories, select My CAR.
Enter the PIN code given on the vehicle's navigation
display
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITSJ84ph2V1.0