2008 MERCEDES-BENZ C-Class Page 35

86 Telephone
Activating the mobile phone
Prerequisites for the mobile phone
For making calls using COMAND via the
Bluetooth
® interface, you will need a Blue-
tooth-enabled mobile phone.
i Not all mobile phones available on the mar-
ket are comparably suitable. Further information
on suitable mobile phones and connecting Blue-
tooth-enabled mobile phones to COMAND is
available via the Internet at www.mbusa.com.
Activating Bluetooth®
Before you begin activation of your mobile
phone connection via the Bluetooth® inter-
face please ensure it is compatible with
Bluetooth
® handsfree profile 1.0
(
mobile phone operating guide)
Switch on the mobile phone and enter
the PIN, if applicable (
mobile phone
operating guide).
Activate Bluetooth® connection on the
mobile phone (
mobile phone operat-
ing guide).
i On certain mobile phones, not only do you
have to activate the Bluetooth® function but the
device must also be made “visible” for other de-
vices.
Each Bluetooth
® device has a Bluetooth® device
name. It is recommended to give the device a
personal name, by which you can clearly recog-
nize your mobile phone.
i If the Bluetooth function on the
COMAND is switched off, the message “Blue-
tooth not activated in system settings.” appears.
Activate Bluetooth® connection on
COMAND (
page 169).
Registering a mobile phone
(authorizing)
When you use your mobile phone in con-
junction with COMAND for the first time,
you must register (authorize) it.
It is possible to register several mobile
phones. The connection is always estab-
lished to the mobile phone that was acti-
vated last. When you authorize a new
mobile phone, it is activated automatically.
You can switch between the authorized
mobile phones (
page 88).Searching for a mobile phone
In the phone submenu select “Phone”
K “Phone List” K “Update”.
COMAND searches for suitable Blue-
tooth
® phones within range and enters
them in the phone list.
i The duration of the search procedure de-
pends on the number and type of Bluetooth®
phones. The search may take a few minutes.
When first entering the device list and be-
fore running an update, the black
dotRindicates the active phone (found
and authorized).
After running an update:
Phone icons 3 indicate if a phone is found
(black) or not (grey).
Activating the mobile phone
Mobile phone with Bluetooth® inter-
face

87 Telephone
Activating the mobile phone
The check marks 1 indicate if a phone
has been authorized (black) or not (grey).
If a phone is not in the vehicle but has been
authorized previously, the phone symbol
and the check mark are grey 2.
i If the device list already contains ten autho-
rized devices, you must de-authorize one of the
authorized devices (
page 88). You will then
have to switch this device off and start the
search again. Otherwise the new device you are
looking for will not appear in the list.
To start search again:
Select “Update”.
Entering passcode
Select the as yet unauthorized device
(no check mark yet) from the list.
Select “Options” K “Authorize” or
Press n.
The input menu for the passcode ap-
pears.
i The passcode is any number chosen by you
between one and sixteen digits in length. We rec-
ommend to use at least four digits because this
improves the quality of the encryption during
connection. The passcode can differ during each
authorization for each device. You must enter
the same number on COMAND and on the device
to be authorized. Please also refer to the instruc-
tions in the mobile phone operating guide.
To enter from COMAND: Select the
digits in the menu bar one after the oth-
er.
To correct entry: Select õ.
To cancel entry: Select “Back”.
To confirm entry: Select B.If a Bluetooth
® connection is established
successfully, you will be prompted to enter
a code on the mobile phone (
mobile
phone operating guide).
Enter the same passcode on the mobile
phone as you did on COMAND.
The device is authorized. You can now
make calls via COMAND’s hands-free
device using the authorized
mobile phone.
External authorization
If COMAND cannot find your mobile phone,
this may be due to special security settings
on your mobile phone. In this case, you can
check whether, conversely, your mobile
phone can find COMAND.


88 Telephone
Activating the mobile phone
COMAND’s Bluetooth® device name is
“MB Bluetooth”.
In the phone submenu select “Phone”
K “Phone List” K “Update” K
“Options”
K “External Authorization”.
Start Bluetooth® search procedure on
the mobile phone (
mobile phone op-
erating guide).
Select COMAND (“MB Bluetooth”) from
the device list on your mobile phone.
When prompted to do so, enter the
passcode on the mobile phone and on
COMAND.
Displaying details on a mobile phone
In the phone submenu select “Phone”
K “Phone List”.
Select the mobile phone from the list.
Select “Options” K “Details”.
The details screen for the device is dis-
played.
To close details screen: Rotate ymz,
slide qmr or omp or press n.Deregistering (de-authorizing) a mobile
phone
In the phone submenu select “Phone”
K “Phone List”.
Select the authorized mobile phone.
Select “Options” K “De-Authorize”.
You will be asked whether the device
should really be de-authorized.
Select “Yes” or “No”.
If you select “Yes”, the authorization of
the device is withdrawn.
i If the authorization of a device, which had
been authorized in the past, has been withdrawn
and it is no longer found in the search, the device
list no longer includes this device.
Activating another mobile phone
If you have authorized several mobile
phones, you can switch between the indi-
vidual mobile phones.
When you authorize a new mobile phone, it
is activated automatically. Only one mobile
phone is active at a time.
Select “Phone” K “Phone List”.
Select the mobile phone from the list.
Press n.
The selected mobile phone is activated
if the selected mobile is within recep-
tion range and its Bluetooth
® function
is switched on. Any previously activat-
ed phone is deactivated.
Receiving business cards
You can import business cards (vCards)
into the address book from external Blue-
tooth
® devices. Please note the following:

Bluetooth® must be activated
(
page 169)
i If the “Bluetooth” function on the
COMAND is switched off, the message “Blue-
tooth not activated in system settings.” appears.

89 Telephone
Activating the mobile phone

The external device can send vCards
via Bluetooth®.

The external device in the vehicle is
switched on and authorized
(
page 86).
If the phone main menu is displayed se-
lect “Phone”
K “Receive Business
Cards”.
or
If the address book is displayed, select
“Address Book”
K “Receive Business
Cards”.
To import: Start the data transfer on
the external device (
operating guide
for the relevant device).
The COMAND imports the data for the
business cards and displays the num-
ber of business cards received.
To end reception: Press n.
or
Press the í button.
i You can also receive business cards via the
PCMCIA memory card. To do this, the business
cards must be stored in the main directory of the
PCMCIA memory card. Load PCMCIA memory
card (
page 110).
i These settings should normally not be
changed as the factory settings are matched to
most mobile phones.
i Changes may result in significant impair-
ments to the transmission quality. These set-
tings may not be changed during an active phone
call.
In the phone submenu select “Phone”
K “Phone List”.
Select an authorized mobile phone
from the list.
Select “Options” K “Reception Volu-
me” or “Transmission Volume”.
i Reception volume and Transmission only ap-
pear for authorized devices.
1Volume bar
To set the volume: Rotate ymz or
slide qmr.
The volume bar moves up or down.
To confirm selection: Press n or
slide om.
Setting transmit and receive volume

90 Telephone
Activating the mobile phone
The following conditions must be met for a
“911” emergency call:

Phone switched on

Mobile phone network available

Valid SIM card in the phone
(not required on all mobile phone net-
works)

Mobile phone connected with
COMAND via Bluetooth®
If you are unable to make an emergency
call, you will have to initiate rescue mea-
sures yourself.
The “911” emergency number is a public
service. Any abuse is punishable by law.
Enter the digits on the COMAND con-
trol unit (
page 101).
Press thew button.
The phone establishes the connection.
Wait until the emergency call centre
answers, then describe the emergency.
“911” emergency call
G Warning
The 911 emergency call system is a public
service. Using it without due cause is a
criminal offense.

92 Telephone
Submenu overview
Switching to phone mode
Press the function button Y on the
COMAND control unit.
i If you press thew button with the phone
main menu already open, the call list “Calls Di-
aled” appears (
page 97).
or
From another main function
Select “Phone” K “Phone” K
“Phone”.
i If phone mode was active last, you only need
to select “Phone”.
Within the phone function
Select “Phone” K “Phone”.
or
In the phone mode press the í but-
ton repeatedly until the phone main
menu appears.1Phone service status
2Signal strength (if provided by phone)
3Call status
4Displays COMAND phone book
5Displays call list selection
6Speller with characters for entering
phone numbers
7Device name of the connected mobile
phone
Phone main menu

93 Telephone
COMAND phone book
The COMAND phone book is an extract of
entries from the COMAND address book.
All the COMAND address book entries hav-
ing at least one phone number can be
found in the COMAND phone book.
i For many operating functions you can also
use the buttons on the multifunction steering
wheel, e.g. the (, &, $, %,
#,
s
or t buttons, for selecting a track or a
menu, scrolling through lists or initiating or end-
ing a call (
page 23).
Open the phone main menu
(
page 92).
Select “Name”.
The COMAND phone book is displayed.
COMAND phone book with search speller
1Address book entry
2Calls up options
3Search speller
4Closes phone book
5m symbol for voice tag
Address book entries may have the symbol
5. An additional voice tag is saved with
these entries.
If an address book entry has the symbol
+ then this has more than one phone
number. You can select these subentries
(
page 93).
To close phone book: In the search
speller select the symbol “Back”.
or
Press í.
Selecting via list
Rotate ymz or slide qmr until the de-
sired entry is highlighted.
Selecting subentries
Select an address book entry with the
symbol + from the list and press n.
The symbol + changes into / and
the subentries appear.
1Expanded phone book entry
2Phone book entry with subentries
Rotate ymz or slide qmr until the de-
sired subentry is highlighted.
COMAND phone book
Opening COMAND phone book
Selecting an entry

94 Telephone
COMAND phone book
Displaying details on an entry
COMAND can also fully display an abbrevi-
ated entry.
Select entry.
Select “Options” K “Details”.
The details screen appears.
To close details screen: Slide omp
repeatedly until the entry is highlighted
again.
Select entry (page 93).
Press n.
or
Press thew button on the COMAND
control unit.
If the entry contains subentries, a list
appears.
Select the desired subentry.
Press n again.
or
Press thew button on the
COMAND control unit.
i When a new entry is added through the
COMAND phone book, it is saved to the address
book.
Select “Options” K “New Entry” in the
COMAND phone book.
Select a number category, e. g.
“Home”.
Select a phone category, e. g.
“Mobile Phone”.
Select “Save”.
The input menu with the data fields ap-
pears.
1Cursor
2Data field
3Predictive speller
4Selected phone category
Switching data field
Slide mq until the predictive speller is
not highlighted.
Then slide qmr to select desired field
and press n.
or
Select [ or ] in the speller.
The input menu indicates the selected
data field.
Initiating call to an entry
Creating a new entry