2008 MITSUBISHI COLT Owner's Manual (in English)

Starting and driving4-11
4
However, the outer side of the boundary line provides a wider
vision than an ordinary door mirror.
To adjust the mirror positionE00601000147
Manual remote-controlled ou tside rear-view mirrors*
Adjust the mirror position by operating the lever as indicated
by the arrows.
WARNING!
●The sense of distance that you get from an object
you see on the inner side of the mirror boundary line
differs from the sense of distance that you get from
an object you see on the outer side.
An object you see on the outer side of the boundary
line of the mirror will lo ok farther away than actu-
ally is (farther away than if you see in a normal flat
mirror) as compared with an object you see on the
inner side.
WARNING!
● Do not attempt to adjust the rear-view mirrors while
driving. This can be dangerous.
Always adjust the mirrors before driving.
●Your vehicle is equipped with convex type mirrors.
Please take into considerati on. Objects you see in the
mirror will look smaller and further away compared
to a normal flat mirror.
Do not use this mirror to estimate distance of follow-
ing vehicles when changing lanes.
1- Up
2- Down
3- Right
4- Left

4-12 Starting and driving
4
Electric remote-controlled outside rear-view mirrors*E00610900041
The electric remote-controlled out side rear-view mirrors can be
operated when the ignition switch is in the “ON” or “ACC”
position.
1. Turn the switch to the same side as the mirror whose adjustment is desired.
NOTE● After adjustment, return the switch to centre position. 2. Adjust the mirror by moving the switch left, right, up or
down.
L- Left outside mirror adjustment
R- Right outside mirror adjustment
1- Up
2- Down
3- Right
4- Left

Starting and driving4-13
4
To fold the mirrorE00601100454
The outside mirror can be folded in towards the side window to
prevent damage when parking in narrow areas.
Heated mirror*E00601200279
When the rear window demister switch is pressed, the outside
rear-view mirrors are demisted or defrosted. Current will flow
through the heater element insi de the mirrors, thus clearing
away frost or condensation.
The indicator lamp (A) will illuminate while the demister is on.
The heater will be turned off automatically in about 20 min-
utes.

4-14 Starting and driving
4Ignition switch
E00601401164
LOCK
The engine is stopped and the
steering wheel locked. The key
can only be inserted and removed when the switch is in this
position.
ACC
The engine is stopped, but th e radio, accessory socket and
other electrical devices can be operated.
ON
The engine is running, and all the vehicle’s electrical devices
can be operated.
START
The starter motor operates. After the engine has started, release
the key and it will automatically return to the “ON” position.
NOTE● For vehicles equipped with the Daytime Running Lamp,
when the ignition switch is in the “ON” position, the
headlamp low beams etc. are turned on.
Refer to “Headlamps” on page 3-31.
● Your vehicle is equipped with an electronic immobilizer,
to start the engine, the ID code which the transponder
inside the key sends must match the one registered to the
immobilizer computer. (Refer to page 1-3.)
To remove the key
When removing the key, turn the key to the “LOCK” position
and remove it.

Starting and driving4-15
4
Steering wheel lock
E00601500445
To l o c k
Remove the key at the “LOCK” position.
Turn the steering wheel until it is locked.
To unlock
Turn the key to the “ACC” position while moving the steering
wheel slightly.
CAUTION!
●
Do not remove the ignition key from the ignition
switch while driving. The steering wheel will locked,
causing loss of control.
●If the engine is stopped while driving, the brake ser-
vomechanism will cease to function and braking
efficiency will deteriorat e. Also, the power steering
system will not function and it will require greater
manual effort to operate the steering.
● Do not leave the key in the “ON” position for a long
time when the engine is no t running, as doing so will
cause the battery to be discharged.
●Do not turn the key to the “START” position when
the engine is running, as doing so could damage the
starter motor.
CAUTION!
●Remove the key when leaving the vehicle.

4-16 Starting and driving
4
NOTE●If the front wheels are turned , the anti-theft lock may
sometimes make it difficult to turn the key from “LOCK”
to “ACC”. Firmly turn the steer ing wheel to the left or to
the right as you turn the key.Starting
E00601600707
Tips for starting
● Do not operate the starter motor continuously for anything
longer than 10 seconds; doing so could run down the bat-
tery. If the engine does not start, turn the ignition switch
back to “LOCK”, wait a few seconds, and then try again.
Trying repeatedly with the starter motor still turning will
damage the starter mechanism.
● If the engine cannot be starte d because the battery is weak
or dead, refer to the “Emergency starting” section for
instructions on starting the engine.
● The engine is well warmed up with the engine speed
decreases. Extended warming-up will result in excessive
fuel consumption.
WARNING!
● Never run the engine in a cl osed or poorly ventilated
area any longer than is necessary to move your vehi-
cle in or out of the area. Carbon monoxide gases are
odourless and can be fatal.

Starting and driving4-17
4
Starting the engine (petrol-powered vehicles)E00601701255
This vehicles is equipped with an electronically controlled fuel
injection system which is automa tically controlled. When start-
ing the engine, do not de press the accelerator pedal.
The starting procedure is as follows:
Vehicles with manual transmission 1. Insert the ignition key and fasten the seat belt.
2. Make sure the parking brake is applied.
3. Depress and hold the brake pedal.
4. Fully depress the clutch pedal.
5. Place the gearshift lever in the “N” (Neutral) position.
CAUTION!
●Never attempt to start the engine by pushing or pull-
ing the vehicle. This can be very dangerous.
●Do not run the engine at high rpm or drive the vehi-
cle at high speed until th e engine has had a chance to
warm up.
● Release the ignition key as soon as the engine starts
to avoid damaging the starter motor.
●If your vehicle is equipped with a turbocharger, do
not stop the engine immedi ately after high-speed or
uphill driving. First allow the engine to idle to give
the turbocharger a chance to cool down.

4-18 Starting and driving
4
6. Turn the ignition key to the “ON” position and make cer-tain that all warning lamps are functioning properly before
starting the engine.
7. Turn the ignition key to the “START” position without depressing the accelerator pedal, and release it when the
engine starts.
NOTE● A ticking noise may be heard after starting the engine.
This is not an abnormal condition. The noise will disap-
pear after a short time of engine running.
If the ticking noise continues after the engine has warmed
up, we recommend that you have your vehicle checked.
● If the engine won’t start, depress the accelerator pedal
fully while cranking the engi ne. Once the engine starts,
release the accelerator pedal. Vehicles with automated manual transmission
1. Insert the ignition key and fasten the seat belt.
2. Make sure the parking brake is applied.
3. Depress and hold the brake pedal.
4. Turn the ignition key to the “ON” position and make cer- tain that all warning lamps are functioning properly.
5. Place the allshift lever in the “N” (Neutral) position and confirm that “N” is shown by the allshift indicator display.
Refer to “Moving the allshift lever” on page 4-27.
CAUTION!
● When starting the engine, make sure you depress
the brake pedal. If you st art the engine with the
accelerator pedal depressed, move your foot to the
brake pedal as soon as the engine has started.