MULTIMEDIA
Fault finding - Introduction
86C
86C-2V5 MR-372-J84-86C050$052.mif
186C
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP + multiplex line sensor
Special tooling required
3. REMINDERS
Procedure
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
–vehicle card in reader,
–press and hold start button (longer than 5 seconds) with start-up conditions not fulfilled,
–connect the diagnostic tool and perform the required operations.
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–check that the computer warning lights on the instrument panel have gone out to confirm that the + after ignition
feed has been cut off. Vehicle: Scenic II ph2
Function concerned: Navigation, integrated
hands-free telephone, receiver, CD playerName of computer: ITS
Program No.: 0020
Vdiag No.: 04
Special tooling required
Multimeter
Elé. 1681Universal bornier
Note:
The left-hand and right-hand xenon bulb computers are powered when the dipped headlights are lit.
Fault finding can only be run after the ignition is switched on in fault finding mode (forced + after ignition feed)
and the dipped headlights are lit.
TDB_V04_PRELIITSJ84ph2V1.0
MR-372-J84-86C050$052.mif
MULTIMEDIA
Fault finding - Configurations and programming86C
86C-12V5 MR-372-J84-86C050$364.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Configurations and programming
Configurations available and operating mode
–Vehicle type (CF001):
This configuration enables the system to identify the vehicle in which it is installed.
–NETHERLANDS LEGISLATION (VP004):
List of individual configurations available on the diagnostic tool with the associated configuration reading
Procedure to follow to modify the Vehicle Type configuration.
●Establish dialogue with the computer.
●Select the menu repair mode.
●Select the Write configuration menu.
●Select the line corresponding to the configuration to be modified.
●Select the line in the drop-down menu that corresponds to the vehicle.
●Click on Confirm.
●Exit diagnostic mode (ends dialogue with the computer without switching off the tool), switch off the ignition for
5 seconds and then switch the ignition back on.
●Establish dialogue with the computer.
●In the Read configuration menu, check that the configuration has been completed.
Programming
Procedure to follow to modifiy the Country Type configuration (this programming only affects the Netherlands and is
irreversible).
●Establish dialogue with the computer.
●Select the menu repair mode.
●Select the Programming menu.
●Select the line corresponding to the configuration to be modified.
●Select the line in the drop-down menu that corresponds to the country.
●Exit diagnostic mode (ends dialogue with the computer without switching off the tool), switch off the ignition for
5 seconds and then switch the ignition back on.
●Establish dialogue with the computer.
●In the Read configuration menu, check that the configuration has been completed. IMPORTANT
Running command NETHERLANDS LEGISLATION initialises the computer according to this country's legislation.
This configuration is IRREVERSIBLE: it is not possible to clear this selection.
Note:
(only for vehicles registered in the Netherlands)
If the computer is replaced. Depending on the manufacturing date of the vehicle:
–BEFORE 01 JANUARY 2006, it is essential to run command VP004 Netherlands Legislation
(LC002 Netherlands)
–AFTER 01 JANUARY 2006, command VP004 Netherlands Legislation (LC002 Except Netherlands) must not
be run under any circumstances.
ConfigurationConfiguration
readingName of configuration Choice of configuration
CF001 LC001 Vehicle type Scenic II
VP004 LC002 Country typeExcept Netherlands
Netherlands
ITSJ84ph2V1.0
MR-372-J84-86C050$364.mif
