2008 RENAULT SCENIC wiring diagram

MULTIMEDIA
Fault finding - Introduction
86C
86C-2V5 MR-372-J84-86C050$052.mif
186C
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP + multiplex line sensor
Special tooling required
3. REMINDERS
Procedure
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
–vehicle card in reader,
–press and hold start button (longer than 5 seconds) with start-up conditions not fulfilled,
–connect the diagnostic tool and perform the required operations.
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–check that the computer warning lights on the instrument panel have gone out to confirm that the + after ignition
feed has been cut off. Vehicle: Scenic II ph2
Function concerned: Navigation, integrated
hands-free telephone, receiver, CD playerName of computer: ITS
Program No.: 0020
Vdiag No.: 04
Special tooling required
Multimeter
Elé. 1681Universal bornier
Note:
The left-hand and right-hand xenon bulb computers are powered when the dipped headlights are lit.
Fault finding can only be run after the ignition is switched on in fault finding mode (forced + after ignition feed)
and the dipped headlights are lit.
TDB_V04_PRELIITSJ84ph2V1.0
MR-372-J84-86C050$052.mif

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 14V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of faults
DF001
DF002
DF003
DF004
DF005
DF006
DF007
DF008
DF009
DF010
PRESENT
OR
STOREDCOMPUTER
1.DEF : Internal electronic fault
NOTESUse the Wiring Diagrams Technical Note, Scenic II.
STORED FAULT
Clear the fault, switch off the ignition and disconnect the 20A computer supply fuse.
–Refit the fuse and switch the ignition back on.
–Turn on the navigation system.
If the fault reappears as stored, contact Techline.
If the fault does not reappear: operate the navigation system, including the CD multi-changer, the tuner-amplifier
and the hands-free telephone integrated control (if present on the vehicle) to check that the system is operating
correctly.
Check the conformity of the + 12 V on the BCP3 connection of the navigation computer 40-track connector
(component code 662).
Check that the earth on the MX connection of the 40-track connector of component 662 is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
FAULT PRESENT
If the fault is present, contact the Techline.
AFTER REPAIRIf the computer was replaced (at the request of the Techline), reconfigure the computer
(see Configurations and programming).
Deal with any other faults.
ITS_V04_DF001 /ITS_V04_DF002/ITS_V04_DF003/ITS_V04_DF004 /ITS_V04_DF005 /
ITS_V04_DF006 /ITS_V04_DF007/ITS_V04_DF008/ITS_V04_DF009 /ITS_V04_DF010 ITSJ84ph2V1.0
MR-372-J84-86C050$468.mif

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 16V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF022
PRESENT
OR
STOREDNO RADIO MULTIPLEX SIGNAL
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the receiver
started with several actions.
Order of priority in the event of more than one fault:
If there is a combination of faults DF022 and DF027 "No audio CD changer signals",
check the multiplex network (see 88B, Multiplex).
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and the connection of the receiver 32-track connector (component code 261), of the navigation
central control connector (component code 1657) and of the navigation computer 32-track connector (component
code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in fault status (present → stored).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, wiring: Precautions for repair), repair the connector(s); otherwise, replace the wiring.
With ignition on, check for + 12 V on connection BCP3 of the 8-track connector on component 261.
Check that the earth on the MT connection of the 8-track connector on component 261 is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 107W,
●connection code 107X,
●connection code 34HU,
between components 1657 and 261.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF022ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 18V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF023
PRESENT
OR
STOREDNO DISPLAY MULTIPLEX SIGNAL
1.DEF : No communication with display
2.DEF : Display malfunction
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after it has
been cleared, the ignition turned off and on again and the navigation system started.
Use the Wiring Diagrams Technical Note, Scenic II.
1.DEF
NOTESNone
Check the condition and connection of the display connector (component code 1127) and of the navigation
computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in fault status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
With ignition on, check for + 12 V on the BCP3 connection of the component 1127 connector.
Check that the earth on the MAN connection of component 1127 is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, replace component 1127.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF023ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 20V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF025
PRESENT
OR
STOREDNO CENTRAL CONTROL MULTIPLEX SIGNAL
1.DEF : No communication with the central control
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the navigation
system started after using the central control several times.
If faults DF022 No radio multiplex signal, DF025 No central control multiplex
signal and DF027 No audio CD changer signals are present at the same time, check
the multimedia network (see 88B, Multiplexing).
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the navigation central control connector (component code 1657) and of the
navigation computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in fault status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
With ignition on, check for + 12 V on the BCP3 connection of component 1657.
Check that the earth on the MX connection on the component 1657 connector is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34DZ,
●connection code 34GA,
●connection code 34HU,
between components 1657 and 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF025ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 21V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF027
PRESENT
OR
STOREDNO AUDIO CD CHANGER SIGNALS
1.DEF : No communication with the CD changer keypad
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the audio
system started after using the CD multi-changer several times.
Order of priority in the event of more than one fault:
Deal with fault DF022 No radio multiplex signal first.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 15A fuse (component code 260) and the 7.5A fuse (component code 1337).
Check the condition and connection of the CD changer (component code 1272) and of the receiver C2 (green)
connector (component code 261) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
With ignition on, check for + 12 V on connections SP2, AP43 and BCP3 of the component 1272 connector.
Check that the earth on the MAN connection on the component 1272 connector is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34HT,
●connection code 34HR,
●connection code TB29,
●connection code 34HS,
between components 1272 and 261.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF027ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 23V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF030
PRESENT
OR
STOREDGPS AERIAL CIRCUIT
CO : Open circuit
NOTESConditions for applying the fault finding procedure to the stored fault:
Apply this fault finding procedure if the fault reappears as present or stored after it has
been cleared and the ignition has been switched off and on again.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the GPS aerial 2-track connectors (component code 886) and of the
navigation computer (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 46CB,
●connection code TB15,
between components 662 and 886.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the connections are correct, replace the GPS aerial.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF030ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 29V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of statuses
ET003
+ 12 V SIDE LIGHTS FEED
NOTESVisually check that the side lights are working. Carry out fault finding on the steering
column switches and the side lights.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 7.5 A fuse in the engine compartment connection unit (component code 1337).
Check the condition and connection of the navigation central control connectors (component code 1657) and of
the CD changer (component code 1272) (broken, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the LPG connection between
components 1337, 1272 and 1657.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET003ITSJ84ph2V1.0
MR-372-J84-86C050$624.mif