2008 RENAULT SCENIC ignition

MULTIMEDIA
Fault finding - Introduction
86C
86C-2V5 MR-372-J84-86C050$052.mif
186C
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP + multiplex line sensor
Special tooling required
3. REMINDERS
Procedure
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
–vehicle card in reader,
–press and hold start button (longer than 5 seconds) with start-up conditions not fulfilled,
–connect the diagnostic tool and perform the required operations.
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–check that the computer warning lights on the instrument panel have gone out to confirm that the + after ignition
feed has been cut off. Vehicle: Scenic II ph2
Function concerned: Navigation, integrated
hands-free telephone, receiver, CD playerName of computer: ITS
Program No.: 0020
Vdiag No.: 04
Special tooling required
Multimeter
Elé. 1681Universal bornier
Note:
The left-hand and right-hand xenon bulb computers are powered when the dipped headlights are lit.
Fault finding can only be run after the ignition is switched on in fault finding mode (forced + after ignition feed)
and the dipped headlights are lit.
TDB_V04_PRELIITSJ84ph2V1.0
MR-372-J84-86C050$052.mif

MULTIMEDIA
Fault finding - Introduction
86C
86C-3V5 MR-372-J84-86C050$052.mif
ITS
Program No.: 0020
Vdiag No.: 04
Faults
Faults are declared present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but are not diagnosed within the current context).
The present or stored status of the faults should be considered when the diagnostic tool is switched on after
the + after ignition feed is switched on (with no system components being active).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the Notes section.
If the fault is confirmed when the instructions are applied, the fault is present. Deal with the fault.
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors on these lines (corrosion, bent pins, etc.),
–the resistance of the component detected as defective,
–the condition of the wires (melted or split insulation, wear).
Conformity check
The aim of the conformity check is to check data that does not produce a fault on the diagnostic tool because
the data is inconsistent. Therefore, this stage is used to:
–carry out fault finding on faults that do not have a fault display, and which may correspond to a customer
complaint.
–check that the system is operating correctly and that there is no risk of a fault recurring after repairs.
This section gives the fault finding procedures for statuses and parameters and the conditions for checking them.
If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult
the corresponding fault finding page.
Customer complaints - Fault finding chart
If the test with the diagnostic tool is OK but the customer complaint is still present, the fault should be processed by
Customer complaints.
A synopsis of the general procedure to follow is provided on the following page in
the form of a flow chart.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Replacement of components86C
86C-11V5 MR-372-J84-86C050$312.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Replacement of components
To remove and refit this computer (see MR 370 Mechanical, 83C, On-board telematics system, Navigation
computer: Removal - Refitting).
Procedures to be carried out before replacing the navigation computer:
1. Before replacing the computer (with the agreement of the Techline), read the faults and carry out a conformity
check to ensure that it is definitely faulty.
2. Eject the DVD.
3. Before removing the computer, clear the customer's data (telephone numbers, address book, etc.) using
command RZ003 Parameters and customer data in the diagnostic tool.
4. Remove the computer with the ignition off.
The navigation computers from the Parts Department are supplied unconfigured and in factory mode (receiver set to
162 kHz AM, and beeps for 2 minutes).
Procedures to be carried out after replacing the navigation computer:
1. Enter the unlocking code for the CARMINAT NAVIGATION AND COMMUNICATION system.
–How to obtain the unlocking code for the Carminat Navigation and Communication system
●switch on + after ignition feed,
●switch on the CARMINAT NAVIGATION and COMMUNICATION system,
●connect the Clip diagnostic tool,
●note the number of the navigation programming key written in the Identification menu,
●contact Techline with this navigation programming number to obtain the Carminat Navigation
and Communication system unlocking code,
●the unlocking code is requested 2 mins after the CARMINAT NAVIGATION and COMMUNICATION system
comes on,
●enter this code using the navigation central control.
2. Configure the computer (see Configurations and Programming).
–Enter the vehicle type via the CF001 Vehicle type command.
–For vehicles registered in the Netherlands only, complete the VP004 Netherlands Legislation configuration.
Note:
(only for vehicles registered in the Netherlands)
If the computer is replaced. Depending on the manufacturing date of the vehicle:
–BEFORE 01 JANUARY 2006, it is essential to run command VP004 Netherlands Legislation
(LC002 Netherlands)
–AFTER 01 JANUARY 2006, command VP004 Netherlands Legislation (LC002 Except Netherlands) must not
be run under any circumstances.
3. Enter the VIN code (see Dealing with commands).
–Use command VP002 Write VIN to enter the VIN. Note:
If the code is incorrect, you must wait for between 2 and 32 minutes before entering a new code.
Delete the incorrect code before entering the new one.
ITSJ84ph2V1.0
MR-372-J84-86C050$312.mif

MULTIMEDIA
Fault finding - Configurations and programming86C
86C-12V5 MR-372-J84-86C050$364.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Configurations and programming
Configurations available and operating mode
–Vehicle type (CF001):
This configuration enables the system to identify the vehicle in which it is installed.
–NETHERLANDS LEGISLATION (VP004):
List of individual configurations available on the diagnostic tool with the associated configuration reading
Procedure to follow to modify the Vehicle Type configuration.
●Establish dialogue with the computer.
●Select the menu repair mode.
●Select the Write configuration menu.
●Select the line corresponding to the configuration to be modified.
●Select the line in the drop-down menu that corresponds to the vehicle.
●Click on Confirm.
●Exit diagnostic mode (ends dialogue with the computer without switching off the tool), switch off the ignition for
5 seconds and then switch the ignition back on.
●Establish dialogue with the computer.
●In the Read configuration menu, check that the configuration has been completed.
Programming
Procedure to follow to modifiy the Country Type configuration (this programming only affects the Netherlands and is
irreversible).
●Establish dialogue with the computer.
●Select the menu repair mode.
●Select the Programming menu.
●Select the line corresponding to the configuration to be modified.
●Select the line in the drop-down menu that corresponds to the country.
●Exit diagnostic mode (ends dialogue with the computer without switching off the tool), switch off the ignition for
5 seconds and then switch the ignition back on.
●Establish dialogue with the computer.
●In the Read configuration menu, check that the configuration has been completed. IMPORTANT
Running command NETHERLANDS LEGISLATION initialises the computer according to this country's legislation.
This configuration is IRREVERSIBLE: it is not possible to clear this selection.
Note:
(only for vehicles registered in the Netherlands)
If the computer is replaced. Depending on the manufacturing date of the vehicle:
–BEFORE 01 JANUARY 2006, it is essential to run command VP004 Netherlands Legislation
(LC002 Netherlands)
–AFTER 01 JANUARY 2006, command VP004 Netherlands Legislation (LC002 Except Netherlands) must not
be run under any circumstances.
ConfigurationConfiguration
readingName of configuration Choice of configuration
CF001 LC001 Vehicle type Scenic II
VP004 LC002 Country typeExcept Netherlands
Netherlands
ITSJ84ph2V1.0
MR-372-J84-86C050$364.mif

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 14V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of faults
DF001
DF002
DF003
DF004
DF005
DF006
DF007
DF008
DF009
DF010
PRESENT
OR
STOREDCOMPUTER
1.DEF : Internal electronic fault
NOTESUse the Wiring Diagrams Technical Note, Scenic II.
STORED FAULT
Clear the fault, switch off the ignition and disconnect the 20A computer supply fuse.
–Refit the fuse and switch the ignition back on.
–Turn on the navigation system.
If the fault reappears as stored, contact Techline.
If the fault does not reappear: operate the navigation system, including the CD multi-changer, the tuner-amplifier
and the hands-free telephone integrated control (if present on the vehicle) to check that the system is operating
correctly.
Check the conformity of the + 12 V on the BCP3 connection of the navigation computer 40-track connector
(component code 662).
Check that the earth on the MX connection of the 40-track connector of component 662 is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
FAULT PRESENT
If the fault is present, contact the Techline.
AFTER REPAIRIf the computer was replaced (at the request of the Techline), reconfigure the computer
(see Configurations and programming).
Deal with any other faults.
ITS_V04_DF001 /ITS_V04_DF002/ITS_V04_DF003/ITS_V04_DF004 /ITS_V04_DF005 /
ITS_V04_DF006 /ITS_V04_DF007/ITS_V04_DF008/ITS_V04_DF009 /ITS_V04_DF010 ITSJ84ph2V1.0
MR-372-J84-86C050$468.mif

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 15V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF021
PRESENT
COMPUTER CONFIGURATION
1.DEF : Blank or incomplete configuration
NOTESNone
Configure the system (see Configuration and programming).
After configuration, switch off the ignition for 5 seconds then switch it back on again.
Check that the configurations have been correctly registered by reading configurations LC001 Vehicle Type and
LC002 Country type.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF021PITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 16V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF022
PRESENT
OR
STOREDNO RADIO MULTIPLEX SIGNAL
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the receiver
started with several actions.
Order of priority in the event of more than one fault:
If there is a combination of faults DF022 and DF027 "No audio CD changer signals",
check the multiplex network (see 88B, Multiplex).
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and the connection of the receiver 32-track connector (component code 261), of the navigation
central control connector (component code 1657) and of the navigation computer 32-track connector (component
code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in fault status (present → stored).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, wiring: Precautions for repair), repair the connector(s); otherwise, replace the wiring.
With ignition on, check for + 12 V on connection BCP3 of the 8-track connector on component 261.
Check that the earth on the MT connection of the 8-track connector on component 261 is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 107W,
●connection code 107X,
●connection code 34HU,
between components 1657 and 261.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF022ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 18V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF023
PRESENT
OR
STOREDNO DISPLAY MULTIPLEX SIGNAL
1.DEF : No communication with display
2.DEF : Display malfunction
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after it has
been cleared, the ignition turned off and on again and the navigation system started.
Use the Wiring Diagrams Technical Note, Scenic II.
1.DEF
NOTESNone
Check the condition and connection of the display connector (component code 1127) and of the navigation
computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in fault status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
With ignition on, check for + 12 V on the BCP3 connection of the component 1127 connector.
Check that the earth on the MAN connection of component 1127 is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, replace component 1127.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF023ITSJ84ph2V1.0