2008 NISSAN TEANA relay

SEC-90
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B2617 STARTER RELAY CIRCUIT
4. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
IPDM E/R BCM
Continuity
Connector Terminal Connector Terminal
E11 46 M121 52 Existed
IPDM E/R
GroundContinuity
Connector Terminal
E11 46 Not existed

SEC-96
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B2108 STEERING LOCK RELAY
B2108 STEERING LOCK RELAY
DescriptionINFOID:0000000003815038
The steering lock relay ON signal is transmitted to IPDM E/R by BCM via CAN communication.
IPDM E/R turns the steering lock relay ON and transmits the release of the steering to BCM.
DTC LogicINFOID:0000000003815039
DTC DETECTION LOGIC
NOTE:
If DTC B2108 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-
28, "IPDM E/R : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Press the push-button ignition switch under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-96, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815040
1.CHECK STEERING LOCK RELAY
Check voltage between IPDM E/R harness connector and ground.
Is the inspection normal?
YES >> GO TO 2.
NO >> Replace IPDM E/R. Refer to PCS-34, "
Removal and Installation".
2.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B2108 STRG LCK RELAY ONIPDM E/R detects that the relay is stuck in the ON
position for about 1 second even if the IPDM E/R re-
ceives steering lock relay ON/OFF signal from BCM.IPDM E/R
(+)
(–) ConditionVoltage (V)
(Approx.) IPDM E/R
Connector Terminal
E10 11 GroundIgnition switch
OFFA few seconds after
opening the driver doorBattery voltage
Ignition switch
LOCKPress the push-button
ignition switchBattery voltage
Ignition switch ACC or ON 0

B2109 STEERING LOCK RELAY
SEC-97
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2109 STEERING LOCK RELAY
DescriptionINFOID:0000000003815041
The steering lock relay ON signal is transmitted to IPDM E/R by BCM via CAN communication.
IPDM E/R turns the steering lock relay ON and transmits the release of the steering to BCM.
DTC LogicINFOID:0000000003815042
DTC DETECTION LOGIC
NOTE:
 If DTC B2109 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
IPDM E/R : DTC Logic".
 When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B2109 may be
detected.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Press the push-button ignition switch under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-97, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815043
1.CHECK POWER SUPPLY CIRCUIT
Check IPDM E/R power supply circuit. Refer to PCS-19, "
Diagnosis Procedure".
Is the circuit normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10A fuse (No. 48, located in IPDM E/R).
Is the inspection normal?
YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".
NO >> Check the following.
 Harness for open or short between IPDM E/R and battery
Fuse
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B2109STRG LCK RELAY
OFFIPDM E/R detects that the relay is stuck in the OFF
position for about 1 second even if the IPDM E/R
receives steering lock relay ON/OFF signal from
BCM. Harness or connector (Power sup-
ply circuit)
IPDM E/R
 Battery

SEC-102
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B210B STARTER CONTROL RELAY
B210B STARTER CONTROL RELAY
DescriptionINFOID:0000000003815047
Starter control relay, integrated in IPDM E/R, permits the starter relay operation when in the N or P position
and the steering is locked or unlocked. It is installed in parallel with the starter relay.
DTC LogicINFOID:0000000003815048
DTC DETECTION LOGIC
NOTE:
If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-
28, "IPDM E/R : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the power supply position to start under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-102, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815049
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” for IPDM E/R with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-191, "
DTCIndex".
Is the DTC B210B displayed again?
YES >> Replace IPDM E/R. Refer PCS-34, "Removal and Installation".
NO >> INSPECTION END
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B210BSTART CONT RLY
ONIPDM E/R detects that the relay is stuck in the ON
position even if the followings conditions are met for
about 1 second.
 Starter control relay ON/OFF signal from BCM
 Park neutral position (PNP) switch input signalIPDM E/R

B210C STARTER CONTROL RELAY
SEC-103
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B210C STARTER CONTROL RELAY
DescriptionINFOID:0000000003815050
Starter control relay, integrated in IPDM E/R, permits the starter relay operation when in the N or P position
and the steering is locked or unlocked. It is installed in parallel with the starter relay.
DTC LogicINFOID:0000000003815051
DTC DETECTION LOGIC
NOTE:
 If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
IPDM E/R : DTC Logic".
 When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be
detected.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the power supply position to start under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-103, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815052
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” for IPDM E/R with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-103, "
DTC Logic".
Is the DTC B210C displayed again?
YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".
NO >> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B210C START CONT RLY OFFIPDM E/R detects that the relay is stuck in the OFF po-
sition even if the followings conditions are met for about
1 second.
 Starter control relay ON/OFF signal from BCM
 Park neutral position (PNP) switch input signalIPDM E/R
 Battery

SEC-104
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B210D STARTER RELAY
B210D STARTER RELAY
DescriptionINFOID:0000000003815053
Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition
switch is in the START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communica-
tion.
DTC LogicINFOID:0000000003815054
DTC DETECTION LOGIC
NOTE:
 If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
IPDM E/R : DTC Logic".
 If DTC B210D is displayed with DTC B2617, first perform the trouble diagnosis for DTC B2617. Refer to
SEC-89, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-104, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815055
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” for IPDM E/R with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-104, "
DTC Logic".
Is the DTC B210D displayed again?
YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".
NO >> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B210D STARTER RELAY ONIPDM E/R detects that the relay is stuck in the ON posi-
tion even if the followings conditions are met for about
1 second.
 Starter control relay ON/OFF signal from BCM
 Park neutral position (PNP) switch inputIPDM E/R

B210E STARTER RELAY
SEC-105
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B210E STARTER RELAY
DescriptionINFOID:0000000003815056
Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition
switch is in the START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communica-
tion.
DTC LogicINFOID:0000000003815057
DTC DETECTION LOGIC
NOTE:
 If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
IPDM E/R : DTC Logic".
 If DTC B210E is displayed with DTC B2110 for IPDM E/R, first perform the trouble diagnosis for DTC B2110.
Refer to SEC-109, "
DTC Logic".
 If DTC B210E is displayed with DTC B2617 for BCM, first perform the trouble diagnosis for DTC B2617.
Refer to SEC-89, "
DTC Logic".
 When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be
detected.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-105, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815058
1.CHECK STARTER RELAY OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between BCM harness connector and IPDM E/R harness connector.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B210E STARTER RELAY OFFIPDM E/R detects that the relay is stuck in the OFF position even if
the followings conditions are met for about 1 second.
 Starter control relay ON/OFF signal from BCM
 Park neutral position (PNP) switch input IPDM E/R
Battery
(+)
(–)Condition
Voltage (V)
(Approx.) BCM
Connector Terminal Ignition switch Brake pedal Selector lever
M121 52 Ground ON DepressedP or N Battery voltage
Other than
above0

SEC-106
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B210E STARTER RELAY
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK STARTER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".
NO >> Check harness for open or short between IPDM E/R and battery. Refer to SEC-186, "
Wiring Dia-
gram - IPDM E/R -".
BCM IPDM E/R
Continuity
Connector Terminal Connector Terminal
M121 52 E11 46 Existed
BCM
GroundContinuity
Connector Terminal
M121 52 Not existed
(+)
(–)Voltage (V)
(Approx.) IPDM E/R
Connector Terminal
E10 36 Ground Battery voltage