2008 GEELY FC warning

Cooling - Cooling syste2. Check engine coolant level in reservoir.Engine coolant level should be between “Low” and “Full” mark line.
Hint: if the level is too low, check there is leakage and refill coolant to “Full” mark line.3. Check engine coolant quality.(a) Remove radiator cap.
Warning: when the temperature of engine and radiator is high, do not remove radiator cap to
avoid being scalded, because coolant and steam will spurt under high pressure.
(b) Check there is too much rust deposit around radiator cap or at outlet and check there is flake; there
should not be oil in the coolant.
Hint: if coolant is too dirty, it is required to replace coolant.
(c) Install back radiator cap.Inspection1. Temperature regulatorHint: the figure on temperature regulator is the
opening temperature of valve.CoolingCooling systemOn-vehicle inspection1. Check there is leakage with cooling system.Warning: when the temperature of engine and radiator is
high, do not remove radiator cap to avoid be-
ing scalded, because coolant and steam will
spurt under high pressure.
(a) Refill coolant to radiator, and install radiator cap tester.
(b) Preheat engine.
(c) Pump tester to make pressure go up to 118KPa, and check
the pressure falls.
Hint: if the pressure falls, check there is leakage with
hose, radiator or water pump, and check heater,
cylinder body and cylinder head if no external leak-
age is found.66

CoolantReplacement1. Discharge engine coolant.Warning: when the temperature of engine and radiator is high, do not remove radiator cap to
avoid being scalded, because coolant and steam will spurt under high pressure.
(a) Remove radiator cap.
(b) Open radiator drain valve and engine drain valve.Cooling - Coolant2. Refill engine coolant.(a) Lock 2 drain valves and pour coolant into radiator until it is full.
Hints:Press radiator water inlet hose and outlet hose with hands several times.If coolant level is too low, please refill coolant again.
(b) Screw down radiator cap.
(c) Pour coolant into expansion tank until the level is up to “FULL” mark line.
(d) Run engine with vehicle warning up until thermostat valve is opened.
Hint:During vehicle warning up, press radiator water inlet hose and outlet hose with hands
several times.
(e) Engine flames out until coolant temperature falls to “cold”. Then open radiator cap and check coolant
level.
(f) If coolant level is too low, please perform the above steps again.
(g) If coolant level is not too low, please adjust expansion tank coolant level.3. Check there is leakage with coolant.(a) Refill engine coolant to radiator, and install radiator cap tester.
(b) Pressurize radiator to 118kPa, and check there is leakage.73Engine drain valve
Radiator drain valve Radiator cap
Drain pipe

Oil filter assemblyReplacementWarning:Long-term or repeat contacting mineral oil will cause decomposing of natural fat on skin, which
will result in dry and sensitive skin and skin rankling. Used oil has potential harm and may cause
carcinoma cutis.When replacing engine oil, always wear protective clothes and gloves to avoid waste oil
penetrating, and reduce the frequency and time of skin contacting waster oil, and clean with
soapy water or clean water not with gasoline, thinner or solvent if skin contacts waste oil.To protect environment, waste oil and oil filter must be abandoned at named place.1. Remove engine right bottom shield.
2. Discharge engine oil.
3. Remove oil filter assembly [4G18-1012100].Remove oil filter with special tool.4. Install oil filter assembly.(a) Check and clean oil filter junction plane.
(b) Coat oil seal of new oil filter with clean oil.
(c) Tighten oil filter with hands to the extent that oil seal
just touches fixing base.
(d) Tighten oil filter for another 3/4 circle with special tool.5. Install oil drain plug [4G18-1009101].Clean oil drain plug, and install it back after replacing oil drain plug gasket.
Torque: 6. Refill engine oil.
7. Check there is oil leakage.Lubrication - Oil filter assemblySpecial tool75Special tool 3/4 circle

Brake--Front brake assemblyFront brake assemblyOverhaul1. Disassemble front wheels.
2. Discharge brake liquid.Note: do not spill the brake liquid on paint surface of automobile body, if having, wash it cleanly.3. Disassemble brake branch pump assembly.(a) Disassemble the bolts and gaskets of brake hose joint on
brake branch pump, then disassemble brake hose.
Hint: the gasket has two types: two sheets type or one
type.
(b) Fix sliding pin of cylinder body to disassemble two bolts.4. Disassemble brake block of front wheels.(a) Disassemble brake block with muffle gasket.
(b) Disassemble muffle gasket from every brake block.5. Disassemble support sheet of brake block.
6. Disassemble sliding pin of brake branch pump.Disassemble sliding pin on branch pump bracket.7. Disassemble dustproof cover on brake branch pump.Disassemble two dustproof covers from brake branch pump
of disk.8. Disassemble left front brake branch pump.Disassemble two bolts and brake branch pump bracket.9. Disassemble dustproof cover of branch pump.Use screw driver to disassemble oil seal loop and dustproof
cover.10. Disassemble the piston of brake branch pump.(a) Put a cloth or similar thing between piston and branch pump.
(b) Use compressed air to disassemble piston from branch
pump.
Warning: when using compressed air, do not put your
finger at the front of piston.
Note: you could not be splashed by brake liquid.11. Disassemble oil seal of piston.Use screw driver to disassemble oil seal of piston from branch
pump.12. Disassemble exhaust bolt of branch pump.Brake branch pump
Dustproof cover141

Brake--Rear brake assemblyRear brake assembly
OverhaulHint: overhaul procedure for right side is same as the left side.1. Disassemble rear wheels.
2. Discharge brake liquid.Note: do not spill the brake liquid on paint surface of automobile body, if having, wash it cleanly.3. Disassemble brake block of rear wheels.(a) Disassemble fixing clamp of anti-vibration spring.
(b) Disassemble two guide pins of brake block and brake block
with muffle gasket.
(c) Take down muffle gasket from every brake block.4. Disassemble left rear brake branch pump.(a) Disassemble the joint, bolt and gasket of brake hose of brake
branch pump, then disassemble brake hose.
Hint: gasket has two types: two sheets type and one
sheet type
(b) Disassemble two bolts and brake branch pump.5. Disassemble the bushing of brake branch pump.Disassemble two bushings from brake branch pump.6. Disassemble dustproof bushing of rear brake.Disassemble three dustproof bushings.7. Disassemble dustproof cover of branch pump.Use screw driver to disassemble fixing loop and dustproof cover.8. Disassemble the piston of brake branch pump.(a) Put a cloth or similar thing between the piston and branch
pump.
(b) Use compressed air to disassemble piston from branch
pump.
Warning: when using compressed air, do not put your
fingers at the front of piston.
Note: do not let brake liquid splash on you.9. Disassemble oil seal of piston.144

Steering column system
Overhaul
1. Put the front wheels towards the front.
2. Disassemble safety airbag assembly at the side of
driver (equipping with SRS) [67000179]
Note: if disconnecting airbag joint when ignition switch
locates at ON position, checking number will record it.
(a) Put the front wheels towards the front.
(b) Use planetary sleeve wrench to loosen two planetary
screws until the concave slot around the screw contacts
the screw shell.
(c) Pull out airbag assemble from steering wheel, and
disassemble airbag joint.
(d) Disassemble the terminal.
Warning:
¡ñ¡ñ
¡ñ¡ñ¡ñWhen storing safety airbag assembly at the side
of driver, it is necessary to put the surface of
airbag assembly towards the upside.
¡ñ¡ñ
¡ñ¡ñ¡ñDo not disassemble airbag assembly.
Note: when disassembling airbag assembly, pay
attention not to pull airbag wiring harness.
3. Disassemble steering wheel assembly [67100001]
(a) Disassemble the fixed screw cap of steering wheel.
(b) Make corresponding marks on steering wheel and main
shaft assembly.
(c) Use special tool to disassemble steering wheel.
4. Disassemble upper/lower decoration plate of
steering column [64000128/64000129]
5. Disassemble left combination switch assembly
[67000078] (referring to page 298)
Steering column--Steering systemSteering column--Steering system
Steering column--Steering systemSteering column--Steering systemSteering column--Steering system
airbag joint
Correct Wrongplanetary
screws screw shell
 194 
Align the mark

Steering column--Steering systemSteering column--Steering system
Steering column--Steering systemSteering column--Steering systemSteering column--Steering system
Align the mark
(b) Align the mark on sliding yoke and middle shaft.
(c) Assemble B bolt and tighten A bolt.
Torque: 35 ± 3 Nxm
Hint:When changing new sliding yoke, it is neces-
sary to adjust the front wheel at the front, and
make the bolt hole surface of sliding yoke face
the back (liking that shown in figure), then as-
semble the bolt.
21. Adjust front wheel at the front.
22. Assemble helix cable assembly (equipping with
SRS) [67000121]
23. Put the helix cable assembly at central position
(equipping with SRS)
(a) Check whether the front wheel faces the front.
(b) Turn helix cable counter-clockwise with hand until it could
not turn.
(c) Then turn helix cable 2.5 clockwise and align the mark.
Hint:helix cable could turn left or right from central
position for 2.5 rounds.
24. Assemble steering wheel assembly [67010001]
(a) Align the mark on steering wheel and main shaft assembly.
(b) Assemble the fixed screw cap of steering wheel.
(c) Connect the joint.
25. Assemble safety airbag assembly at the side of driver [67010011]
Warning:
zForbid using SRS parts on other automobiles, when changing any part, it is necessary to use new
product.
zIf safety airbag assembly at the side of driver once dropped or exterior shell and joint has crack,
concave or other distortions, it is necessary to change with new product.
zWhen assembling the airbag assemble at the side of driver, it is necessary to pay attention to airbag
wiring harness could not interrupt other parts or be clamped by other parts.
(a) Connect the end.
(b) Connect the joint of airbag.
(c) After assembling the safety airbag assembly at the side
of driver, insure planetary screw of concave slot contacts
with screw shell.
(d) Use planetary screwdriver to tighten two screws.
Torque: 8.8 Nxm
26. Check the central point of steering wheel
27. Check SRS warning light (equipping with SRS)
Align the
mark
 197 
planetary
screws screw shell

Air conditioner--Air conditioning system
Air conditioner
Air conditioning system
Note
1. Do not dispose Refrigerant in sealed space or near
flame.
2. Wear glasses to protect your eyes.
3. Do not let liquid Refrigerant contact with your eyes
or skin.
If liquid Refrigerant contacts with your eyes or skin:
(a) Wash the contacted part with much water.
Warning: do not knead your eyes or skin.
(b) Spread clean Vaseline on your skin.
(c) Go to doctor or hospital for special cure.
4. Forbid heating it or making it expose the flame.
5. Forbid dropping the Refrigerant tank or shake it
intensively.
6. Do not operate compressor when Refrigerant is lack.
If the Refrigerant in cooling system is lack, it will incur com-
pressor burned out for lacking lubrication. So it is necessary
to avoid.
7. Do not open the high pressure valve of filling instru-
ment package when compressor is working.
If opening the valve at this time, Refrigerant will flow back into
refrigerant tank to incur the tank will break. So only the low
pressure valve could be opened or closed.
8. Do not fill Refrigerant too much.
Too much refrigerant will make many problems such as lack
cooling degree, oil consumption, too hot engine and so on.
Inspection on automobile
1. Check the No.1 pressure switch.
(a) Control for electromagnetic clutch:
Check the function of pressure switch.
(1) Assembly filling instrument package.
(2) Connect the anode lead of OUM meter to No. 4 termi-
nal and connect cathode lead to No. 1 terminal.
(3) Liking that shown in figure. When refrigerant pressure
is changed, check the conduction between terminals.
wrong correct
Low-pressure
sideHigh-pressure
side
Not
conductionCon-
duction
Not
conduction
 213