2008 MITSUBISHI SHOGUN bulb

Maintenance
8-39
8
2. Depress the tab (B) on the harness connector and pull the
harness connector (C) to remove it.
3. To install the bulb, perform the removal steps in reverse.
Replacement of low beam1. Remove the bulb and connector assembly (A) by turning
it anticlockwise.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
39 Wednesday, January 9, 2008 4:50 PM

8-40 Maintenance
8
2. Depress the tab (B) on the harness connector and pull the
harness connector (C) to remove it.
3. To install the bulb, perform the removal steps in reverse.
CAUTION
!●
Handle halogen lamp bulbs with care. The gas inside halogen lamp bulbs is highly pressurized, so drop-ping, knocking, or scratching a halogen lamp bulb can cause it to shatter.
●
Never hold the halogen lamp
bulb with a bare hand,
dirty glove, etc. The oil from your hand could cause the bulb to break the next time th
e headlamps are operated.
If the glass surface is dirt
y, it must be cleaned with
alcohol, paint thinner, etc., and refit it after drying it thoroughly.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
40 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-41
8
Position lamps
E01003700471
1. Turn the bulb socket an
ticlockwise to remove it.
2. Remove the bulb from the socket by pulling out. 3. To install the bulb, perform the removal steps in reverse.
Front turn-signal lamps
E01003800414
1. Turn the bulb socket anticlockwise to remove it. 2. Remove the bulb from the socket by pulling out 3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
41 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-43
8
3. Remove the entire socket and bulb assembly (G) by turn-
ing it anticlockwise.
4. To install the bulb, perform the removal steps in reverse.
CAUTION
!●
Handle halogen lamp bulbs with care. The gas inside halogen lamp bulbs is highly pressurized, so drop-ping, knocking, or scratc
hing a halogen lamp bulb
can cause it to shatter.
●
Never hold the halogen lamp bulb with a bare hand, dirty glove, etc. The oil from your hand could cause the bulb to break the next time the fog lamps are used.If the glass surface is dirt
y, it must be cleaned with
alcohol, paint thinner, etc., and refit it after drying thoroughly.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
43 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-45
8
3. Remove the socket and bulb assemblies by turning it anti-
clockwise. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.
Right side
A- Rear turn-signal lamp* B- Stop and tail lamp*
Stop lamp*
C- Reversing lamp 3-door models 5-door models
BK-BK2008E1ENUK.en-uk-Section11.fm Page
45 Wednesday, January 9, 2008 4:50 PM

8-46 Maintenance
8
On bumper
*
1. Remove the lens mounting screws.
2. Remove the socket and bulb assembly together by turning
it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal steps in reverse.D- Rear turn-signal lamp E- Tail lamp
BK-BK2008E1ENUK.en-uk-Section11.fm Page
46 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-47
8
Rear fog lamp
E01004100241
1. Open the spare wheel garnis
h (A). (Refer to “To remove
the spare tyre” on page 6-18.)
2. Remove the socket and bulb assembly (B) by turning it
anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
47 Wednesday, January 9, 2008 4:50 PM

8-48 Maintenance
8
High-mounted stop lamp
E01004500362
1. Insert the tip of a blade (or
minus) screwdriver at the edge
of the cover and pry gently to remove the cover.
2. Remove the socket and bulb assembly together by turning
it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
48 Wednesday, January 9, 2008 4:50 PM