2008 GREAT WALL FLORID lock

Downloaded from www.Manualslib.com manuals search engine 41Clutch Operational System
Clutch Pedal Examination and Adjustment
1. Check if the pedal height is correct.
Height from the carpet: 100-110 mm
2. Adjust the pedal height.
Loosen the lock nut and adjust the clutch pedal limit adjust-
ing bolt until its height is correct, and then tighten the lock
nut.
Tightening torque: 20 N·m
3. Check if the pedal free play is correct.
Step on the pedal until one can feel the resistance.
Pedal free play: 13.7 mm
4. Adjust the free play.
(a) Loosen the lock nuts of the clutch master cylinder and
rotate the push rod until the pedal reaches the correct
free play.
(b) Tighten the lock nuts.
Tightening torque: 20 N·m
(c) Recheck the clutch pedal height.
Pedal height
Lock nut
Limit adjusting bolt
Lock nut
Free play

Downloaded from www.Manualslib.com manuals search engine 43Transmission
Main Technical Parameters
Basic parameters of the 037A transmission
Max. input torque115 N·m/4400-5200 rpm
Speed ratio for each gear3.5451.9131.3100.9730.8043.214
Main deceleration ratio3.944
Odometer speed ratio31/35 (currently no driven gear)
Center distance (mm)65
Lubricant capacity (L)1.8
Control methodRemote cable control
Netweight (kg)28
Match engineGW413EF
037A Transmission’s Overall External Schematics
The 037A transmission is a step mechanical transmission with differential, two-shaft front wheel drive
application. The forward gear has adopted the inertia synchronizer gear-shifting mechanism, which offers
smooth and easy gear shifting, reduces noise dramatically, and improves the service life of the gear - important
in achieving the overall economical efficiency. Regarding its control mechanism, the set steel ball and spring
allow the shifting gear to be quick, accurate with solid handling. The 5th gear transmission is equipped with an
interlocking mechanism to prevent accidental switching to reverse, to im\
prove driving comfort and reliability.

Downloaded from www.Manualslib.com manuals search engine 45Transmission
Areas of Importance
Removal
During removal, all components should be gently handled to avoid knocking, especially the joint surface.
All components should be placed in the proper order to avoid misplacing \
and mistaking.
Installation
1. Clean all parts before installation (except rubber pieces and gaskets)\
.
2. All oil seals, shaft retainers, and elastic pins should not be reused.
3. All rubbing surfaces should be coated with lubricant, and the lips of all oil seals should be coated with
grease.
4. During installation of the bearings, do not use any kind of rolling element to transmit pressure, and
make sure not to tilt it.
5. During the installation of synchronizer components, the two sides of the spring piston's openings
should alternate.
6. When the transmission is operating under normal working conditions, there should be no lubricant
leakage from any of the parts.
Transportation and storage
1. When transporting a transmission, make sure the conditions are dustproof and rainproof, as well as
take proper care not to damage it due to jolting, shaking, removal, or i\
nstallation.
2. Transmission assembly should be stored in a ventilated, dustproof, and dr\
y place.
3. Users with special transportation or storage requirements should have another discussion to reach an
agreement on this matter in the supply contract.
Use partsBolt codeSpecificationsQuantity
Tighten-
ing torque
(N·m)
Differential case × differential ring gear037-2303309M12 × 1.06123.6
C l u t c h h o u s i n g × r e v e r s e g e a r a r m
bracket subassembly037-1702073M8 × 1.25217.2
No. 1 gear shift fork shaft × No. 1 gear
shift fork037-1702056M6 × 0.75115.7
No. 2 gear shift fork shaft × No. 2 gear
shift fork037-1702056M6 × 0.75115.7
Transmission case × clutch housing037-1701012M8 × 1.251329.4
Transmission case × manipulation lid
subassembly037-1702051M8 × 1.25412.0
Transmission case × position mechanism
component037-1702042M18 × 1.5136.8
Transmission case × reverse gear idler
shaft × sealing ring037-1701404M8 × 1.25129.4
Transmission case × hexagon head plug037-1701016M18 × 1.5239.2
Transmission case × reverse gear switch
subassembly037-1701022M18 × 1.5140.2
Transmission case × cable bracket037-1701019M8 × 1.25411.3
Clutch housing × clutch slave cylinder
subassembly037-1601019M8 × 1.25211.3
Select lever assembly × gear shifting
block037-1702027M8 × 1.25138.0
Clutch housing × release fork support
nail037-1601011M10 × 1.25136.8
Counterweight component × shift lever
component037-1702030M8 × 1.25220.0
Release fork support nail129.4
Thread fastening piece tightening torque table

Downloaded from www.Manualslib.com manuals search engine 49Transmission
Gear Shift Fork and Fork Shaft
Components
Clutch housing
No. 1 gear shift fork shaft
Shaft retainers
Set bolt
Elastic cylindrical pin
No. 1 gear shift fork
Elastic cylindrical pin
No. 1 guide block
Lock pin
Pressure spring
Shaft retainers
Lock pin
No. 3 gear shift fork shaft
No. 2 gear shift fork shaft
No. 3 guide block
No. 3 gear shift fork
Set bolt
Output shaft assembly
Input shaft assembly
Gasket
Reverse gear idler shaft
Reverse gear idler assembly
No. 2 gear shift fork
Bracket bolt
Reverse gear arm bracket assembly
Reverse gear gear shift fork
Shaft retainers
Shaft retainers
15.7
15.7
Bolt for flange face
29.4
17.2
: Specified torqueN·m

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual52
5. Remove the reverse gear arm bracket assembly.
6. Remove the No. 1 gear shift fork shaft and the set
bolts.
7. Remove the elastic cylindrical pin from the No. 1 guide
block.
8. Remove the No. 1 gear shift fork, No. 1 gear shift fork
shaft, and No. 1 guide block.

Downloaded from www.Manualslib.com manuals search engine 53Transmission
9. Remove the elastic cylindrical pin from the No. 3 gear
shift fork.
10. Remove the elastic cylindrical pin from the No. 3 guide
block.
11. Remove the No. 3 gear shift fork, compression spring,
and No. 3 guide block.
12. Remove the set bolts from the No. 2 gear shift fork
shaft.

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual54
13. Remove the No. 2 gear shift fork shaft, No. 2 gear shift
fork, and No. 2 guide block.
14. Remove the input and output shaft subassembly.
15. Remove the differential subassembly.
16. Remove the magnetic body from the inside of the
clutch housing.

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual64
Disassembling the Shift Cover Subassembly
Components
Shift lever assembly
Dust cover
T oil seal
Gear shifting block
No. 2 spring seat
Pressure spring
Shaft retainer
Gasket
Lock plateShaft retainerElastic cylindrical pin
Shift guide block
Select lever subassembly
Manipulation lid
T oil seal
1. Remove the shift lever's elastic cylindrical pin.
Set bolt38.0
: Specified torqueN·m