2008 RENAULT SCENIC fuse diagram

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 14V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of faults
DF001
DF002
DF003
DF004
DF005
DF006
DF007
DF008
DF009
DF010
PRESENT
OR
STOREDCOMPUTER
1.DEF : Internal electronic fault
NOTESUse the Wiring Diagrams Technical Note, Scenic II.
STORED FAULT
Clear the fault, switch off the ignition and disconnect the 20A computer supply fuse.
–Refit the fuse and switch the ignition back on.
–Turn on the navigation system.
If the fault reappears as stored, contact Techline.
If the fault does not reappear: operate the navigation system, including the CD multi-changer, the tuner-amplifier
and the hands-free telephone integrated control (if present on the vehicle) to check that the system is operating
correctly.
Check the conformity of the + 12 V on the BCP3 connection of the navigation computer 40-track connector
(component code 662).
Check that the earth on the MX connection of the 40-track connector of component 662 is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
FAULT PRESENT
If the fault is present, contact the Techline.
AFTER REPAIRIf the computer was replaced (at the request of the Techline), reconfigure the computer
(see Configurations and programming).
Deal with any other faults.
ITS_V04_DF001 /ITS_V04_DF002/ITS_V04_DF003/ITS_V04_DF004 /ITS_V04_DF005 /
ITS_V04_DF006 /ITS_V04_DF007/ITS_V04_DF008/ITS_V04_DF009 /ITS_V04_DF010 ITSJ84ph2V1.0
MR-372-J84-86C050$468.mif

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 21V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF027
PRESENT
OR
STOREDNO AUDIO CD CHANGER SIGNALS
1.DEF : No communication with the CD changer keypad
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the audio
system started after using the CD multi-changer several times.
Order of priority in the event of more than one fault:
Deal with fault DF022 No radio multiplex signal first.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 15A fuse (component code 260) and the 7.5A fuse (component code 1337).
Check the condition and connection of the CD changer (component code 1272) and of the receiver C2 (green)
connector (component code 261) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
With ignition on, check for + 12 V on connections SP2, AP43 and BCP3 of the component 1272 connector.
Check that the earth on the MAN connection on the component 1272 connector is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34HT,
●connection code 34HR,
●connection code TB29,
●connection code 34HS,
between components 1272 and 261.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF027ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 29V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of statuses
ET003
+ 12 V SIDE LIGHTS FEED
NOTESVisually check that the side lights are working. Carry out fault finding on the steering
column switches and the side lights.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 7.5 A fuse in the engine compartment connection unit (component code 1337).
Check the condition and connection of the navigation central control connectors (component code 1657) and of
the CD changer (component code 1272) (broken, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the LPG connection between
components 1337, 1272 and 1657.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET003ITSJ84ph2V1.0
MR-372-J84-86C050$624.mif

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-45V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Fault finding charts
ALP 1 No dialogue with the computer
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the battery connections.
Check the condition of the fuses.
Check the battery voltage.
Try the diagnostic tool on another vehicle.
Check:
–the connection between the diagnostic tool and the diagnostic sensor (wiring in good condition),
–the connection between the diagnostic sensor and the diagnostic socket (wiring in good condition).
Check for + 12 V on the 34HU connection of the navigation computer (component code 662).
Check for + 12 V battery feed on connection BP32, for + 12 V after ignition feed on connection AP43 and for
an earth on the NAM connection and on the MAM connection of the diagnostic socket (component code 225).
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check for + 12 V battery feed on connection BCP3 and an earth on connection MX of component 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Disconnect the 32-track connector of component 662 and the connector of component 1657 to check
the insulation, continuity and absence of interference resistance of the following connections:
●connection code 34GA,
●connection code 34DZ,
between components 662 and 1657;
●connection code 107X,
●connection code 107W,
between components 1657 and 225;
●connection code BCP3,
between components 662 and 260;
●connection code MX,
between component 662 and earth MX.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP1ITSJ84ph2V1.0
MR-372-J84-86C050$936.mif

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-46V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 2 the screen stays black
NOTESOnly check the customer complaint after performing a full check with the
diagnostic tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
Check that the display has not been deactivated.
Press the LIGHT button on the central control for 2 seconds to reactivate the display.
To check the supply to the display, switch on
the ignition, switch on the navigation system
and eject the navigation DVD.
Has the DVD been removed?
YES
Check for + 12 V on connection BCP3 and an earth
on connection MAN of the display (component
code 1127).
Are these tests correct?
YES
Check the insulation, continuity and the absence
of interference resistance of connection 34HU
between components 1127 and 1272.
–If the connection is correct, replace the display.
–If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the wiring; otherwise, replace
the wiring.
NOCheck the condition of the supply fuse
(20A) (component code 260).
Has the fault disappeared?
YES NO
Check for + 12 V on
connection BCP3 and an
earth on connection MX of
the navigation computer
(component code 662).
NOCheck the insulation,
continuity and the absence
of interference resistance
of connections 34DB, 34DC
et 34DD between
components 662 and 1127.
YES Are these checks correct?
NO
If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring; otherwise, replace the wiring.
End of fault finding.
Contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP2ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-51V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 6The radio does not switch on automatically or switches off after
20 minutes
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
The navigation system does not receive the multimedia wake-up signal when the + after ignition feed is
switched on.
Check the condition of the CD changer fuses (component code 1272).
Has the fault disappeared?
NO YES
On pressing the CD changer on/off button, check for
the multimedia wake-up signal on connection 34HU
on the radio's blue connector (component
code 261).
Is the check result correct?
NO
Check the insulation, continuity and the absence
of interference resistance of connection 34HU
between components 1272, 261, 1657, 1127
and 662.
If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring; otherwise, replace the wiring.
Has the fault disappeared?
NO YES
End of fault finding.
End of fault finding.
YESCheck for + 12 V (+ battery feed) on
connection BCP3 of the component 261
black connector.
Is the check result correct?
NO YES
Check the insulation, continuity and the
absence of interference resistance of
connection BCP3 between components 261
and 260.
If any connection is faulty and if there is a repair
method (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring;
otherwise, replace the wiring.
Has the fault disappeared?
YES NO
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP6ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-57V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 10 The CD changer does not work
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the system properly.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 15 A fuses (+ accessories
feed) on component 260 and 7.5 A (+ after ignition
feed) on component 1337.
Are the fuses in good condition?
YES
Check the condition and connection of the CD multi-changer connector (component code 1272).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Has the fault disappeared?
NO YES
Disconnect the connector from component 1272,
check for + battery feed on connection BCP3, for
+ accessories feed on connection SP2 and for
+ after ignition feed on connection AP43 of
the component 1272 connector.
Also check that the earth on connection MAN is
perfect.
Did it pass the tests?
NO YES
NOReplace the fuses.
End of fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP10ITSJ84ph2V1.0