2008 MITSUBISHI SHOGUN service reset

3-2 Instruments and controls
3
Instruments
E00500100241
Tachometer
E00500300458
The tachometer indicates the
engine speed (r/min). The
tachometer helps you to obtain more economical driving and also warns you of excessive engine speeds (Red zone).
1- Speedometer (km/h or mph + km/h) 2- Tachometer 3- Tripmeter reset button/Daytime dipper button 4- Fuel gauge5- Odometer/Tripmeter/Service reminder 6- Water temperature gauge
CAUTION
!●
When driving, watch the
tachometer to make sure
that the engine speed indi
cation does not rise into
the red zone (excessive engine rpm).
BK-BK2008E1ENUK.en-uk-Section6.fm Page 2 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-3
3
Odometer/Tripmeter/Service reminder
E00500600998
With the ignition switch in the “ON” position, odometer, tripm- eter, and service reminder indications are given.
Odometer The odometer indicates the tota
l distance the vehicle has trav-
elled.TripmeterThe tripmeter indicates the dist
ance travelled during a particu-
lar trip or period. There are two tripmeter displays: TRIP and . TRIP can be used to measur
e the distance travelled since
the current trip began. At the same time, TRIP can be used to measure the dist
ance from an inte
rmediate location.
To switch the display between TRIP and TRIP , press the reset button (B) less than 1 second.
A- Odometer/Tripmeter/Service reminder B- Reset button
TRIP ODOService reminder TRIP ODO
BK-BK2008E1ENUK.en-uk-Section6.fm Page 3 Wednesday, January 9, 2008 4:32 PM

3-4 Instruments and controls
3
NOTE●
If you do not push the button for about 10 seconds while the service reminder is showing, the display will return to the odometer indication.
●
The odometer, tripmeter, an
d service reminder indications
are given for 30 seconds after the ignition switch has been turned to the “ACC” or “LOCK” position.
●
After the odometer, tripmeter, and service reminder indi- cations have gone off, they come back on for about 30 seconds if either of the fo
llowing actions takes place.
• The driver’s door is opened.• The reset button is pressed.
To reset the tripmeter To return the display to “0”, press the reset button (B) for morethan 2 second. Only the currently displayed value will be reset.NOTE●
When disconnecting the battery
terminal for a long time,
the memory of tripmeter display TRIP and are cleared, and the display returns to “0”.
Service reminder
E00517700092
The service reminder shows the number of months (1) anddriving distance (3) remaining until the next 12-monthly(15,000 km or 9,000 miles) inspection. When the next inspec- tion is nearly due, the display s
hows “-----”. At this time, a
spanner mark (2) is shown for a few seconds whenever theignition switch is turned from the “OFF” position to the “ON” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 4 Wednesday, January 9, 2008 4:32 PM

3-6 Instruments and controls
3
Resetting the service reminder With the ignition switch in the “OFF” position, it is possible to reset the spanner mark (A) and “-----” indication (B). When they have been reset, the number of months and driving dis-tance remaining until the next inspection are shown and the spanner mark (A) is no longer shown every time the ignition switch is turned from the “OFF
” position to the “ON” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 6 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-7
3
1. Push the reset button (D) to view the number of months
and driving distance remaining until the next inspection.
2. Give the reset button (D) a long push (at least two sec-
onds) to make the spanner mark (A) start flashing. (If youdo not touch the reset button for 10 seconds while the spanner mark is flashing, the display will revert to its orig- inal indication.)
3. Give the reset button (D) a gentle push while the spanner
mark is flashing. The “-----” indication (B) will change to “cLEAr” (C).
4. The number of months and driving distance remaining
until the next inspection will be shown.
NOTE●
It is not possible to reset the “-----” indication (B) with the ignition switch in the “ON” position.
●
When a certain distance has
been driven and a certain
period has elapsed after app
earance of the “-----” indica-
tion (B), the indication is automatically reset and the number of months until the next periodic inspection isshown.
●
If you accidentally reset th
e display, consult a MITSU-
BISHI MOTORS Author
ized Service Point.
Fuel gauge
E00500700638
The fuel gauge indicates the fuel
level in the fuel tank when the
ignition switch is in the “ON” position.
CAUTION
!●
Daily and periodic inspect
ions and maintenance are
your responsibility. Be sure to perform them to help prevent accidents and breakdowns.
F- Full E- Empty
CAUTION
!●
For petrol-powered vehicles, do not drive with an extremely low fuel level;
running out of fuel could
cause damage to the catalytic converter.
●
For diesel-powered vehicl
es, do not drive with an
extremely low fuel level;
running out of fuel could
cause damage to the fuel system.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 7 Wednesday, January 9, 2008 4:32 PM

5-28 For pleasant driving
5
RDS uses PI (program identification) signal and AF (alterna- tive frequency) list transmitted in addition to the normal FM broadcasting programs, and picks
up the FM stations that are
transmitting the same program from the AF list and automati-cally tunes to the station with the strongest signal intensity. Therefore, you can co
ntinue listening to one program in, for
example, a long dist
ance driving without retuning to the other
station transmitting the same
program when you are leaving
the service area of the cu
rrently receiving station.
The RDS radio also features th
e limited reception of the pro-
gram types, the break-in reception of the traffic announcement to the EON (enhanced other network) and emergency broad- cast, and the limited/
unlimited reception of
the regional pro-
grams.AF (Alternative Frequencies) function
E00720900090
The AF function finds a station broadcasting the same programand selects the station with the strongest signal of AF lists. The AF function is turned on at all times unless you manually switch it off. The AF function can be turned ON and OFF. Refer to “Adjusting the time” on page 3-19.CT (Clock Time) function
E00721000085
The clock can be set automatically
by using the signal from the
local RDS stations. Refer to “Adjusting the time” on page
3-19
.
REG (Regional) function
E00721100028
REG function limits to receive the stations broadcastingregional programs. Regional programming and regional networks are organizeddifferently depending on the country or area (they may be changed according to the hour, st
ate, or broadcast area), so if
you don’t want to receive the re
gional programs automatically,
you can set up REG ON not to
receive regional programs.
The REG function can be
turned ON and OFF.
Refer to “Function setup mode” on page 5-33.PI (Program Identification) search function
E00721200133
When travelling long distance a
nd the recalled preset station is
weak, the radio searches anot
her frequency broadcasting the
same programming with the same PI code in AF list. If there are no frequencies br
oadcasting the same program-
ming, the radio searches a frequency broadcasting the regionalprogramming. The radio succeeds in searching the regional programming, then the display shows the REG indicator (13). If the radio does not succeed
in searching the regional pro-
gramming, the radio returns to
the recalled preset station.
The PI function can be turned ON and OFF on some vehicles. Refer to “Function setup mode” on page 5-33.NOTE●
While searching, the audio sy
stem is muted. The display
shows “WAIT” or “SEARCH”.
BK-BK2008E1ENUK.en-uk-Section8.fm Page
28 Wednesday, January 9, 2008 4:41 PM

For pleasant driving
5-53
5
RDS uses PI (program identifi
cation) signal and AF (alterna-
tive frequency) list transmi
tted in addition to the normal FM
broadcasting programs, and picks up the FM stations that are transmitting the same program from the AF list and automati-cally tunes to the station with the strongest signal intensity. Therefore, you can continue listening to one program in, for example, a long distance driving without retuning to the otherstation transmitting the same
program when you are leaving
the service area of the cu
rrently receiving station.
The RDS radio also features th
e limited reception of the pro-
gram types, the break-in receptio
n of the traffic announcement
to the EON (enhanced other network) and emergency broad- cast, and the limite
d/unlimited recep
tion of the regional pro-
grams.AF (Alternative Frequencies) function
E00720900104
The AF function finds a statio
n broadcasting the same program
and selects the station with th
e strongest signal of AF lists.
The AF function is turned on at all times unless you manually switch it off. The AF function can be turned ON and OFF. Refer to “Function setup mode” on page 5-57.CT (Clock Time) function
E00721000098
The clock can be set automatically by using the signal from thelocal RDS stations. Refer to
“Adjusting the time” on page
3-19
.
REG (Regional) function
E00721100015
REG function limits
to receive the stations broadcasting
regional programs. Regional programming and regional networks are organizeddifferently depending on the country or area (they may be changed according to the hour, state, or broadcast area), so if you don’t want to receive the re
gional programs automatically,
you can set up REG ON not to
receive regional programs.
The REG function can be turned ON and OFF. Refer to “Function setup mode” on page 5-57.PI (Program Identification) search function
E00721200146
When travelling long distance an
d the recalled preset station is
weak, the radio searches another frequency broadcasting the same programming with the same PI code in AF list. If there are no frequencies broadcasting the same program- ming, the radio searches a frequ
ency broadcasting the regional
programming. The radio succeeds
in searching the regional
programming, then the display shows the REG indicator (13). If the radio does not succeed
in searching the regional pro-
gramming, the radio returns to
the recalled preset station.
The PI function can be turned ON and OFF on some vehicles. Refer to “Function setup mode” on page 5-57.NOTE●
While searching, the audio sy
stem is muted. The display
shows “WAIT” or “SEARCH”.
BK-BK2008E1ENUK.en-uk-Section8.fm Page
53 Wednesday, January 9, 2008 4:41 PM