2008 Lancia Musa engine

178
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
Using the battery when the
fluid is too low can dam-
age it irreparably and generate a
risk of explosion.
WARNING
CHANGING THE BATTERY
If required, replace the battery with a
genuine spare part having the same
specifications.
If a battery with different specifica-
tions is fitted, the service intervals
given in the “Service schedule” in this
section will no longer be valid.
Refer therefore to the instructions pro-
vided by the battery manufacturer.Batteries contain sub-
stances that can be very
dangerous for the environ-
ment. t is advisable to have
the battery changed by a Lancia
Dealership where it will be disposed
of according to the law.Incorrect assembly of elec-
tric and electronic devices
may cause severe damage
to your car. Go to a Lancia
Dealership if you want to install ac-
cessories (alarms, mobile phone,
etc.): they will suggest the most suit-
able devices and advise you if a
higher capacity battery needs to be
installed.USEFUL ADVICE FOR
LENGTHENING THE LIFE OF
YOUR BATTERY
To avoid draining your battery and to
lengthen its life, observe the following
indications:
❒when you park your car, ensure
that doors, bonnet and flaps are
well closed in order to ensure that
no lights remain on inside the pas-
senger compartment;
❒switch off all lights inside the car:
the car is however equipped with
a system which switches all inter-
nal lights off automatically;
❒when the engine is off, do not keep
devices running for long periods
(e.g. sound system, hazard lights
etc.);
❒before performing any operation
on the electrical system, discon-
nect the battery negative terminal
cable;
❒screw the terminals of the battery
down hard.
If the vehicle must remain
unused for a long time at
very low temperatures, remove the
battery and carry it to a warm
place, to avoid freezing.
WARNING
When performing any op-
erations on the battery or
near it, always protect your eyes
with the special goggles.
WARNING
165-186 MUSA 3ed GB 12-11-2007 11:39 Pagina 178

184
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
To correctly wash the car:
❒remove the aerial from the roof to
prevent damage to it if the car is
washed in an automatic system;
❒wash the body using a low pres-
sure jet of water;
❒wipe a sponge with a slightly
soapy solution over the bodywork,
frequently rinsing the sponge;
❒rinse well with water and dry with
a jet of air or a chamois leather.
Dry the less visible parts particularly
carefully, such as the door frames,
bonnet and the headlight frames,
where water may stagnate more eas-
ily. It is a good idea to leave the car in
the open for a while after washing it
to give time for the water to evapo-
rate.
Do not wash the car after it has been
parked in the sun or when the engine
is bonnet is hot: this can alter the
gloss of the paint.Exterior plastic parts must be cleaned
in the same way as the rest of the car.
Where possible, do not park under
trees; the resinous substance many
species release give the paint a dull
appearance and increase the possibil-
ity of triggering rust processes.
IMPORTANT Bird droppings must be
washed off immediately and thor-
oughly as the acid they contain is par-
ticularly aggressive.Windows
Use specific window cleaner products.
Use also clean cloths to avoid scratch-
ing the glass or damaging the trans-
parency.
IMPORTANT The inside of the rear
window should be wiped gently with
a cloth in the direction of the fila-
ments to avoid damaging the heating
device.
Front headlights
IMPORTANT Never use aromatic
substances (e.g.: petrol) or ketenes
(e.g.: acetone) for cleaning front
headlight plastic lens.Detergents cause water pol-
lution. The car should be
washed in areas equipped
for collecting and purifying
the liquid used in the washing
process.
165-186 MUSA 3ed GB 12-11-2007 11:39 Pagina 184

185
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
Engine compartment
At the end of the winter the engine
compartment should be carefully
washed, without directing the jet
against electronic control units. Have
this operation performed at a spe-
cialised workshop.
IMPORTANT Perform this operation
on a cold engine and with the key at
STOP. After the washing operation,
make sure that the various protections
(e.g. rubber caps and guards) have
not been removed or damaged.
Never use flammable
products, such as petrol
ether or rectified petrol to clean in-
side the car. The electrostatic
charges which are generated by
rubbing during the cleaning oper-
ation may cause a fire.
WARNINGINTERIORS
Periodically check that water is not
trapped under the mats (due to water
dripping off shoes, umbrellas, etc.)
which could cause oxidisation of the
sheet metal.
CLEANING SEATS AND
FABRIC PARTS
Remove dust with a soft brush or a
vacuum cleaner. It is advisable to use
a moist brush on velvet upholstery.
Rub the seats with a sponge moist-
ened with a solution of water and
neutral detergent.
INTERIOR PLASTIC PARTS
It is advisable to clean interior parts
with a moist cloth and a solution of
water and mild soap. Use specific
products for cleaning plastic, without
solvents and specifically designed to
prevent damage to the appearance
and colour of the treated parts to re-
move grease and tough stains.
IMPORTANT Never use spirit or
petroL to clean the glass of the in-
strument panel or other plastic parts.
165-186 MUSA 3ed GB 12-11-2007 11:39 Pagina 185

187
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
TECHNICAL SPECIFICATIONS
IDENTIFICATION DATA .................................. 188
ENGINE CODES -
BODYWORK VERSIONS .................................. 190
ENGINE........................................................... 191
FUEL FEED/IGNITION ................................... 192
TRANSMISSION............................................... 192
BRAKES........................................................... 193
SUSPENSIONS................................................. 193
STEERING....................................................... 193
WHEELS.......................................................... 194
DIMENSIONS................................................... 198
PERFORMANCE.............................................. 199
WEIGHTS........................................................ 200
CAPACITIES .................................................... 201
FLUIDS AND LUBRICANTS ............................ 202
FUEL CONSUMPTION .................................... 204
CO
2EMISSIONS............................................... 205
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 187

188
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
IDENTIFICATION
DATA
Take note of the identification codes.
The identification data stamped on
the platesfig. 1and their respective
positions are as follows:
1- Model plate.
2- Chassis marking
3- Bodywork paint identification
plate
4- Engine marking.MODEL PLATE fig. 2
This plate is applied to the engine
compartment front beam and shows
the following identification data:
B- Homologation number.
C- Vehicle type code.
D- Chassis number.
E- Maximum vehicle weight fully
loaded.
F- Maximum vehicle weight fully
loaded plus trailer.G- Maximum weight on front axle.
H- Maximum vehicle weight on rear
axle.
IEngine type.
L- Body version code.
M- Spare part code.
N- Smoke opacity index (for diesel
engines).
fig. 1L0D0450mfig. 2L0D0415m
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 188

189
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
CHASSIS MARKING fig. 3
This is printed on the passenger com-
partment floor bed near the front
right seat.
To access it, lift the opening cut in the
carpet for this purpose; it shows:
❒car model;
❒chassis number.
BODYWORK PAINT
IDENTIFICATION PLATE fig. 4
This plate is applied to the front bon-
net and shows the following data:
A- Paint manufacturer.
B- Colour name.
C- Lancia colour code.
D- Respray and touch up code.ENGINE MARKING
Engine marking is stamped on the
motor block, passenger compartment
side, and includes the model and the
chassis number.
fig. 3L0D0227m
fig. 4L0D0228m
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 189

190
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
ENGINE CODES - BODYWORK VERSIONS
Versions
1.48V(▲)
1.416V
1.3 Multijet 70HP
1.3 Multijet 90HP
1.9 Multijet
(
▲) Engine provided for some versions/markets only
(*) For specific markets
(
❒) DPF versionEngine code
350A1000
843A1000
188A9000
199A3000
188B2000Bodywork code
350AXF1A08EL
350AXA1B07DL
350AXE1A06CL (*)
350AXB1A01ML
350AXG1A09UL
350AXG1A02WL
350AXC1A02LL (
❒)
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 190

191
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
1.3 Multijet 70HP
188A9000
Diesel
4 in line
4
69.6 x 82
1248
18±0.4
51
70
4000
180
18,3
1750
–
Diesel fuel for
motor vehicles
(Specification
EN590)
1.3 Multijet 90HP
199A3000
Diesel
4 in line
4
69.6 x 82
1248
17,6±0.4
66
90
4000
200
20
1750
–
Diesel fuel for
motor vehicles
(Specification
EN590)
ENGINE
INTRODUCTION
Engine code
Cycle
Number and layout of cylinders
Number of valves per cylinder
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Maximum power (EEC) kW
HP
corresponding ratio: rpm
Maximum torque (EEC) Nm
kgm
corresponding ratio: rpm
Spark plugs
Fuel
(▲)Engine provided for some versions/markets only
1.48V(▲)
350A1000
Otto
4 in line
2
72 x 84
1368
11±0.2
57
77
6000
115
11,7
3000
NGK ZKR7A-10
Unleaded petrol
95 RON
(Specification
EN228)1.9 Multijet
188B2000
Diesel
4 in line
2
82 x 90.4
1910
18±1
74
100
4000
260
26.4
2000
–
Diesel fuel for
motor vehicles
(EN590 specifica-
tions) 1.4
16V
843A1000
Otto
4 in line
4
72 x 84
1368
11±0.2
70
95
5800
128
13
4500
NGK ZKR7A-10
Unleaded petrol
95 RON
(Specification
EN228)
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 191