2008 NISSAN TEANA height adjustment

BR-6
< ON-VEHICLE MAINTENANCE >
BRAKE PEDAL
ON-VEHICLE MAINTENANCE
BRAKE PEDAL
Inspection and AdjustmentINFOID:0000000003811172
INSPECTION
Brake Pedal Height
Check the brake pedal height (H1) between the dash lower panel (1)
and the brake pedal upper surface.
CAUTION:
Remove the floor trim.
Stop Lamp Switch and ASCD Brake Switch
Check the clearance (C) between stopper rubber (1) and stop lamp
switch and ASCD brake switch (2) threaded end.
CAUTION:
The stop lamp must be turned off when the brake pedal is
released.
NOTE:
Pull the brake pedal pad to make the clearance between stopper
rubber and stop lamp switch and ASCD brake switch threaded end.
Brake Pedal Play
Press the brake pedal. Check the brake pedal play (A).
Depressed Brake Pedal Height
Check the brake pedal height (H2) between the dash lower panel (1)
and the brake pedal upper surface when depressing the brake pedal
at 490 N (50 kg, 110 lb) while turning engine ON.
CAUTION:
Remove the floor trim.Standard
H
1: Refer to BR-45, "Brake
Pedal".
JPFIA0065ZZ
Standard
C : Refer to BR-45, "
Brake
Pedal".
JPFIA0122ZZ
Standard
A : Refer to BR-45, "
Brake
Pedal".
JPFIA0121ZZ
Standard
H
2: Refer to BR-45, "Brake
Pedal".
JPFIA0068ZZ

BRAKE PEDAL
BR-7
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
MA
B
BR
N
O
P
ADJUSTMENT
Brake Pedal Height
1. Remove instrument lower panel LH. Refer to IP-11, "Exploded View".
2. Disconnect the stop lamp switch and ASCD brake switch harness connector.
3. Turn the stop lamp switch and ASCD brake switch 45° counterclockwise.
4. Loosen the input rod lock nut (1). Adjust the brake pedal height
(H
1) to the specification. Tighten the input rod lock nut to the
specification. Refer to BR-28, "
Exploded View".
CAUTION:
The threaded end of the input rod (2) must project to the
inner side (L) of the clevis (3).
Stop Lamp Switch and ASCD Brake Switch
1. Remove instrument lower panel LH. Refer to IP-11, "Exploded View".
2. Disconnect the stop lamp switch and ASCD brake switch harness connector.
3. Turn the stop lamp switch and ASCD brake switch 45° counterclockwise.
4. Press-fit stop lamp switch and ASCD brake switch (2) until stop
lamp switch and ASCD brake switch hits the stopper rubber (1)
45° clockwise.
CAUTION:
 The clearance (C) between the stopper rubber and stop
lamp switch and ASCD brake switch threaded end must
be the specified value. Refer to BR-45, "
Brake Pedal".
 The stop lamp must be turned off when the brake pedal is
released.
Brake Pedal Play
1. Remove instrument lower panel LH. Refer to IP-11, "Exploded View".
2. Disconnect the stop lamp switch and ASCD brake switch harness connector.
3. Turn the stop lamp switch and ASCD brake switch 45° counterclockwise.
JPFIA0003ZZ
Standard
H
1: Refer to BR-45, "Brake
Pedal".
JPFIA0279ZZ
JPFIA0122ZZ

HOOD
DLK-193
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
 Front grille: Refer to EXT-18, "Removal and Installation".
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 After installing, perform hood fitting adjustment. Refer to DLK-193, "
HOOD ASSEMBLY : Adjust-
ment".
 After installing, perform front washer nozzle and tube inspection and adjustment. Refer to WW-102,
"Inspection and Adjustment".
HOOD ASSEMBLY : AdjustmentINFOID:0000000003813385
Check the clearance and the surface height between hood and each part visually and by touching. (Fitting
standard dimension in the table below should be satisfied.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1. Remove hood lock and adjust the height by rotating hood bumper rubber (side, lower) until hood becomes
1 to1.5 mm (0.039 to 0.059 in) lower than fender.
2. Temporarily tighten hood lock assembly, and position by engaging it with hood striker. Check hood lock
and striker for looseness and adjust the clearance and evenness with striker to satisfy the specification.
3. Adjust A and B shown in the figure to the following value with hood's own weight by dropping it from
approximately 200 mm (7.874 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5 lb)].
4. After adjustment, tighten lock bolts to the specified torque.
HOOD HINGE
Portion StandardDifference
(RH/LH, MAX)
Hood – Front bumper
fasciaA – A D Clearance3.7 – 8.3
(0.146 – 0.315)2.0
(0.079)
Hood – Front combina-
tion lampB – B E Clearance2.4 – 6.8
(0.094 – 0.268)2.5
(0.098)
Hood – Front fender C – CF Clearance3.1 – 6.1
(0.122 – 0.240)2.0
(0.079)
G Surface height−1.5 – 1.5
(−0.059 – 0.059)—
1. Hood striker 2. Primary latch 3. Secondary striker
4. Secondary latch
A : 20.0 mm (0.787 in)
B : 6.8 mm (0.268 in)
JMKIA2399ZZ

FRONT DOOR
DLK-203
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
 Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
 After installation, perform the fitting adjustment. Refer to DLK-203, "
DOOR ASSEMBLY : Adjust-
ment".
 After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR ASSEMBLY : AdjustmentINFOID:0000000003813396
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1. Remove front fender. Refer to DLK-199, "Removal and Installation".
2. Loosen door hinge mounting nuts on door side.
3. Adjust the surface height of front door according to the fitting standard dimension.
4. Temporarily tighten door hinge mounting nuts on door side.
5. Loosen door hinge mounting bolts on body side.
6. Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7. After adjustment tighten bolts and nuts to the specified torque.
8. Install front fender. Refer to DLK-199, "
Removal and Installation".
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded ViewINFOID:0000000003819380
Portion Clearance Surface height
Front fender – Front door A – A 2.6 – 4.6 (0.102 – 0.181)−1.0 – 1.0 (−0.039 – 0.039)
Front door – Rear door B – B 3.6 – 5.6 (0.142 – 0.220)−1.0 – 1.0 (−0.039 – 0.039)
JMKIA2384ZZ

REAR DOOR
DLK-209
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
 Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
 After installation, perform the fitting adjustment. Refer to DLK-209, "
DOOR ASSEMBLY : Adjust-
ment".
 After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR ASSEMBLY : AdjustmentINFOID:0000000003813405
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and surface height are out of specification, adjust them according to the procedures shown
below.
Unit: mm (in)
1. Remove center pillar lower garnish. Refer to INT-39, "Removal and Installation".
2. Loosen door hinge mounting nuts on door side.
3. Adjust the surface height of rear door according to the fitting standard dimension.
4. Temporarily tighten door hinge mounting nuts on door side.
5. Loosen door hinge mounting nuts and bolts on body side.
6. Raise rear door at rear end to adjust clearance of the rear door according to the fitting standard dimen-
sion.
7. After adjustment, tighten bolts and nuts to the specified torque.
8. Install center pillar lower garnish. Refer to INT-39, "
Removal and Installation".
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded ViewINFOID:0000000003819605
Portion Clearance Surface height
Front door – Rear door B – B 3.6 – 5.6 (0.142 – 0.220) -1.0 – 1.0 (-0.039 – 0.039)
Rear door – Body side outer C – C 2.6 – 4.6 (0.102 – 0.181) -1.0 – 1.0 (-0.039 – 0.039)
JMKIA2385ZZ

TRUNK LID
DLK-215
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID ASSEMBLY : AdjustmentINFOID:0000000003813414
Check the clearance and surface height between trunk lid and each part by visually and touching.
If the clearance and surface height are out of specification, adjust them according to the procedures shown
below.
Unit: mm (in)
1. Loosen trunk lid hinge mounting bolts (trunk lid side).
2. Remove trunk rear finisher. Refer to INT-57, "
Removal and Installation".
3. Loosen trunk lid striker mounting bolts.
4. Lift up trunk lid approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check that it
is engaged firmly with trunk lid closed.
5. Check the clearance and surface height.
6. Finally tighten trunk lid hinge and trunk lid striker.
7. Install trunk rear finisher. Refer to INT-57, "
Removal and Installation".
TRUNK LID STRIKER ADJUSTMENT
Adjust trunk lid striker so that it becomes parallel with trunk lid lock insertion direction.
TRUNK LID STRIKER
Portion StandardDifference
(RH/LH, MAX)
Trunk lid – Body side outer A – AD Clearance2.5 – 4.5
(0.098 – 0.177)1.0 (0.039)
ESurface
height−1.5 – 0.5
(−0.059 – 0.020)1.4 (0.055)
Trunk lid – Rear combina-
tion lampB – BF Clearance2.9 – 6.5
(0.114 – 0.256)2.0 (0.079)
GSurface
height−2.3 – 1.3
(−0.091 – 0.051)2.0 (0.079)
Trunk lid – Rear bumper fas-
ciaC – C H Clearance5.0 – 9.0
(0.197 – 0.354)—

EXL-10
< BASIC INSPECTION >[XENON TYPE]
INSPECTION AND ADJUSTMENT
SENSOR INITIALIZE : Description
INFOID:0000000003774311
HEADLAMP AIMING CONTROL SYSTEM
Perform the sensor initialize when installing, removing and replacing the auto levelizer control unit and sus-
pension components.
SENSOR INITIALIZE : Special Repair Requirement (HEADLAMP AIMING CONTROL
SYSTEM)
INFOID:0000000003774312
1.VEHICLE CONDITION CHECK
1. Park the vehicle in the straight-forward position.
2. Unload the vehicle (no passenger aboard).
>> GO TO 2.
2.SENSOR INITIALIZE
CONSULT-III WORK SUPPORT
1. Select "SENSOR INITIALIZE" of HEADLAMP LEVELIZER work support item.
2. Select "START".
3. When "INITIALIZE COMPLETE", select "END".
CAUTION:
If "INITIALIZE NOT DONE" is indicated, auto levelizer control unit detects that the sensor lever sig-
nal changes. The sensor initialize is cancelled. In this case, turn the ignition switch OFF to prevent
the vehicle from the height change. Perform the sensor initialize again.
Is the sensor initialize completed?
YES >> GO TO 3.
NO >> Perform the sensor initialize again.
3.SELF-DIAGNOSIS RESULT CHECK
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected.
Is any DTC detected?
YES >> GO TO 2.
NO >> Sensor initialize completed

HEADLAMP AIMING ADJUSTMENT
EXL-175
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Low beam distribution on the screen
Unit: mm (in)
Aiming Adjustment Procedure (High Beam)INFOID:0000000003827917
1. Place the screen.
NOTE:
 Stop the vehicle at the perpendicular angle to the wall.
 Set the screen so that it is perpendicular to a level load surface.
JSLIA0030ZZ
A. Aiming adjustment area
B. Elbow point
C. Headlamp center
H. Horizontal center line of headlamp
V. Vertical center line of headlamp
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area
(lateral)Y. Aiming adjustment area
(Vertical)
Distance from headlamp center to screen (L) : 10m (32.8 ft)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)Lateral direction (X)
(Right and left side from headlamp centerline)
Highest light axis 100 (3.94)
0-100 (3.94) Target light axis 120 (4.72)
Lowest light axis 150 (5.91)
JPLIA1062ZZ