2008 NISSAN TEANA check engine

DIAGNOSIS AND REPAIR WORK FLOW
TM-177
< BASIC INSPECTION >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
 Stall test. Refer to TM-306, "Inspection and Judgment".
>> GO TO 3.
3.CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is detected.
 Record DTC.
 Erase DTC. Refer to TM-202, "
Diagnosis Description".
Is any DTC detected?
YES >> GO TO 4.
NO >> GO TO 5.
4.PERFORM DIAGNOSTIC PROCEDURE
Perform “Diagnostic Procedure” for the displayed DTC.
>> GO TO 5.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform “DTC CONFIRMATION PROCEDURE” for the displayed DTC.
Is DTC detected?
YES >> GO TO 4.
NO >> GO TO 6.
6.CHECK SYMPTOM 2
Confirm the symptom described by the customer.
Is any malfunction present?
YES >> GO TO 7.
NO >> INSPECTION END
7.ROAD TEST
Perform “ROAD TEST”. Refer to TM-310, "
Description".
>> GO TO 8.
8.CHECK SYMPTOM 3
Confirm the symptom described by the customer.
Is any malfunction present?
YES >> GO TO 2.
NO >> INSPECTION END
Diagnostic Work SheetINFOID:0000000003806345
INFORMATION FROM CUSTOMER
KEY POINTS
WHAT..... Vehicle & CVT model
WHEN..... Date, Frequencies
WHERE..... Road conditions
HOW..... Operating conditions, Symptoms
Customer name MR/MS Model & Year VIN
Trans. Model Engine Mileage
Malfunction Date Manuf. Date In Service Date
Frequencyo Continuouso Intermittent ( times a day)

TM-178
< BASIC INSPECTION >[CVT: RE0F10A]
DIAGNOSIS AND REPAIR WORK FLOW
DIAGNOSTIC WORK SHEET
Symptomso Vehicle does not move. (o Any positiono Particular position)
o No shift
o Lock-up malfunction
o Shift shock or slip (o N → Do N → Ro Lock-upo Any drive position)
o Noise or vibration
o No pattern select
o Others
()
Malfunction Indicator (MI)o Continuously lito Not lit
1o Read the item on cautions concerning fail-safe and understand the customer's complaint.TM-283
2o CVT fluid inspection, stall test and line pressure test
o CVT fluid inspection
TM-304
o Leak (Repair leak location.)
o State
o Amount
o Stall test
TM-306
,
TM-308
o Torque converter one-way clutch
o Reverse brake
o Forward clutch
o Steel belto Engine
o Line pressure low
o Primary pulley
o Secondary pulley
o Line pressure inspection - Suspected part:
3o Perform self-diagnosis.
TM-204
Enter checks for detected items.
4o Perform road test.TM-310
4-1. Check before engine is started TM-310
4-2. Check at idleTM-311
4-3. Cruise testTM-312
o Check malfunction phenomena to repair or replace malfunctioning part after completing all road tests. Refer to TM-286,
"Symptom Table".
5o Drive vehicle to check that the malfunction phenomenon has been resolved.
6o Erase the results of the self-diagnosis from the TCM and the ECM.TM-202
,
TM-204

INSPECTION AND ADJUSTMENT
TM-179
< BASIC INSPECTION >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Service After Replac-
ing TCM and Transaxle Assembly
INFOID:0000000003806346
SERVICE AFTER REPLACING TCM AND TRANSAXLE ASSEMBLY
Perform the applicable service according to the following sheet when replacing TCM or transaxle assembly.
CAUTION:
 Never start the engine until the service is completed.
 “TCM-POWER SUPPLY [P1701]” may be indicated soon after replacing TCM or transaxle assembly
(after erasing the memory at the pattern B). Restart the self-diagnosis after erasing the self-diagnosis
result. Check that no error is detected.
NOTE:
Old unit means that the unit has been already used for another vehicle.
PATTERN A
1. Shift the selector lever to “P” position after replacing TCM. Turn the ignition switch ON.
2. Check that the shift position indicator in the combination meter turns ON (It indicates approximately 1 or 2
seconds after turning the ignition switch ON.)
 Check the following items if the shift position indicator does not turn ON. Repair or replace the shift posi-
tion indicator if necessary.
- The harness between TCM and ROM ASSY in the transaxle assembly is open or shorted.
- Cable disconnected, loosen, or bent from the connector housing.
PATTERN B
1. Turn the ignition switch ON after replacing each part.
2. Start engine.
CAUTION:
Never start driving.
3. Select “Data Monitor” mode for “TRANSMISSION”.
4. Warm up the transaxle assembly until “ATFTEMP COUNT” indicates 47 [approximately 20°C (68°F)] or
more. Turn the ignition switch OFF.
5. Turn the ignition switch ON.
CAUTION:
Never start engine.
6. Select “Self Diagnostic Results” mode for “TRANSMISSION”.
7. Shift the selector lever to “R” position.
8. Depress slightly the accelerator pedal (Pedal angle: 2/8) while depressing the brake pedal.
9. Perform “Erase”.
10. Shift the selector lever to “R” position after replacing TCM. Turn the ignition switch OFF.
11. Wait approximately 10 seconds after turning the ignition switch OFF.
12. Turn the ignition switch ON while shifting the selector lever to “R” position.
CAUTION:
Never start engine.
13. Select “Special Function” mode for “TRANSMISSION”.
14. Check that the value on “CALIBRATION DATA” is the same as the data after erasing “Calibration Data”.
TCM CVT assembly Service pattern
Replace the new unit. Do not replace the unit. “PATTERN A”
Do not replace the unit. Replace either an old unit or new unit.
“PATTERN B”
Replace the old unit.Do not replace the unit.
Replace either an old unit or new unit.
Replace the new unit. Replace either an old unit or new unit. “PATTERN C”

ON BOARD DIAGNOSTIC (OBD) SYSTEM
TM-203
< FUNCTION DIAGNOSIS >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
Only one set of freeze frame data (either 1st trip freeze frame data or freeze frame data) can be stored in the
ECM. 1st trip freeze frame data is stored in the ECM memory along with the 1st trip DTC. There is no priority
for 1st trip freeze frame data, and it is updated each time a different 1st trip DTC is detected. However, once
freeze frame data (2nd trip detection/MI on) is stored in the ECM memory, 1st trip freeze frame data is no
longer stored. Remember, only one set of freeze frame data can be stored in the ECM. The ECM has the fol-
lowing priorities to update the data.
Both 1st trip freeze frame data and freeze frame data (along with the DTC) are cleared when the ECM mem-
ory is erased.
How to Erase DTC
 The diagnostic trouble code can be erased by CONSULT-III, GST or ECM DIAGNOSTIC TEST MODE as
described below.
-If the battery cable is disconnected, the diagnostic trouble code will be lost within 24 hours.
-When erasing the DTC, using CONSULT-III or GST is easier and quicker than switching the mode
selector on the ECM.
 The following emission-related diagnostic information is cleared from the ECM memory when erasing DTC
related to OBD. For details, refer to EC-389, "
DTCIndex".
-Diagnostic trouble codes (DTC)
-1st trip diagnostic trouble codes (1st trip DTC)
-Freeze frame data
-1st trip freeze frame data
-System readiness test (SRT) codes
-Test values
How to Erase DTC (With CONSULT-III)
The emission related diagnostic information in the TCM and ECM can be erased by selecting “All Erase” in the
“Description” of “FINAL CHECK” mode with CONSULT-III.
How to Erase DTC (With GST)
1. If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.
2. Select Mode 4 with GST (Generic Scan Tool). For details, refer to EC-122, "
DiagnosisToolFunction".
MALFUNCTION INDICATOR (MI)
Description
The MI is located on the instrument panel.
1. The MI is turned ON when the ignition switch is turned ON with-
out the engine running. This is a bulb check.
 If the MI is not turned ON, refer to EC-346, "
Component Func-
tion Check".
2. The MI is turned OFF when the engine is started. If the MI
remains ON, the on board diagnostic system has detected an
engine system malfunction.
Priority Items
1
Freeze frame dataMisfire — DTC: P0300 - P0304
Fuel Injection System Function — DTC: P0171, P0172
2 Except the above items (Includes CVT related items)
3 1st trip freeze frame data
SAT652J

TM-204
< FUNCTION DIAGNOSIS >[CVT: RE0F10A]
DIAGNOSIS SYSTEM (TCM)
DIAGNOSIS SYSTEM (TCM)
CONSULT-III Function (TRANSMISSION)INFOID:0000000003806374
FUNCTION
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
WORK SUPPORT MODE
Display Item List
Engine Brake Adjustment
CAUTION:
Mode of “+1”“0”“−1”“−2”“OFF” can be selected by touching “UP” or “DOWN” on CONSULT-III screen.
However, do not select mode other than “0” and “OFF”. Selecting “+1” or “−1” or “−2” is selected, that
may cause irregular driveability.
Check CVT Fluid Deterioration Date
CAUTION:
Touch “CLEAR” after changing CVT fluid, and then erase “CVTF DETERIORATION DATE”.
SELF DIAGNOSTIC RESULT MODE
Display Items List
Refer to TM-284, "DTC Index".
DATA MONITOR MODE
Display Items List
Diagnostic test mode Function
Work Support This mode enables a technician to adjust some devices faster and more accurately.
Self Diagnostic Results Retrieve DTC from ECU and display diagnostic items.
Data Monitor Monitor the input/output signal of the control unit in real time.
CAN Diagnosis This mode displays a network diagnosis result about CAN by a diagram.
CAN Diagnosis Support Mon-
itorIt monitors the status of CAN communication.
ECU Identification Display the ECU identification number (part number etc.) of the selected system.
Special Function Other results or histories, etc. that are recorded in ECU are displayed.
Item name Description
ENGINE BRAKE ADJ. The engine brake level setting can be canceled.
CONFORM CVTF DETERIORTN The CVT fluid deterioration level can be checked.
“ENGINE BRAKE LEVEL”
0: Initial set value (Engine brake level control is activated)
OFF: Engine brake level control is deactivated.
“CVTF DETERIORATION DATE”
More than 210000:
It is necessary to change CVT fluid.
Less than 210000:
It is not necessary to change CVT fluid.

TM-208
< COMPONENT DIAGNOSIS >[CVT: RE0F10A]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000003806376
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H and CAN-L) allowing a high rate of information transmission with
less wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000003806377
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.
1.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Start engine and wait for at least 6 seconds.
3. Select “Self Diagnostic Results” mode for “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“U1000 CAN COMM CIRCUIT” detected?
YES >> Go to TM-208, "Diagnosis Procedure".
NO >> Check intermittent incident. Refer to GI-35, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000003806378
1.CHECK CAN COMMUNICATION CIRCUIT
With CONSULT-III
1. Turn ignition switch ON and start engine.
2. Select “Self Diagnostic Results” mode for “TRANSMISSION”.
Is
“U1000 CAN COMM CIRCUIT” indicated?
YES >> Go to LAN section. Refer to LAN-22, "CAN System Specification Chart".
NO >> Check intermittent incident. Refer to GI-35, "
Intermittent Incident".
DTCItem
(CONSULT-III screen term)Malfunction is detected
when...Possible cause
U1000 CAN COMM CIRCUITWhen TCM is not transmitting
or receiving CAN communica-
tion signal for 2 seconds or
more.Harness or connectors
(CAN communication line is
open or shorted.)

U1010 CONTROL UNIT (CAN)
TM-209
< COMPONENT DIAGNOSIS >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
U1010 CONTROL UNIT (CAN)
DescriptionINFOID:0000000003806379
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H and CAN-L) allowing a high rate of information transmission with
less wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000003806380
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.
1.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Start engine and wait for at least 6 seconds.
3. Select “Self Diagnostic Results” mode for “TRANSMISSION”.
Is
“U1010 CONTROL UNIT (CAN)” detected?
YES >> Go to TM-209, "Diagnosis Procedure".
NO >> Check intermittent incident. Refer to GI-35, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000003806381
1.CHECK CAN COMMUNICATION CIRCUIT
With CONSULT-III
1. Turn ignition switch ON and start engine.
2. Select “Self Diagnostic Results” mode for “TRANSMISSION”.
Is
“U1010 CONTROL UNIT (CAN)” indicated?
YES >> Replace the TCM. Refer to TM-315, "Exploded View".
NO >> Check intermittent incident. Refer to GI-35, "
Intermittent Incident".
DTCItem
(CONSULT-III screen term)Malfunction is detected when... Possible cause
U1010 CONTROL UNIT (CAN)When detecting error during the
initial diagnosis of CAN control-
ler to TCM.Harness or connectors
(CAN communication line is
open or shorted.)

TM-210
< COMPONENT DIAGNOSIS >[CVT: RE0F10A]
P0703 STOP LAMP SWITCH
P0703 STOP LAMP SWITCH
DescriptionINFOID:0000000003806382
BCM detects ON/OFF state of the stop lamp switch and transmits the data to the CVT control unit via CAN
communication by converting the data to a signal.
DTC LogicINFOID:0000000003806383
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.
1.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Start engine.
3. Drive vehicle for at least 3 consecutive seconds.
4. Select “Self Diagnostic Results” mode for “TRANSMISSION”.
Is
“P0703 BRAKE SW/CIRC” detected?
YES >> Go to TM-210, "Diagnosis Procedure".
NO >> Check intermittent incident. Refer to GI-35, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000003806384
1.CHECK STOP LAMP SWITCH CIRCUIT
1. Check and adjust the installation position of stop lamp switch. Refer to BR-6, "
Inspection and Adjustment".
2. Disconnect BCM connector.
3. Check voltage between BCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 2.
2.CHECK HARNESS BETWEEN STOP LAMP SWITCH AND BCM (PART 1)
1. Disconnect stop lamp switch connector.
2. Check continuity between stop lamp switch vehicle side harness connector terminal and BCM vehicle side
harness connector terminal.
DTCItem
(CONSULT-III screen term)Malfunction is detected when... Possible cause
P0703 BRAKE SW/CIRCWhen the brake switch does
not switch to ON or OFF. Harness or connectors
- (Stop lamp switch, and BCM
circuit are open or shorted.)
- (CAN communication line is
open or shorted.)
 Stop lamp switch
BCM vehicle side harness connector
GroundCondition Voltage (Approx.)
Connector Terminal
M123 118Depressed brake pedal Battery voltage
Released brake pedal 0 V