2008 NISSAN TEANA wheel

TM-184
< FUNCTION DIAGNOSIS >[CVT: RE0F10A]
MECHANICAL SYSTEM
System Diagram
INFOID:0000000003806350
System DescriptionINFOID:0000000003806351
Transmits the power from the engine to the drive wheel.
JPDIA0743GB

TM-186
< FUNCTION DIAGNOSIS >[CVT: RE0F10A]
MECHANICAL SYSTEM
Component Description
INFOID:0000000003806353
Item Function
Torque converterThe torque converter is the device that increases the engine torque as well as the conventional
CVT and transmits it to the transaxle.
Oil pumpThe efficiency of pump discharge rate has been increased at low-rpm and optimized at high-rpm
by adopting a vane-type oil pump controlled by the engine. Discharged oil from oil pump is trans-
mitted to the control valve. It is used as the oil of primary and secondary pulley operation and the
oil of clutch operation and the lubricant for each part.
Planetary gear
Perform the transmission of drive power and the switching of forward/backward movement. Forward clutch
Reverse brake
Primary pulley It is composed of a pair of pulleys (the groove width is changed freely in the axial direction) and
the steel belt (the steel star wheels are placed continuously and the belt is guided with the mul-
tilayer steel rings on both sides). The groove width changes according to wrapping radius of steel
belt and pulley from low status to overdrive status continuously with non-step. It is controlled with
the oil pressures of primary pulley and secondary pulley. Secondary pulley
Steel belt
Output gear
Reduction gear consists of primary deceleration (output gear and idler gear in pair) and second-
ary deceleration (reduction gear and final gear in pair). Each of them uses a helical gear. Idler gear
Reduction gear
Final gear
Differential
Manual shaft
The parking rod rotates the parking pole and the parking pole engages with the parking gear
when the manual shaft is in P position. As a result the parking gear and the output axis are fixed. Parking rod
Parking pawl
Parking gear

PRECAUTIONS
TM-297
< PRECAUTION >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003901473
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
 To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000003901477
NOTE:
 Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
 After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
 Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.

TM-314
< ON-VEHICLE MAINTENANCE >[CVT: RE0F10A]
CVT POSITION
CVT POSITION
Inspection and AdjustmentINFOID:0000000003806512
INSPECTION
1. Place selector lever in “P” position, and turn ignition switch ON (engine stop).
2. Check that selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
check that selector lever can be shifted from “P” position only when brake pedal is depressed.
3. Move the selector lever and check for excessive effort, sticking, noise or rattle.
4. Check that selector lever stops at each position with the feel of engagement when it is moved through all
the positions. Check that the actual position of the selector lever matches the position shown by the shift
position indicator and the manual lever on the transaxle.
5. The method of operating the selector lever to individual posi-
tions correctly should be as shown.
6. When selector button is pressed in “P”, “R”, “N”, “D” or “L” posi-
tion without applying forward/backward force to selector lever,
check button operation for sticking.
7. Check that back-up lamps illuminate only when selector lever is
placed in the “R” position.
8. When in “R” position, check that back-up lamps illuminate even
when the selector lever is pushed toward the “P” position.
CAUTION:
Check the lighting without pressing shift button.
9. Check that the back-up lamps do not illuminate when selector lever is pushed toward the “R” position
when in the “P” or “N” position.
CAUTION:
Check the lighting without pressing shift button.
10. Check that the engine can only be started with the selector lever in the “P” and “N” positions.
11. Check that transaxle is locked completely in “P” position.
ADJUSTMENT
1. Place selector lever in “ P” position.
CAUTION:
Turn wheels more than 1/4 rotations and apply the park lock.
2. Loosen nut (A) and place manual lever (B) in “P” position.
CAUTION:
Never apply any force to the manual lever.
3. Tighten nut. Refer to TM-319, "
Exploded View".
CAUTION:
Fix the manual lever when tightening.
JPDIA0343GB
JPDIA0780ZZ

VTL-1
VENTILATION, HEATER & AIR CONDITIONER
C
DE
F
G H
J
K L
M
SECTION VTL
A
B
VTL
N
O P
CONTENTS
VENTILATION SYSTEM
WITHOUT 7 INCH DISPLAY
FUNCTION DIAGNOSIS .. .............................
5
SWITCHES AND THEIR CONTROL FUNC-
TION ............................................................... .....
5
System Description ............................................. ......5
AIR DISTRIBUTION ............................................6
System Description ............................................. ......6
PRECAUTION ...............................................7
PRECAUTIONS .............................................. .....7
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
7
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect .....................................
7
Precaution for Procedure without Cowl Top Cover ......8
Precautions For Xenon Headlamp Service ...............8
Working with HFC-134a (R-134a) .............................8
General Refrigerant Precaution ................................8
Refrigerant Connection .............................................9
Service Equipment ..................................................11
COMPRESSOR .............................................. ....14
General Precautions ........................................... ....14
FLUORESCENT LEAK DETECTOR .................15
General Precautions ........................................... ....15
PREPARATION ...........................................16
PREPARATION .............................................. ....16
Special Service Tool ........................................... ....16
Commercial Service Tool ........................................18
Sealant or/and Lubricant .........................................18
ON-VEHICLE MAINTENANCE ....................20
AIR CONDITIONER FILTER .......................... ....20
Exploded View .................................................... ....20
Removal and Installation ..................................... ....20
Replacement ...........................................................20
ON-VEHICLE REPAIR .................................21
A/C CONTROL ..................................................21
Exploded View ..................................................... ....21
Removal and Installation .........................................21
A/C DISPLAY ....................................................22
Exploded View .........................................................22
Removal and Installation .........................................22
A/C AUTO AMP. ...............................................23
Exploded View .........................................................23
Removal and Installation .........................................23
AMBIENT SENSOR ..........................................24
Exploded View .........................................................24
Removal and Installation .........................................24
IN-VEHICLE SENSOR ......................................25
Exploded View .........................................................25
Removal and Installation .........................................25
SUNLOAD SENSOR .........................................26
Exploded View .........................................................26
Removal and Installation .........................................26
INTAKE SENSOR .............................................27
Exploded View .........................................................27
Removal and Installation .........................................28
BLOWER UNIT .................................................29
Exploded View .........................................................29
Removal and Installation .........................................30
BLOWER MOTOR ............................................32
Exploded View .........................................................32
Removal and Installation .........................................32
INTAKE DOOR MOTOR ...................................33
Exploded View .........................................................33

VTL-2
Removal and Installation ........................................33
HEATER & COOLING UNIT ASSEMBLY .........35
Exploded View ........................................................35
Removal and Installation ........................................37
MODE DOOR MOTOR ......................................40
Exploded View ........................................................40
Removal and Installation ........................................40
AIR MIX DOOR MOTOR ....................................41
Exploded View ........................................................41
Removal and Installation ........................................41
HEATER CORE .................................................43
Exploded View ........................................................43
Removal and Installation ........................................44
DUCT AND GRILLE ..........................................45
CENTER VENTILATOR GRILLE ..............................45
CENTER VENTILATOR GRILLE : Exploded View ...45
CENTER VENTILATOR GRILLE : Removal and
Installation ..............................................................
45
SIDE VENTILATOR GRILLE ....................................45
SIDE VENTILATOR GRILLE : Exploded View .......46
SIDE VENTILATOR GRILLE : Removal and In-
stallation .................................................................
46
SIDE DEFROSTER GRILLE .....................................46
SIDE DEFROSTER GRILLE : Exploded View ........47
SIDE DEFROSTER GRILLE : Removal and In-
stallation .................................................................
47
VENTILATOR DUCT .................................................47
VENTILATOR DUCT : Exploded View ...................48
VENTILATOR DUCT : Removal and Installation ....48
SIDE DEFROSTER NOZZLE ....................................49
SIDE DEFROSTER NOZZLE : Exploded View ......49
SIDE DEFROSTER NOZZLE : Removal and In-
stallation .................................................................
49
DEFROSTER NOZZLE .............................................50
DEFROSTER NOZZLE : Exploded View ................50
DEFROSTER NOZZLE : Removal and Installation
...
51
REAR VENTILATOR GRILLE ..................................51
REAR VENTILATOR GRILLE : Exploded View ......52
REAR VENTILATOR GRILLE : Removal and In-
stallation .................................................................
52
REAR VENTILATOR DUCT 1 ...................................52
REAR VENTILATOR DUCT 1 : Exploded View .....53
REAR VENTILATOR DUCT 1 : Removal and In-
stallation .................................................................
53
REAR VENTILATOR DUCT 2 ...................................53
REAR VENTILATOR DUCT 2 : Exploded View .....54
REAR VENTILATOR DUCT 2 : Removal and In-
stallation .................................................................
54
REAR FOOT DUCT 1 ................................................54
REAR FOOT DUCT 1 : Exploded View ..................55
REAR FOOT DUCT 1 : Removal and Installation ...55
REAR FOOT DUCT 2 ................................................56
REAR FOOT DUCT 2 : Exploded View ..................56
REAR FOOT DUCT 2 : Removal and Installation ...56
REAR FOOT DUCT 3 ................................................57
REAR FOOT DUCT 3 : Exploded View ..................58
REAR FOOT DUCT 3 : Removal and Installation ...58
FOOT DUCT ..............................................................59
FOOT DUCT : Exploded View ................................59
FOOT DUCT : Removal and Installation .................60
WITH 7 INCH DISPLAY
FUNCTION DIAGNOSIS ............................
61
SWITCHES AND THEIR CONTROL FUNC-
TION ...................................................................
61
WITHOUT INTELLIGENT AIR CONDITIONER
SYSTEM ....................................................................
61
WITHOUT INTELLIGENT AIR CONDITIONER
SYSTEM : System Description ...............................
61
WITH INTELLIGENT AIR CONDITIONER SYS-
TEM ...........................................................................
62
WITH INTELLIGENT AIR CONDITIONER SYS-
TEM : System Description ......................................
62
AIR DISTRIBUTION ..........................................63
System Description .................................................63
PRECAUTION ............................................64
PRECAUTIONS .................................................64
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
64
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect ...................................
64
Precaution for Procedure without Cowl Top Cover ...65
Precautions For Xenon Headlamp Service .............65
Working with HFC-134a (R-134a) ...........................65
General Refrigerant Precaution ..............................65
Refrigerant Connection ...........................................66
Service Equipment ..................................................68
COMPRESSOR .................................................71
General Precautions ...............................................71
FLUORESCENT LEAK DETECTOR .................72
General Precautions ...............................................72
PREPARATION ..........................................73
PREPARATION .................................................73
Special Service Tool ...............................................73
Commercial Service Tool ........................................75
Sealant or/and Lubricant .........................................75

PRECAUTIONS
VTL-7
< PRECAUTION >[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003845339
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000003845340
NOTE:
 Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
 After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
 Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.

VTL-64
< PRECAUTION >[WITH 7 INCH DISPLAY]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003894443
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
 To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000003894445
NOTE:
 Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
 After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
 Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.