2008 MITSUBISHI SHOGUN start stop button

2-40 Seat and seat belts
2
3. Pull the belt slightly to adjust slackness as desired.To unfasten Hold the latch plate and pu
sh the button on the buckle.
NOTE●
As the belt retracts automatically, keep the latch plate held while retracting so that the belt stows slowly. Failure to dothis could damage the vehicle.
Seat belt reminder/warning lamp
E00409800338
The seat belt warning lamp is located on the instrument panel.A tone and warning lamp are used to remind the driver to fas- ten the seat belt. When the ignition key is turned to the “ON” position, the warn- ing lamp will illuminate and a tone will sound for about 6 sec- onds. If the driver’s seat belt remains unfastened for approximately 1 minute later, the warning lamp will flash andthe tone sound intermittently (each 12 times) when the vehicle is driven. If the driver subseq
uently unfastens the seat belt
while driving, the warning lamp and tone will issue furtherwarnings. And if the seat belt remains unfastened, the warning lamp and tone will issue further
warnings each time the vehicle
starts moving from a stop. When
the seat belt is fastened, the
warnings will stop.
WARNING
!●
Never wear the lap portio
n of the belt across your
abdomen. During accident
s it can press sharply
against abdomen and increa
se the risk of injury.
●
The seat belts must not be twisted when worn.
BK-BK2008E1ENUK.en-uk-Section5.fm Page
40 Wednesday, January 9, 2008 4:28 PM

4-6 Starting and driving
4
Parking brake
E00600500422
To park the vehicle, first bring it to a complete stop, fully apply the parking brake lever sufficiently to hold the vehicle.To apply the parking brakeNOTE●
Apply sufficient force to the parking brake lever to hold the vehicle stationary after
the foot brake is released.
●
If the parking brake does not hold the vehicle stationary after the foot brake is releas
ed, have your vehicle checked
immediately.
To release the parking brake
1- Pull the lever up without pushing the button at the end of
hand grip.
1- Pull the lever up slightly. 2- Push the button at the end of hand grip. 3- Push the lever downward.
BK-BK2008E1ENUK.en-uk-Section7.fm Page 6 Wednesday, January 9, 2008 4:36 PM

For pleasant driving
5-37
5
To listen to a CD
E00709601062
1. Insert a disc with the label facing up, and the CD player
will begin playing even if the radio is being used. The CD indicator (16), the track number and the playing time will appear on the display. The CD
player will also start play-
back when the CD button (4) is pressed with a disc in the player.
2. To stop the CD, turn off the power by pressing the PWR
button (2) or change over to radio mode by pressing the AM/FM buttons (1), or eject th
e disc by pressing the eject
button (7).
NOTE●
To adjust the volume and tone, refer to “To adjust the vol- ume” on page 5-21 and “To adjust the tone” on page 5-21.
●
For information concerning
the handling of compact
discs, refer to “Handling of compact discs” on page 5-74.
To listen to an MP3 CDThis CD player allows you to play MP3 (MPEG Audio Layer-3) files recorded on CD-ROMs,
CD-Rs (recordable CDs), and
CD-RWs (rewritable CDs) in ISO9660 Level 1/Level 2, Joliet, and Romeo formats. Each disc may have a maximum of16 trees, 100 folders, and 255 files per disc. During MP3 play- back, the unit can display ID3 tag information. For information concerning ID3 tag, refer to “CD text and MP3 title display” onpage 5-41. 1. Insert a disc containing MP3 files into the slot. 2. Press the CD button (4) for 2 seconds or longer to switch
to MP3 CD mode from normal music CD mode. The dis- play shows “READING”, then
playback will begin. The
folder number and
the track number will appear on the
display.
BK-BK2008E1ENUK.en-uk-Section8.fm Page
37 Wednesday, January 9, 2008 4:41 PM

For pleasant driving
5-41
5
To find the start of each track on a disc for playbackPress the SCAN button (14). “SCAN” will appear on the dis- play and the CD player
will play back th
e first 10 seconds of
each track on the selected disc. The track number will blink while the scan mode is selected.To exit the scan mode, press the SCAN button again.NOTE●
Once all tracks on the disc have been scanned, playback of the disc will restart from the beginning of the track thatwas playing when scanning started.
●
The scan mode will be canceled when radio or CD opera- tion is selected.
●
With a disc that contains both CD-DA and MP3 files, the scan mode causes only files of the same format (CD-DA only or MP3 files only) to be played.
To eject a discWhen the CD eject button (7) is
pressed, the disc automatically
stops and is ejected. The syst
em automatically switches to
radio mode.NOTE●
If you do not remove the disc before 15 seconds have elapsed, the CD player will
automatically reload the disc
and stop.
CD text and MP3 title display
E00725000399
This CD player can display CD text and MP3 titles including ID3 tag information. CD text The CD player can display di
sc and track titles for discs
encoded with disc and track title information. Press the DISP button (3) repeatedly to make selections in the followingsequence: disc name
→ track name
→ normal display mode.
NOTE●
The display can show up to 16
characters. If a disc name
or track name has more than 16 characters, press thePAGE button (10) to view
the next 16 characters.
●
When there is no title information to be displayed, the dis- play shows “NO TITLE”.
●
Characters that the CD player
cannot display are shown as
“ ”.
Example Disc name Track name
BK-BK2008E1ENUK.en-uk-Section8.fm Page
41 Wednesday, January 9, 2008 4:41 PM

For pleasant driving
5-61
5
To listen to a CD
E00709601075
The CD can be loaded or ejected
by pressing the LOAD button
(15) or the eject button (7) even
if the audio system power is
off. 1. Press the PWR button (2) to turn the audio system on and
off. The system turns on in the last mode used.
2. Press the CD button (4) to enter CD mode. The auto-
changer will start playback if
the CD is already in the
autochanger.
3. To stop the CD, turn off the power by pressing the PWR
button (2) or change over to radio mode by pressing theAM/FM button (1), or eject th
e disc by pressing the eject
button (7).
NOTE●
To adjust the volume and tone, refer to “To adjust the vol- ume” on page 5-44 and “To adjust the tone” on page 5-44.
●
As many as 6 CDs can be inserted into the CD auto- changer.
●
For information concerning
the handling of the compact
discs, refer to “Handling of compact discs” on page 5-74.
To s e t d i s c sTo set a single disc 1. Press the LOAD button (15) briefly. 2. The autochanger will show “WAIT” on the display and
start making itself ready for disc loading.
3. When the autochanger is read
y for disc loading, the indi-
cator light (A) will come on and the display will show “LOAD DISC (1~6)”.
4. Insert a disc into the disc loading slot.NOTE●
If there are multiple empty slots, you can select your desired slot by pressing the
DISC buttons (16 or 17).
●
If you do not insert a disc for about 15 seconds after the autochanger starts standing
by for loading, the loading
standby mode w
ill be canceled.
BK-BK2008E1ENUK.en-uk-Section8.fm Page
61 Wednesday, January 9, 2008 4:41 PM