2008 INFINITI FX35 relay

ACS-2
DTC 104 LASER AIMING INCMP ..........................54
DTC 107 LASER COMM FAIL ...............................54
DTC 109 LASER HIGH TEMP ...............................54
TROUBLE DIAGNOSIS FOR SYMPTOMS .......55
Symptom Chart .................................................... ...55
Symptom 1 MAIN Switch Does Not Turn ON*1,
MAIN Switch Does Not Turn OFF*2 ..................... ...55
Symptom 2 ICC System Cannot Be Set (MAIN
Switch Turns ON/OFF) ........................................ ...
56
Symptom 3 ICC System Cannot Be Operated by
CANCEL Switch, RESUME/ACCELERATE
Switch or DISTANCE Switch ..................................
56
Symptom 4 ICC System Is Not Cancelled When
the A/T Selector Lever Is in Other Than "D" and
"M" Position ............................................................
57
Symptom 5 Chime Does Not Sound .......................57
Symptom 6 Driving Force Is Hunting ......................58
Symptom 7 ICC System Frequently Cannot De-
tect the Vehicle Ahead/ Detection Zone Is Short . ...
58
Symptom 8 the System Does Not Detect the Vehi-
cle Ahead at All .......................................................
59
SELF-DIAGNOSIS BY ICC SYSTEM DISPLAY
WILL NOT RUN ......................................................
59
ELECTRICAL COMPONENT INSPECTION .....63
ICC Steering Switch ............................................. ...63
Booster Solenoid .....................................................63
Release Switch .......................................................63
ICC Brake Switch and Stop Lamp Switch ...............64
ICC Brake Hold Relay .............................................64
REMOVAL AND INSTALLATION .....................65
ICC Unit ............................................................... ...65
ICC Sensor .............................................................65
ICC Steering Switch ................................................66
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

ACS-8
< SERVICE INFORMATION >[ICC]
DESCRIPTION
DATA MONITOR INPUT ITEM LIST
DATA MONITOR OUTPUT ITEM LIST
InputData monitored
Item [unit] CAN Description
ECM THRTL OPENING
[%]
×Indicates throttle angle read by ICC unit through CAN communication (ECM transmits
throttle angle through CAN communication).
ENGINE RPM
[rpm] ×
Indicates engine speed read by ICC unit through CAN communication (ECM transmits
engine speed through CAN communication).
MAIN SW
[On/Off] ×Indicates [On/Off] status as judged from steering switch signal (ECM transmits steering
switch signal through CAN communication).
SET/COAST SW
[On/Off] ×Indicates [On/Off] status as judged from steering switch signal (ECM transmits steering
switch signal through CAN communication).
CANCEL SW
[On/Off] ×
Indicates [On/Off] status as judged from steering switch signal (ECM transmits steering
switch signal through CAN communication).
RESUME/ACC SW
[On/Off] ×Indicates [On/Off] status as judged from steering switch signal (ECM transmits steering
switch signal through CAN communication).
IDLE SW
[On/Off] ×Indicates [On/Off] status of idle switch read by ICC unit through CAN communication
(ECM transmits ON/OFF status through CAN communication).
TCM VHCL SPD AT
[km/h] or [mph]
×Indicates vehicle speed calculated from AT vehicle speed sensor by ICC unit through
CAN communication (TCM transmits AT vehicle speed sensor signal through CAN com-
munication).
GEAR
[1, 2, 3, 4, 5] ×Indicates AT gear position read by ICC unit through CAN communication (TCM transmits
gear position through CAN communication).
D RANGE SW
[On/Off] ×
Indicates [On/Off] status of “D” position read by ICC unit through CAN communication
(TCM transmits ON/OFF condition of “D” position through CAN communication).
NP RANGE SW
[On/Off] ×Indicates PNP switch signal read by ICC unit through CAN communication (TCM trans-
mits PNP switch signal through CAN communication).
ABS actuator
and electric
unit (control
unit) VHCL SPEED SE
[km/h] or [mph]
×Indicates vehicle speed calculated from wheel sensor by ICC unit through CAN commu-
nication (ABS actuator and electr
ic unit (control unit) transmits wheel speed sensor signal
through CAN communication).
BCM WIPER SW
[Off/Low/High]
×Indicates wiper [Off/Low/High] status (BCM transmits front wiper request signal through
CAN commun
ication).
Brake pres-
sure sensor PRESS SENS
[bar]
Indicates brake fluid pressure value calculated from signal voltage of pressure sensor.
Release
switch RELEASE SW NO
[On/Off]
Indicates [On/Off] status as judged from release switch signal.
ON when brake is depressed.
OFF when brake is not depressed.
RELEASE SW NC
[On/Off] Indicates [On/Off] status as judged from release switch signal.
ON when brake is not depressed.
OFF when brake is depressed.
ICC brake
switch BRAKE SW
[On/Off]
Indicates [On/Off] status as judged from ICC brake switch signal.
Sto p l am p
switchSTOP LAMP SW
[On/Off]
Indicates [On/Off] status as judged from stop lamp switch signal.
Output Data monitored
Item [unit] CAN Description
ICC warning
chime BUZZER O/P
[On/Off]
×
Indicates [On/Off] status of ICC warning chime output.
ICC brake hold
relay STP LMP DRIVE
[On/Off]
Indicates [On/Off] status of brake hold relay drive output.
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

DESCRIPTIONACS-9
< SERVICE INFORMATION > [ICC]
C
D
E
F
G H
I
J
L
M A
B
ACS
N
O P
ACTIVE TEST ITEM LIST
Component DescriptionINFOID:0000000001328807
CAN CommunicationINFOID:0000000001328808
CAN (Controller Area Network) is a serial communication li ne for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tric control units are equipped onto a vehicle, and eac h control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN COMMUNICATION UNIT
Refer to LAN-43, "CAN System Specification Chart".
Output CONSULT-III ICC
[ACTIVE TEST]
Item CAN Description
Combination
meter ICC BUZZER 1
×Able to start ICC warning chime with a driving signal from ICC unit.
METER LAMP ×Able to turn ICC system display ON with a driving signal from ICC unit.
ICC brake hold
relay STOP LAMP Able to start ICC brake hold relay with a driving signal from ICC unit.
Booster sole-
noid BOOSTER SOL/V
3
Able to start booster solenoid with a driving signal from ICC unit.
ComponentVehicle-to-
vehicle
distance
control mode Conventional
(fixed speed)
cruise
control mode Brake assis
(with preview function) Description
ICC unit ××× Operates electric throttle control actuator and brake
booster based on that sensor signals and CAN commu-
nication data, then controls vehicle distance.
ICC sensor ×× Irradiates laser beam, and receives reflected laser beam
to measure distance from preceding vehicle.
ECM ××× Transmits throttle position signal and ICC steering switch
signal to ICC unit through CAN communication.
ABS actuator and electric
unit (control unit) ××× Transmits wheel speed sensor signal to ICC unit through
CAN communication.
Brake pressure sensor ×× Detects fluid pressure in master cylinder.
Brake booster ×× Adjusts brake fluid pressure, based on command from
ICC unit.
BCM × Transmit front wiper request signal to ICC unit through
CAN communication.
TCM ×× Transmits gear position signal and output shaft revolu-
tion signal to ICC unit through CAN communication.
Unified meter and A/C amp. ××× Receives ICC system display signal, ICC warning lamp
signal and buzzer output signal from ICC unit through
CAN communication.
ICC brake switch, stop lamp
switch ××× Transmit operating signal to ICC unit when touching
brake pedal. ICC unit cancels cruise system at driver's
brake operation.
ICC brake hold relay × Receives stop lamp driving signal from ICC unit, and
turns stop lamp ON.
Parking brake switch ×× The cruise system is cancelled when applied.
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

ACS-32
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS —
GENERAL DESCRIPTION
ACTIVE TEST
CAUTION:
 Never perform the active test while driving.
 Active test cannot be started while I CC system warning indicator illuminates.
ICC BUZZER 1
 Touch “ON” and “OFF” to check that ICC warni ng chime operates as in the following chart.
METER LAMP
 Start engine.
 Touch “ON” and “OFF” to check that ICC system display operates as in the following chart.
STOP LAMP
 Touch “ON” and “OFF” to check that stop la mp operates as in the following chart.
BOOSTER SOL/V 3
 Start engine.
 Touch any of “MODE 1”, “MODE 2”, “MODE 3” to che ck that following operation condition is caused by oper-
ating monitor and brake pedal.
 “START” is displayed 10 seconds after operation start. (Active test is completed.)
Self-Diagnostic FunctionINFOID:0000000001328824
WITH CONSULT-III
NP RANGE SW
[On/Off] ×× Indicates PNP switch signal read from ICC unit through CAN
communication (TCM transmits PNP switch signal through CAN
communication).
DISTANCE ×NOTE:
This item is displayed, but cannot monitor.
RELATIVE SPD ×NOTE:
This item is displayed, but cannot monitor.
STP LMP DRIVE
[On/Off] ××
Indicates [On/Off] status of brake hold relay drive output.
TURN SIGNAL ×× NOTE:
This item is displayed, but cannot monitor.
Monitored Item [unit]
ECU INPUT
SIGNALS MAIN
SIGNALS SELECTION
FROM
MENU Description
BUZZER O/P ON OFF
Buzzer sound Beep Not activated
METER LAMP ON OFF
ICC system display Full illumination OFF
STP LMP DRIVE ON OFF
Stop lamp Lamp ON Lamp OFF
PKIA9821E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-35
< SERVICE INFORMATION > [ICC]
C
D
E
F
G H
I
J
L
M A
B
ACS
N
O P
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Diagnostic Trouble Code (DTC) ChartINFOID:0000000001328825
×: Applicable
DTC
No. CONSULT-III
screen terms ICC
system
warning lamp Fail-safe
Malfunctions detected where... Refer-
ence
page
Ve h i c l e -
to-
vehicle
distance control mode Conven-
tional
(fixed
speed) cruise
control mode Brake as-
sist (with
preview
function)
11 CONTROL UNIT ××××  ICC unit internal malfunctionACS-36
20 CAN COMM CIRCUIT ××××  ICC unit detected CAN communi-
cation malfunction. ACS-36
31 POWER SUPPLY CIR
××××  ICC unit power supply voltage is
excessively low (less than 8 V). ACS-37
34 POWER SUPPLY CIR2
××××  ICC unit power supply voltage is
excessively high (more than 19 V). ACS-37
41 VHCL SPEED SE CIRC
××××  Wheel sensor malfunction.
 ABS actuator and electric unit
(control unit) malfunction
 AT vehicle speed sensor malfunc- tion
TCM malfunction ACS-37
43 ABS/TCS/VDC CIRC
××××  VDC/TCS/ABS system malfunc-
tion ACS-38
45 BRAKE SW/STOP L SW
××××  Brake and stop lamp switch har-
ness is open or shorted.
 Brake and stop lamp switch is ON
or stuck to OFF.
 Brake and stop lamp switch is stuck to ON. ACS-38
46 OPERATION SW CIRC
×××  ICC steering switch harness or spi-
ral cable is open or shorted.
 ICC steering switch malfunction ACS-40
61 PRESS SEN CIRCUIT
×× ×  Brake pressure sensor harness is
open or shorted.
 Brake pressure sensor malfunction
 Brake pressure sensor input circuit malfunction ACS-41
62
BOOSTER SOL/V
CIRCUIT ×× ×  Solenoid harness is open or short-
ed.
 Solenoid is open.
 Solenoid drive circuit malfunction ACS-42
63 RELEASE SW CIRCUIT
××××  Release switch harness is open or
shorted.
 Release switch malfunction
 Release switch input circuit mal- function ACS-43
65 PRESSURE CONTROL
×× ×  Booster malfunctionACS-45
74 LASER BEAM OFF CNTR ×× ×  Laser beam of ICC sensor is off the
aiming point. ACS-45
90 STOP LAMP RLY FIX
×× ×  Normally open terminal of stop
lamp relay is stuck. ACS-46
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-39
< SERVICE INFORMATION > [ICC]
C
D
E
F
G H
I
J
L
M A
B
ACS
N
O P
NG-2 >> “STOP LAMP SW” NG: GO TO 5.
3.CHECK BRAKE SWITCH INSTALLATION AND ADJUSTMENT
Check brake switch for proper installation, and adjust the switch if necessary. Refer to BR-5
.
OK or NG
OK >> GO TO 4.
NG >> After adjustment, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
4.CHECK ICC BRAKE SWITCH
Check ICC brake switch. Refer to ACS-64, "
ICC Brake Switch and Stop Lamp Switch".
OK or NG
OK >> 1. Replace ICC unit. 2. Erase DTC and perform ICC syst em running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Replace ICC brake switch. 2. Erase DTC and perform ICC syst em running test. Then perform self-diagnosis of ICC system
again.
5.CHECK STOP LAMP ILLUMINATION
Check stop lamp illumination.
OK or NG
OK >> GO TO 6.
NG >> 1. Check stop lamp circuit. 2. After repairing, erase DTC and perform ICC system running test. Then perform self-diagnosisof ICC system again.
6.CHECK ICC BRAKE HOLD RELAY
1. Turn ignition switch OFF.
2. Remove ICC brake hold relay.
3. Check ICC brake hold relay. Refer to ACS-64, "
ICC Brake Hold Relay"
OK or NG
OK >> GO TO 7.
NG >> 1. Replace brake hold relay.
2. Erase DTC and perform ICC syst em running test. Then perform self-diagnosis of ICC system
again.
7.CHECK ICC BRAKE HOLD RELAY CIRCUIT
1. Disconnect ICC unit connector and stop lamp switch connector.
2. Check continuity between ICC unit harness connector and ICC brake hold relay harness connector.
3. Check continuity between ICC unit harness connector and ground.
OK or NG
OK >> GO TO 8.
NG >> 1. Repair harness between ICC unit and ICC brake hold relay. 2. Erase DTC and perform ICC syst em running test. Then perform self-diagnosis of ICC system
again.
8.CHECK STOP LAMP SWITCH CIRCUIT
ICC unit connector Terminal ICC brake hold relay
connector Terminal Continuity
M89 38 E14 7 Yes
ICC unit connector Terminal GroundContinuity
M89 38 No
PKIA9907E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

ACS-46
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS FOR
SELF-DIAGNOSTIC ITEMS
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> INSPECTION END
DTC 90 STOP LAMP RLY FIXINFOID:0000000001328838
1.CHECK CONNECTOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector, and connect it securely again.
3. Erase DTC and perform ICC system running test. T hen perform self-diagnosis of ICC system again.
Is malfunction indicated?
YES >> GO TO 2.
NO >> Poor connector connection 1. Check connector (Check connector housing for disconnected, loose, bent, and collapsed ter-minals. If any malfunction is detected, repair applicable part).
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
2.CHECK STOP LAMP SWITCH AND ICC BRAKE SWITCH
With “Data Monitor” of “ICC”, check that “S TOP LAMP SW” and “BRAKE SW” operate normally.
OK or NG
OK >> GO TO 12.
NG-1 >> “BRAKE SW” NG: GO TO 3.
NG-2 >> “STOP LAMP SW” NG: GO TO 9.
3.CHECK BRAKE SWITCH INSTALLATION AND ADJUSTMENT
Check brake switch for proper installation, and adjust the switch if necessary. Refer to BR-5, "
Inspection and
Adjustment".
OK or NG
OK >> GO TO 4.
NG >> After adjustment, erase DTC and perform ICC system running test. Then perform self-diagnosis
of ICC system again.
4.CHECK ICC BRAKE SWITCH AND STOP LAMP SWITCH
Check ICC brake switch and stop lamp switch. Refer to ACS-64, "
ICC Brake Switch and Stop Lamp Switch".
OK or NG
OK >> GO TO 5.
NG >> 1. Replace ICC brake switch. 2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
5.CHECK ICC BRAKE HOLD RELAY
1. Turn ignition switch OFF.
2. Disconnect ICC brake hold relay.
3. Check ICC brake hold relay. Refer to ACS-64, "
ICC Brake Hold Relay".
OK or NG
OK >> GO TO 6.
NG >> 1. Replace ICC brake hold relay. 2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
6.CHECK HARNESS BETWEEN ICC BRAKE HOLD RELAY AND ICC BRAKE SWITCH
1. Disconnect ICC brake switch connector and ICC unit connector.
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-47
< SERVICE INFORMATION > [ICC]
C
D
E
F
G H
I
J
L
M A
B
ACS
N
O P
2. Check continuity between ICC brake hold relay harness connec- tor and ICC brake switch harness connector.
3. Check continuity between ICC brake hold relay harness connec- tor and ground.
OK or NG
OK >> GO TO 7.
NG >> 1. Repair harness between ICC brake hold relay and ICC brake switch. 2. Erase DTC and perform ICC syst em running test. Then perform self-diagnosis of ICC system
again.
7.CHECK HARNESS BETWEEN ICC UNIT AND ICC BRAKE HOLD RELAY
1. Disconnect ECM connector.
2. Check continuity between ICC unit harness connector and ICC brake hold relay harness connector.
3. Check continuity between ICC unit harness connector and ground.
OK or NG
OK >> GO TO 8.
NG >> 1. Repair harness between ICC unit and ICC brake hold relay. 2. Erase DTC and perform ICC syst em running test. Then perform self-diagnosis of ICC system
again.
8.CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between ICC brake switch harness connector and ground.
OK or NG
OK >> 1. Replace ICC unit. 2. Erase DTC and perform I CC system running test.
Then perform self-diagnosis of ICC system again.
NG >> 1. Repair or replace harness or fuse. 2. Erase DTC and perform ICC syst em running test. Then perform self-diagnosis of ICC system
again.
9.CHECK STOP LAMP ILLUMINATION
ICC brake hold
relay connector Te r m i n a lICC brake switch
connector Terminal Continuity
E14 3 E209 2 Yes
ICC brake hold
relay connector Te r m i n a l
Ground Continuity
E14 3 No
PKIB4167E
ICC unit connector Terminal ICC brake hold relay
connector Terminal Continuity
M89 29 E14 4 Yes
ICC unit connector Terminal GroundContinuity
M89 29 No
SKIA5980E
ICC brake switch connector Te r m i n a l
Voltage (Approx.)
(+) ( −)
E209 1 Ground Battery voltage
PKIB4168E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C