2008 NISSAN TEANA washer

HEADLAMP WASHER PUMP
WW-101
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
HEADLAMP WASHER PUMP
Exploded ViewINFOID:0000000003761629
Removal and InstallationINFOID:0000000003761630
REMOVAL
1. Remove the fender protector RH (front). Refer to EXT-22, "FENDER PROTECTOR : Exploded View".
2. Disconnect the headlamp washer pump connector.
3. Disconnect the headlamp washer tube.
4. Remove the headlamp washer pump from the washer tank.
5. Remove the packing from the washer tank.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never twist the packing when installing the headlamp washer pump.
1. Washer tank 2. Packing 3. Clip
4. Headlamp washer tube 5. Headlamp washer pump 6. Headlamp washer pump connector
JPLIA1136ZZ

WW-102
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
FRONT WASHER NOZZLE AND TUBE
Hydraulic LayoutINFOID:0000000003761632
Removal and InstallationINFOID:0000000003761633
REMOVAL
1. Open the hood.
2. Remove the washer nozzle in numerical order shown in the fig-
ure.
3. Disconnect the washer tube from the washer nozzle.
INSTALLATION
1. Connect the washer tube into the washer nozzle.
2. Fix the pawl-side behind the washer nozzle first, then push the resin clip-side.
3. Adjust the washer nozzle spray position. Refer to WW-102, "
Inspection and Adjustment".
CAUTION:
The spray positions differ. Check that left and right nozzles are installed correctly.
Inspection and AdjustmentINFOID:0000000003761634
INSPECTION
Washer Nozzle Inspection
1. Washer nozzle 2. Washer tube 3. Washer tank
: Clip
JPLIA1137ZZ
: Vehicle front
JPLIA1138ZZ

FRONT WASHER NOZZLE AND TUBE
WW-103
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
Unit: mm (in)
JPLIA1139ZZ
1. End of cowl top cover
: Spray area
: Target spray position
Spray position H (Height) L (Width) Spray area
A 293.2 (11.54) 490.7 (19.32)φ 80 (3.15)
B 422.0 (16.61) 298.6 (11.76)φ 80 (3.15)
C 376.2 (14.81) 121.5 (4.78)φ 80 (3.15)
D 327.9 (12.91) 56.3 (2.22)φ 80 (3.15)
E 383.1 (15.08) 300 (11.81)φ 80 (3.15)
F 305.7 (12.04) 475.1 (18.70)φ 80 (3.15)
JPLIA1140ZZ

WW-104
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
JPLIA1141ZZ

FRONT WIPER ARM
WW-105
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
FRONT WIPER ARM
Exploded ViewINFOID:0000000003761635
Removal and InstallationINFOID:0000000003761636
REMOVAL
1. Operate the front wiper to move it to the auto stop position.
2. Open the hood.
3. Remove the wiper arm cap.
4. Remove the wiper arm mounting nut.
5. Raise wiper arm, and remove the wiper arm from the vehicle.
INSTALLATION
1. Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2. Operate the front wiper motor to move the wiper to the auto stop
position.
3. Adjust the wiper blade position. Refer to WW-105, "
Adjustment".
4. Install the wiper arm by tightening the mounting nut.
5. Inject the washer fluid.
6. Operate the front wiper to move it to the auto stop position.
7. Check that the wiper blades stop at the specified position.
8. Install the wiper arm cap.
AdjustmentINFOID:0000000003761637
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover and the top of wiper blade center
1. Wiper blade (RH) 2. Wiper arm (RH) 3. Wiper blade (LH)
4. Wiper arm (LH) 5. Wiper arm cap
Refer to GI-4, "
Components" for symbols in the figure.
JPLIA1142GB
ELH0717D

FRONT WIPER AND WASHER SWITCH
WW-109
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
FRONT WIPER AND WASHER SWITCH
Exploded ViewINFOID:0000000003761641
Refer to BCS-79, "Exploded View".