2008 MITSUBISHI SHOGUN change time

3-34 Instruments and controls
3
2. It is possible to adjust the clock using the function buttons
3. After making the adjustment, press the “INFO” button to
select the information display.
NOTE●
Vehicles equipped with the Mitsubishi Multi Communica- tion System (MMCS) also have a clock indication, but the time shown by the MMCS may differ from that shown by the centre information disp
lay because different sources
of data are used for automatic adjustment.
“H”- Adjust “hour”.
The indication increases by one hour, every time youlightly press the “H” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded, and then the setting ischanged to the hour selected.
“M”- Adjust “minute”.
The indication increases by one minute, every time youlightly press the “M” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded, and then the setting ischanged to the minute selected.
“SET”- To reset the minutes to zero.
The time is adjusted as described below by pressing thefunction button “SET”.●
10:30-11:29 · · · · Change to 11:00
●
11:30-12:29 · · · · Change to 12:00
In this occasion, the display flashes twice before the set-ting is changed.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
34 Wednesday, January 9, 2008 4:32 PM

3-36 Instruments and controls
3
3. Use the function buttons to adjust the brightness.
NOTE●
If you next wish to adjust the other adjustment setting (daytime or nighttime), press the “ADJ” button or “BACK” function button.
4. After adjustment, press the
“INFO” button to select the
information display.
NOTE●
As the display brightness can
be adjusted in the center
information display only, the brightness inside the meter cannot be changed.
“+”- To make the display brighter
The display becomes brighter by one step, every timeyou lightly press the “+” function button. If you con-tinue pressing the button for about 2 seconds or more,the indication is fast-forwarded.
“-”- To make the display darker
The display becomes darker by one step, every time youlightly press the “-” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded.
“SET”- To set the brightness
Press function button “SET” to set the new brightness.The display will flash twice.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
36 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-43
3
2. Press the “
←” or “
→” function button to select “CALEN-
DAR ADJUST”. Then press the “SELECT” function but- ton.
3. Use the function buttons to set the calendar." →"- Select “YEAR”, “MONTH”, “DAY” you wish to
change.“YEAR”, “MONTH”, and “DAY” are changed over byturns every time you lightly press the “
→” function but-
ton.
“+”- Change “YEAR”, “MONTH”, “DAY” you have
selected.The indication is changed to your desired date everytime you lightly press the “+” function button.If you continue pressing the button for about 2 secondsor more, the indication is forwarded.
“SET”- Determine the date.
Press the “SET” function button. Then the displayflashes twice and the setting is changed.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
43 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-47
3
2. Press the function button “
←” or “
→ ” to select the item
you wish to set. · “UNIT”: Changing the unit · “LANGUAGE”: Changing the language· “12h
↔
24h”: Changing the time format
· “DEFAULT”: Resetting to factory settings Push the function button “SELECT”. The setting displayfor your selected item will appear.
Changing display units It is possible to change the display units for the fuel consump- tion, driving range, average speed
, outside temperature, eleva-
tion, and atmospheric pressure as shown below.FUEL ECONOMY
km/L
→ L/100km
→ mpg
(UK GALLON)
→ mpg (US GALLON)
RANGE km
→ miles
SPEED km/h
→ mph
OUTSIDE TEMPERATURE
°C
→ °F
ELEVATION m
→ ft
atmospheric pressure
hPa
→ mb
→ kPa
→ inHg
BK-BK2008E1ENUK.en-uk-Section6.fm Page
47 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-61
3
Dipper (High/Low beam change)
E00506200055
When the lamp switch is in the “ ” position, the beam changes from high to low (or low
to high) each time the lever is
pulled fully (1). While the high b
eam is on, the high beam indi-
cation lamp in the instrument cluster will also illuminate.
Headlamp flasher
E00506300128
The high beams flash when the lever is pulled slightly to (2), and will go off when it is released. When the high beam is on, th
e high beam indication lamp in
the instrument cluster will illuminate.NOTE●
The high beams can also flash when the lamp switch is OFF.
●
If you turn the lamps off with the headlamps set to high beam, the headlamps are automa
tically returned to their
low-beam setting when the lamp
switch is next turned to
the “ ” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
61 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-65
3
Turn-signal lever
E00506500771
NOTE●
If the lamp flashes unusually quickly, the bulb in a turn- signal lamp may have burned out. We recommend you to have the vehicle inspected.
●
It is possible to activate the following functions. For fur- ther information, we recommend you to consult a MIT- SUBISHI MOTORS Author
ized Service Point.
• Sounding of a buzzer as the turn-signal lamps flash• Flashing of the turn-signal lamps when the lever is oper- ated with the ignition switch in the “ACC” position • The turn signal-lamps 3-flash function for lane changescan be deactivated. • The time required to operate the lever for the 3-flash function can be adjusted.
1- Turn-signals
When making a normal turn, use position (1). The lever willreturn automatically when cornering is completed.
2- Lane-change signals
When changing lanes, use position (2). It will return to theneutral position when released.Also, when you move the lever to (2) slightly then release it,the turn-signal lamps and indication lamp in the instrumentcluster will flash 3 times.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
65 Wednesday, January 9, 2008 4:32 PM

4-16 Starting and driving
4
NOTE●
It is possible to adjust the period of ignition switch illumi- nation (the period until the ignition switch illumination goes off). For details, we recommend you to consult a MITSUBISHI MOTORS Auth
orized Service Point.
●
If the illumination period of the room & map lamps or rear personal lamps (the period until these lamps go off) is adjusted, the period of ignition switch illumination (theperiod until the ignition switch illumination goes off) will automatically be changed at the same time. If the illumination period of the room & map lamps or rearpersonal lamps is set to zero (in other words, the illumina- tion keep-on function is deactivated), the ignition switch illumination will not come on when the ignition switch isremoved. For information, we recommend you to consult a MIT- SUBISHI MOTORS Authorized Service Point.
To remove the keyFor vehicles with a M/T, when removing the key, push the keyin at the “ACC” position and keep it depressed until it is turnedto the “LOCK” position, and remove it.Vehicles with M/T
BK-BK2008E1ENUK.en-uk-Section7.fm Page
16 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-21
4
NOTE●
If the engine is cold, the di
esel preheat indication lamp is
on for a longer time.
●
When the engine has not been
started within about 5 sec-
onds after the diesel preheat
indication lamp went out,
return the ignition key to the “LOCK” position. Then, turn the key to the “ON” position to preheat the engine again.
●
When the engine is warm, th
e diesel preheat indication
lamp does not come on even
if the ignition key is placed
in the “ON” position. Start the engine by turning the ignition key right to the“START” position.
7. Turn the ignition key to the “START” position without
depressing the acceler
ator pedal, and release it when the
engine starts.
Fuel injection amount learning process (diesel- powered vehicles)
E00616000044
To keep exhaust emissions and engine noise low, the engine very occasionally performs a
learning process for the fuel
injection amount. The engine sounds slightly di
fferent from usual while the
learning process is taking pl
ace. The change in the engine
sound does not indicate a fault.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
21 Wednesday, January 9, 2008 4:36 PM